+
============= BOOTLOADER STARTUP =============
Flash id read c22018
No network interfaces found
=> Bootloader Version: 1.0.4
=> RAM: 64M FLASH: 16M
=> MFG State: 48
=> MAC Address [Board Data]: 00:19:92:xx:xx:xx
=> Serial Num [Board Data]: 1802xxxxxxxxxx
FIS Filesystem Integrity Check...OK
Firmware integrity check...
== Executing boot script in 5.000 sec - enter password to abort ==
fis load -l vmlinux_2;exec
Image loaded from 0x80060000-0x805dea82
Now booting linux kernel:
Base address 0x80050000 Entry 0x80060000
Cmdline :
[ 0.000000] Linux version 4.19.79 (builder@sunny) (gcc version 8.3.0 (OpenWrt GCC 8.3.0 r11358-f526e85426)) #0 Tue Oct 29 13:28:49 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] MIPS: machine is Adtran/Bluesocket BSAP-1800 v2
[ 0.000000] SoC: Atheros AR7161 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] random: get_random_bytes called from start_kernel+0x98/0x4a8 with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00077d32
[ 0.000000] Readback ErrCtl register=00077d32
[ 0.000000] Memory: 57588K/65536K available (4273K kernel code, 178K rwdata, 1008K rodata, 1188K init, 206K bss, 7948K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] CPU clock: 600.000 MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370868154 ns
[ 0.000008] sched_clock: 32 bits at 300MHz, resolution 3ns, wraps every 7158278654ns
[ 0.007773] Calibrating delay loop... 398.13 BogoMIPS (lpj=1990656)
[ 0.074023] pid_max: default: 32768 minimum: 301
[ 0.078871] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.085463] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.096414] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.106250] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.112438] pinctrl core: initialized pinctrl subsystem
[ 0.118448] NET: Registered protocol family 16
[ 0.427646] PCI host bridge /ahb/apb/pcie-controller@17010000 ranges:
[ 0.434086] MEM 0x0000000010000000..0x0000000016ffffff
[ 0.439292] IO 0x0000000000000000..0x0000000000000000
[ 0.460061] PCI host bridge to bus 0000:00
[ 0.464157] pci_bus 0000:00: root bus resource [mem 0x10000000-0x16ffffff]
[ 0.471052] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.476600] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.483366] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.492506] pci 0000:00:11.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
[ 0.499302] pci 0000:00:12.0: BAR 0: assigned [mem 0x10010000-0x1001ffff]
[ 0.508937] clocksource: Switched to clocksource MIPS
[ 0.514957] NET: Registered protocol family 2
[ 0.520074] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes)
[ 0.527738] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.534733] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.541088] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.547550] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.553410] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.559967] NET: Registered protocol family 1
[ 0.566879] Crashlog allocated RAM at address 0x3f00000
[ 0.573313] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[ 0.586025] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.591882] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.612139] io scheduler noop registered
[ 0.616046] io scheduler deadline registered (default)
[ 0.622009] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.628915] console [ttyS0] disabled
[ 0.632556] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 10, base_baud = 9375000) is a 16550A
[ 0.641247] console [ttyS0] enabled
[ 0.641247] console [ttyS0] enabled
[ 0.648185] bootconsole [early0] disabled
[ 0.648185] bootconsole [early0] disabled
[ 0.661732] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.666841] Searching for RedBoot partition table in spi0.0 at offset 0xfd0000
[ 0.774611] 8 RedBoot partitions found on MTD device spi0.0
[ 0.780201] Creating 8 MTD partitions on "spi0.0":
[ 0.784975] 0x000000000000-0x000000040000 : "RedBoot"
[ 0.790745] 0x000000040000-0x000000170000 : "vmlinux_1"
[ 0.796612] 0x000000170000-0x0000004d0000 : "root_1"
[ 0.802277] 0x0000004d0000-0x000000690000 : "vmlinux_2"
[ 0.808150] 0x000000690000-0x000000fc0000 : "rootfs"
[ 0.813793] mtd: device 4 (rootfs) set to be root filesystem
[ 0.822255] 1 squashfs-split partitions found on MTD device rootfs
[ 0.828420] 0x000000a00000-0x000000fc0000 : "rootfs_data"
[ 0.834577] 0x000000fc0000-0x000000fd0000 : "Board data"
[ 0.840595] 0x000000fd0000-0x000000fe0000 : "FIS directory"
[ 0.846801] 0x000000fe0000-0x000000fe1000 : "RedBoot config"
[ 0.854014] libphy: Fixed MDIO Bus: probed
[ 0.860605] ag71xx 19000000.eth: invalid MAC address, using random address
[ 1.200748] libphy: ag71xx_mdio: probed
[ 1.299044] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:00 [uid=00070421, driver=Vitesse VSC8601]
[ 1.309239] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii-id
[ 1.317587] NET: Registered protocol family 10
[ 1.326078] Segment Routing with IPv6
[ 1.329891] NET: Registered protocol family 17
[ 1.334375] 8021q: 802.1Q VLAN Support v1.8
[ 1.350979] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.361123] Freeing unused kernel memory: 1188K
[ 1.365634] This architecture does not have kernel memory protection.
[ 1.372068] Run /sbin/init as init process
[ 2.588948] random: fast init done
[ 2.753303] init: Console is alive
[ 2.756894] init: - watchdog -
[ 4.257582] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.327432] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 4.345519] init: - preinit -
[ 5.878550] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.090285] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.192421] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.645637] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 9.927750] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
[ 9.934991] jffs2_build_filesystem(): unlocking the mtd device...
[ 9.934995] done.
[ 9.943063] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 10.844418] eth0: link up (1000Mbps/Full duplex)
[ 10.862761] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 44.654603] random: crng init done
[ 44.658006] random: 5 urandom warning(s) missed due to ratelimiting
[ 51.158703] done.
[ 51.160710] jffs2: notice: (466) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 51.178105] mount_root: overlay filesystem has not been fully initialized yet
[ 51.201481] mount_root: switching to jffs2 overlay
[ 51.228419] overlayfs: upper fs does not support tmpfile.
- config restore -
[ 51.770828] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 51.958770] eth0: link down
[ 51.972830] procd: - early -
[ 51.975796] procd: - watchdog -
[ 52.594801] procd: - watchdog -
[ 52.598208] procd: - ubus -
[ 52.669635] procd: - init -
Please press Enter to activate this console.
[ 53.418843] kmodloader: loading kernel modules from /etc/modules.d/*
[ 53.583144] Loading modules backported from Linux version v5.4-rc2-0-gda0c9ea146cb
[ 53.590739] Backport generated by backports.git v5.4-rc2-1-0-g5a0c323a
[ 53.659792] xt_time: kernel timezone is -0000
[ 53.770083] PPP generic driver version 2.4.2
[ 53.789919] NET: Registered protocol family 24
[ 53.858928] ath9k 0000:00:11.0: enabling device (0000 -> 0002)
[ 54.663892] ieee80211 phy0: Atheros AR9160 MAC/BB Rev:1 AR2133 RF Rev:b0 mem=0xb0000000, irq=15
[ 54.672772] ath9k 0000:00:12.0: enabling device (0000 -> 0002)
[ 55.479672] ieee80211 phy1: Atheros AR9160 MAC/BB Rev:1 AR5133 RF Rev:b0 mem=0xb0010000, irq=16
[ 55.766510] urngd: v1.0.1 started.
[ 56.846990] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 69.920163] eth0: link up (1000Mbps/Full duplex)
[ 69.925329] br-lan: port 1(eth0) entered blocking state
[ 69.930609] br-lan: port 1(eth0) entered disabled state
[ 69.936130] device eth0 entered promiscuous mode
[ 69.989067] br-lan: port 1(eth0) entered blocking state
[ 69.994282] br-lan: port 1(eth0) entered forwarding state
[ 69.999854] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 70.919030] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 79.208785] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 79.292683] br-lan: port 2(wlan1) entered blocking state
[ 79.297979] br-lan: port 2(wlan1) entered disabled state
[ 79.303639] device wlan1 entered promiscuous mode
[ 79.439817] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 79.548803] br-lan: port 3(wlan0) entered blocking state
[ 79.554155] br-lan: port 3(wlan0) entered disabled state
[ 79.560089] device wlan0 entered promiscuous mode
[ 79.564878] br-lan: port 3(wlan0) entered blocking state
[ 79.570246] br-lan: port 3(wlan0) entered forwarding state
[ 80.279389] br-lan: port 3(wlan0) entered disabled state
[ 86.513789] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 86.520340] br-lan: port 3(wlan0) entered blocking state
[ 86.525632] br-lan: port 3(wlan0) entered forwarding state
BusyBox v1.31.0 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r11358-f526e85426
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel master br-lan state UP qlen 1000
link/ether 00:19:92:xx:xx:xx brd ff:ff:ff:ff:ff:ff
5: br-lan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP qlen 1000
link/ether 00:19:92:xx:xx:xx brd ff:ff:ff:ff:ff:ff
inet 10.1.1.176/16 brd 10.108.1.255 scope global br-lan
valid_lft forever preferred_lft forever
inet6 fe80::219:92ff:fe0d:bee0/64 scope link
valid_lft forever preferred_lft forever
6: wlan1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue master br-lan state DOWN qlen 1000
link/ether 00:19:92:xx:xx:xx brd ff:ff:ff:ff:ff:ff
7: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master br-lan state UP qlen 1000
link/ether 00:19:92:xx:xx:xx brd ff:ff:ff:ff:ff:ff
inet6 fe80::219:92ff:fe0d:bee1/64 scope link
valid_lft forever preferred_lft forever
root@OpenWrt:/#
|
