Linksys WRT54G v3.1

From TechInfoDepot
Jump to navigationJump to search
multiple revisions of this device, use caution
bg (G54)
Wireless-G Broadband Router
Linksys WRT54G-02.jpg
Support
Downloads
Wikipedia
InfoDepot Wiki
WikiDevi.wi-cat.ru
3rd Party Firmware
dd-wrt
OpenWrt
Tomato any flavor
Gargoyle
Status Unknown
Platform
BrandModelRev
Linksys WRT54G v3.1
Serial number prefix
CDF9
FCC ID
IC ID
Type
wireless router
Series
WRT54G
CPU1
CPU1 Type
MIPS BMIPS3300
CPU1 Speed
216 MHz
Flash1 Chip
Intel TE28F320C3BD70
Flash1 Size
4 MiB4,194,304 B <br />32,768 Kib <br />4,096 KiB <br />32 Mib <br />0.00391 GiB <br /> (Parallel)
RAM1 Size
16 MiB16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br />
RAM1 Chip
SK hynix HY5DU281622ET-J
ETH chip1
Switch
Broadcom BCM5325E
Ethernet Port Count
1-100MbE-WAN
4-100MbE-LAN
Wired Standard
IEEE 802.3/3u
Port-based vlan
Yes

802dot11 OUI: 00:13:10 (16 E, 17 W), 00:14:BF (10 E, 13 W)
Ethernet OUI: 00:13:10 (16 E, 17 W), 00:14:BF (10 E, 13 W)

Stock bootloader
CFE
Expansion IF types
none specified
Power
12 VDC, 1 A
Connector type
barrel
Serial Port (UART)
yes
JTAG Port
yes
Other

Default SSID: linksys (53 addl. devices)
Default IP address: 192.168.1.1
the IP 192.168.1.1 is used by 1308 additional devices
of which 153 are Linksys devices
Default login user: blank
Default login password: admin
blank:admin credentials used by 267 additional devices
of which 134 are Linksys devices

Default Channel(s)
6
Manuf/OEM/ODM
3rd Party Firmware Support
DD-WRT • (List)
, OpenWrt • (List | Dev | DLs)
, Tomato • (List | DLs)
, TomatoUSB • (List | DLs)
Retail
Availability End of Life
FCC approval date 17 September 2004
Radio 1
Chip1
Chip2
Broadcom BCM2050
Wireless interface OUI
00:13:10,00:14:BF
Antenna Connector Type
RP-TNC
Wireless Standard
IEEE 802.11b/g
802.11g
up to 54 Mbps
802.11b
up to 11 Mbps
WiFi Operating Frequency
2.4 GHz
Radio cor_rev
7
 FCC ID
Linksys WRT54G v2.2Q87-WT54GV22
Linksys WRT54G v3.0Q87-WT54GV22
Linksys WRT54GS v1.1Q87-WT54GV22
Linksys WRT54GS v2.0Q87-WT54GV22
Linksys WRT54GS v2.1Q87-WT54GV22
 CPU1 brandRadio1 chip1 brandRadio1 chip2 brand
Linksys WRT54G v1.0BroadcomBroadcomBroadcom
Linksys WRT54G v1.1BroadcomBroadcomBroadcom
Linksys WRT54G v2.0BroadcomBroadcomBroadcom
Linksys WRT54G v2.2BroadcomBroadcomBroadcom
Linksys WRT54G v3.0BroadcomBroadcomBroadcom
Linksys WRT54G v3.1BroadcomBroadcomBroadcom
Linksys WRT54G v4BroadcomBroadcomBroadcom
Linksys WRT54G v5.0BroadcomBroadcomBroadcom
Linksys WRT54G v5.1BroadcomBroadcomBroadcom
Linksys WRT54G v5.2BroadcomBroadcomBroadcom
Linksys WRT54G v6.0BroadcomBroadcomBroadcom
Linksys WRT54G v7.0AtherosAtheros
Linksys WRT54G v7.2BroadcomBroadcom
Linksys WRT54G v8.0BroadcomBroadcom
Linksys WRT54G v8.1BroadcomBroadcom
Linksys WRT54G v8.2BroadcomBroadcom
Linksys WRT54G-TMBroadcomBroadcomBroadcom
Linksys WRT54GHRalinkRalink
Linksys WRT54GP2MarvellMarvellMarvell
Linksys WRT54GP2A-ATIntel XScaleInprocommRFMD

For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.

For a list of all currently documented Linksys device with specifications, see Linksys.

54 Mbps - 2.4GHz 802.11g = G54 class

Overview

Links of Interest

Flashing

Flashing DD-WRT

 

  1. Read the peacock announcement found here: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486
  2. Do a Hard reset or 30/30/30 on the router according to note 1 of the peacock announcement (30/30/30)
  3. Set a static IP on your computer to 192.168.1.7. Subnet mask should be 255.255.255.0.
  4. Connect the lan cable from your computer to a LAN port of your router. Make sure your router is plugged in. Nothing should be connected to your computer or the router except the lan cable between them. Turn your firewall and any wireless computer connections OFF.
  5. Power cycle the router (uplug the power from the router for 30 seconds and then plug it back in)
  6. Open your browser to 192.168.1.1 by putting that in the browser address window of your browser. You should open the linksys webgui and NOT a page that says Management Mode. If you see management mode, power cycle the router again.
  7. Leave the username blank and enter "admin" as the password
  8. Go to administration and firmware upgrade
  9. Navigate to the folder that you are using, and select dd-wrt.v24-15230_VINT_mini.bin
  10. Hit upgrade
  11. When you get a message that the upgrade is successful, wait FIVE FULL minutes before continuing.
  12. If you don't get success, repeat from steps 6 up to this one. If you still don't get success, clear your browser cache. Try using a different browser as well, to navigate to 192.168.1.1.
  13. When you can access the dd-wrt webgui using a browser at 192.168.1.1, power cycle the router.
  14. When you can again access the dd-wrt webgui using a browser at 192.168.1.1, do another Hard reset or 30/30/30 on the router.
  15. At this point you can choose to put a different build on, depending on what you needs are.
  16. Reset your computer ethernet connection to auto IP and auto DNS
  17. Check for recommended builds here.

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)
On the OpenWrt Wiki
Support started version: 0.9
Current supported version: 10.03.1

Please insert instructions here

Flashing Tomato

Please insert instructions here

Reverting

Reverting to OEM Firmware from DD-WRT

  1. Read the peacock announcement found here: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486
  2. Do a Hard reset or 30/30/30 on the router according to note 1 of the peacock announcement (30/30/30)
  3. Set a static IP on your computer to 192.168.1.7. Subnet mask should be 255.255.255.0.
  4. Connect the lan cable from your computer to a LAN port of your router. Make sure your router is plugged in. Nothing should be connected to your computer or the router except the lan cable between them. Turn your firewall and any wireless computer connections OFF.
  5. Power cycle the router (uplug the power from the router for 30 seconds and then plug it back in)
  6. Open your browser to 192.168.1.1 by putting that in the browser address window of your browser. You should open the linksys webgui and NOT a page that says Management Mode. If you see management mode, power cycle the router again.
  7. Enter your username and password
  8. Go to administration and firmware upgrade
  9. Navigate to the folder that you are using, and select WRT54G_v4.21.1_fw.zip once you've unzipped it.
  10. Hit upgrade
  11. When you get a success, wait FIVE FULL minutes.
  12. When you can again access the Linksys webgui using a browser at 192.168.1.1, do another Hard reset or 30/30/30 on the router.
  13. Reset your computer ethernet connection to auto IP and auto DNS

JTAG-Serial Info

JTAG

JTAG Pinouts

nTRST   1o o2	GND
  TDI   3o o4	GND
  TDO   5o o6	GND
  TMS   7o o8	GND
  TCK   9o o10	GND
nSRST  11o o12  N/C

Serial

Serial Pinouts

VCC  1 o o 2  VCC
TX1  3 o o 4  TX0
RX1  5 o o 6  RX0
N/C  7 o o 8  N/C
GND  9 o o 10 GND

vlan Info

Pictures

Images
FCCID Q87-WT54GV22