APRESIA GS120GT-SS
From TechInfoDepot
Jump to navigationJump to search
| Web smart switch | |
 | |
| Homepage | Product page |
|---|---|
| WikiDevi.wi-cat.ru | APRESIA GS120GT-SS |
| 3rd Party Firmware | |
| dd-wrt | Status Unknown |
| OpenWrt | Supported |
| Tomato any flavor | Incompatible |
| Gargoyle | Status Unknown |
| Platform | |
| Brand • Model • Rev | APRESIA GS120GT-SS |
| Model part number | APLGS120GTSS |
CPU1  | Realtek RTL8382M |
| CPU1 Type | MIPS 4KEc |
| CPU1 Speed | 500 MHz |
| Flash1 Chip | Macronix MX25L25635FMI-10G |
| Flash1 Size | 32 MiB 33,554,432 B <br />262,144 Kib <br />32,768 KiB <br />256 Mib <br />0.0313 GiB <br /> (SPI NOR) |
| RAM1 Size | 256 MiB 268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br /> (DDR3) |
| RAM1 Chip | Nanya NT5CC256M8JQ-EK |
| ETH chip1 | Realtek RTL8382M |
| ETH chip2 | Realtek RTL8218B |
| ETH chip3 | Realtek RTL8214FC |
| Switch | Realtek RTL8382M |
| Ethernet Port Count | 16-1GbE |
| Ethernet connector | 8P8C |
| Wired Standard | IEEE 802.3i/3u/3ab |
| Auto-MDIX | supported |
| Jumbo frame | yes |
| Switch Class | smart |
|
Ethernet OUI: none specified | |
| Expansion IF types | SFP |
| SFP ports | 4 |
| Stock bootloader | U-Boot |
| Power | 100-240 VAC ~ 50/60 Hz, ? A |
| Connector type | C13 |
| Serial Port (UART) | yes, 3.3V TTL, (115200 8N1) |
| Other | |
|
| |
|
Flags: LACP | |
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) |
For a list of all currently documented Realtek chipsets with specifications, see Realtek.
Links of Interest
Models
- ・ApresiaLight GS110GT-SS • 8x 1G, 2x SFP
- ・ApresiaLight GS120GT-SS • 16x 1G, 4x SFP
- ・ApresiaLight GS128GT-SS • 24x 1G, 4x SFP
- ・ApresiaLight GS152GT-SS • 48x 1G, 4x SFP
Flashing
 | NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
Target: realtek
Subtarget: rtl838x
Package architecture: mips_4kec
Supported Since Commit
Support started version: 23.05.0
Current supported version: 25.12.1
Subtarget: rtl838x
Package architecture: mips_4kec
Supported Since Commit
Support started version: 23.05.0
Current supported version: 25.12.1
LAN Hardware: Realtek RTL8382M
LAN Comment: Ethernet ports 17-20 shared with 4 SFP ports
WLAN Hardware: none
Installation method(s):
GUI OEM
Recovery method(s):
U-Boot TFTP + serial recovery
LAN Comment: Ethernet ports 17-20 shared with 4 SFP ports
WLAN Hardware: none
Installation method(s):
GUI OEM
Recovery method(s):
U-Boot TFTP + serial recovery
| git • >> |
|---|
realtek: add support for APRESIA ApresiaLightGS120GT-SS
APRESIA ApresiaLightGS120GT-SS (APLGS120GTSS) is a 16 + 4 ports gigabit
switch, based on RTL8382M.
Specifications:
- SoC : Realtek RTL8382M
- RAM : DDR3 256 MiB (Nanya NT5CC256M8JQ-EK)
- Flash : SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G)
- Ethernet : 10/100/1000 Mbps x16 + 4
- port 1-8 : RTL8218B
- port 9-16 : RTL8382M, TP (SoC, RTL8218B)
- port 17-20 : RTL8214FC, TP/SFP (Combo)
- LEDs/Keys : 3x/1x
- UART : through-hole on PCB
- J6: 3.3V, TX, RX, GND from tri-angle marking side
- 115200n8
- Power : 100-120/200-240 VAC, 50/60 Hz
Max. 16 W, Avg 14 W (100 VAC)
- Plug : IEC 60320-C13
Flash instruction using factory image:
1. Boot ApresiaLightGS120GT-SS normally
2. Login to WebUI and open firmware page ("ファームウェア")
3. If the device is booted from image1, set active image for next
booting ("起動イメージ選択") to image2("イメージ2"), press apply
("適用") button and reboot the device to make booting from image2
4. On the WebUI, set active image to image1
5. Select the OpenWrt factory image and press update button ("更新")
6. Open reboot page ("再起動") and press reboot button ("再起動実行")
Notes:
- "ApresiaLightGS120GT-SS" is a model name and "APLGS120GTSS" is a model
number
- this device has 3x GPIO-controlled LEDs on PCB, but 1x LED
("green:unused") has no hole on the case
|
