ASUS RT-AC1300UHP
From TechInfoDepot
Jump to navigationJump to search
| abgn+ac (AC1300) | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| AC1300 Dual-Band Wi-Fi Gigabit Router | |||||||||||||
|
| |||||||||||||
| Wikipedia | Asus routers | ||||||||||||
| WikiDevi.wi-cat.ru | ASUS RT-AC1300UHP | ||||||||||||
| 3rd Party Firmware | |||||||||||||
| dd-wrt | Status Unknown | ||||||||||||
| OpenWrt | Supported | ||||||||||||
| Tomato any flavor | Incompatible | ||||||||||||
| Gargoyle | Status Unknown | ||||||||||||
| Platform | |||||||||||||
| Brand • Model • Rev | ASUS RT-AC1300UHP | ||||||||||||
| FCC ID (fcc.io) | MSQ-RTACRH00 | ||||||||||||
| FCC ID (fcc.report) | MSQ-RTACRH00 | ||||||||||||
| Type | wireless router | ||||||||||||
| CPU1 | Qualcomm IPQ4018 | ||||||||||||
| CPU1 Type | ARMv7 Cortex-A7 | ||||||||||||
| CPU1 Speed | 710 MHz ( 4 cores ) | ||||||||||||
| Flash1 Chip | Winbond W25N01GVZEIG | ||||||||||||
| Flash1 Size | 128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (NAND) | ||||||||||||
| Flash2 Chip | Macronix MX25L1606EM2I-12G | ||||||||||||
| Flash2 Size | 2 MiB 2,097,152 B <br />16,384 Kib <br />2,048 KiB <br />16 Mib <br />0.00195 GiB <br /> (SPI NOR) | ||||||||||||
| RAM1 Size | 128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (DDR3L-1066 537 MHz) | ||||||||||||
| RAM1 Chip | Nanya NT5CC64M16GP-DI | ||||||||||||
| nvram Size | 64K | ||||||||||||
| ETH chip1 | Qualcomm IPQ4018 | ||||||||||||
| Switch | Qualcomm Atheros QCA8075 | ||||||||||||
| Ethernet Port Count |
1-1GbE-WAN 4-1GbE-LAN | ||||||||||||
| Wired Standard | IEEE 802.3i/3u/3ab | ||||||||||||
| Stock bootloader | U-Boot | ||||||||||||
| Stock FW OS | Linux 3.14 | ||||||||||||
| Expansion IF types | USB 3.0 | ||||||||||||
| USB ports | 1 | ||||||||||||
| USB Hub Compatible | Untested | ||||||||||||
| Power | 12 VDC, 1.5 A | ||||||||||||
| Connector type | barrel | ||||||||||||
| Serial Port (UART) | yes, 4-pin header, (115200 8N1) | ||||||||||||
|
Flags: | |||||||||||||
|
Additional chips | |||||||||||||
| Other | |||||||||||||
|
| |||||||||||||
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) | ||||||||||||
| Retail | |||||||||||||
| Availability | End of Life | ||||||||||||
| Physical | |||||||||||||
| Dimensions | 207 x 148.8 x 35.5 mm (LxWxH) | ||||||||||||
| Weight | Weight: 395 g | ||||||||||||
| Radio 1 | |||||||||||||
| Chip1 | Qualcomm IPQ4018 | ||||||||||||
| Wireless interface OUI | AC:9E:17, 38:D5:47 | ||||||||||||
| Antenna Connector Type | U.FL | ||||||||||||
| MIMO status | 2x2:2 | ||||||||||||
| Wireless Standard | IEEE 802.11b/g/n | ||||||||||||
| N-QAM | up to 400 Mbps | ||||||||||||
| 802.11n | up to 300 Mbps | ||||||||||||
| 802.11g | up to 54 Mbps | ||||||||||||
| 802.11b | up to 11 Mbps | ||||||||||||
| WiFi Operating Frequency | 2.4 GHz | ||||||||||||
| Radio 2 | |||||||||||||
| Chip1 | Qualcomm IPQ4018 | ||||||||||||
| Wireless interface OUI | AC:9E:17, 38:D5:47 | ||||||||||||
| Antenna Connector Type | U.FL | ||||||||||||
| MIMO status | 2x2:2 | ||||||||||||
| Wireless Standard | IEEE 802.11a/n/ac | ||||||||||||
| 802.11ac | up to 867 Mbps | ||||||||||||
| 802.11n | up to 300 Mbps | ||||||||||||
| 802.11a | up to 54 Mbps | ||||||||||||
| WiFi Operating Frequency | 5 GHz | ||||||||||||
| |||||||||||||
| |||||||||||||
For a list of all currently documented Qualcomm chipsets with specifications, see Qualcomm.
For a list of all currently documented Qualcomm Atheros (QCA) chipsets with specifications, see Qualcomm Atheros.
For a list of all currently documented ASUS devices with specifications, see ASUS.
Flashing
| NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
Target: ipq40xx
Subtarget: generic
Package architecture: arm_cortex-a7_neon-vfpv4
Supported Since Commit
Support started version: 18.06.0
Current supported version: 24.10.4
Subtarget: generic
Package architecture: arm_cortex-a7_neon-vfpv4
Supported Since Commit
Support started version: 18.06.0
Current supported version: 24.10.4
| git • >> |
|---|
ipq40xx: add support for ASUS RT-AC58U/RT-ACRH13
This patch adds support for ASUS RT-AC58U/RT-ACRH13.
hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI
NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE)
NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI)
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one Reset and one WPS button
LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each)
Serial:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has an unpopulated
1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the
PCB right next to the connector.
U-Boot Note: The ethernet driver isn't always reliable and can sometime
time out... Don't worry, just retry.
Access via the serial console is required. As well as a working
TFTP-server setup and the initramfs image. (If not provided, it
has to be built from the OpenWrt source. Make sure to enable
LZMA as the compression for the INITRAMFS!)
To install the image permanently, you have to do the following
steps in the listed order.
1. Open up the router.
There are four phillips screws hiding behind the four plastic
feets on the underside.
2. Connect the serial cable (See notes above)
3. Connect your router via one of the four LAN-ports (yellow)
to a PC which can set the IP-Address and ssh and scp from.
If possible set your PC's IPv4 Address to 192.168.1.70
(As this is the IP-Address the Router's bootloader expects
for the tftp server)
4. power up the router and enter the u-boot
choose option 1 to upload the initramfs image. And follow
through the ipv4 setup.
Wait for your router's status LED to stop blinking rapidly and
glow just blue. (The LAN LED should also be glowing blue).
3. Connect to the OpenWrt running in RAM
The default IPv4-Address of your router will be 192.168.1.1.
1. Copy over the openwrt-sysupgrade.bin image to your router's
temporary directory
# scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp
2. ssh from your PC into your router as root.
# ssh root@192.168.1.1
The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key.
Once connected...: run the following commands on your temporary installation
3. delete the "jffs2" ubi partition to make room for your new root partition
# ubirmvol /dev/ubi0 --name=jffs2
4. install OpenWrt on the NAND Flash.
# sysupgrade -v /tmp/openwrt-sysupgrade.bin
- This will will automatically reboot the router -
|
Categories:
- ASUS
- Embedded system/wireless router
- Embedded System Qualcomm
- Embedded System IPQ4018
- Qualcomm
- Embedded System ARMv7
- Embedded System Cortex-A7
- Embedded System Qualcomm Atheros
- Embedded System QCA8075
- Qualcomm Atheros
- OpenWrt Supported
- Has Mimo Status
- Embedded System IEEE 802.11b/g/n
- Embedded System IEEE 802.11a/n/ac
- Dual-Radio Wireless Embedded System
- Wireless Embedded System
- Dual-Band
- Embedded System
- English Documentation