Adtran Bluesocket BSAP-2030

From TechInfoDepot
Jump to navigationJump to search
abgn+ac (AC1750)
Bluesocket 2030 802.11ac Indoor AP
1700950F1.jpg
Homepage
3rd Party Firmware
dd-wrt
Status Unknown
OpenWrt
Status Unknown
Tomato any flavor
Incompatible
Platform
Brand • Model • Rev
Adtran Bluesocket BSAP-2030 (1700948F1)
FCC ID
IC ID
Board ID
7016A0712004
Type
enterprise access point
CPU1
Freescale (NXP) P1010E
CPU1 Type
Power ISA
CPU1 Speed
1.0 GHz
Flash1 Chip
Spansion FL512SAIF01
Flash1 Size
64 MiB67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br />
RAM1 Size
256 MiB268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br />
RAM1 Chip
Samsung K4B1G1646G-BCH9 x 2
ETH chip1
Atheros AR8035-A
ETH chip2
Atheros AR8033-AL1A
Ethernet Port Count
2-1GbE-LAN
Wired Standard
IEEE 802.3i/3u/3ab

802dot11 OUI: 00:19:92 (4 E, 4 W), 88:DC:96 (20 E, 21 W)
Ethernet OUI: 00:19:92 (4 E, 4 W), 88:DC:96 (20 E, 21 W)

Stock FW OS
Linux 2.6.35
Expansion IF types
Mini PCIe, USB 2.0
Mini PCIe slots
2
USB ports
1
USB Hub Compatible
Untested
PoE
802.3af, standard
Power
12 VDC, 2 A
Connector type
barrel
Serial Port (UART)
yes, RJ45 console, (115200 8N1)
JTAG Port
yes, 16-pin header, EJTAG 1.2
Other

Default IP address: 192.168.190.1
the IP 192.168.190.1 is used by 4 additional devices
of which 4 are Adtran devices
Default login user: adm1n
Default login password: blue1socket
adm1n:blue1socket credentials used by 5 additional devices
of which 5 are Adtran devices

Manuf/OEM/ODM
Senao IAP7260 AG
Retail
FCC approval date 12 May 2014
Country of manuf Taiwan
Radio 1
Radio1 module
Radio1 module IF
Mini PCIe
Chip1
Qualcomm Atheros AR9590-AR1A
Wireless interface OUI
00:19:92, 88:DC:96,
Antenna Connector Type
U.FL
MIMO status
3x3:3
Wireless Standard
IEEE 802.11b/g/n
802.11n
up to 450 Mbps
802.11g
up to 54 Mbps
802.11b
up to 11 Mbps
WiFi Operating Frequency
2.4 GHz
Radio 2
Radio2 module
Radio2 module IF
Mini PCIe
Chip1
Qualcomm Atheros QCA9890-BR4A
Wireless interface OUI
00:19:92, 88:DC:96,
Antenna Connector Type
U.FL
MIMO status
3x3:3
Wireless Standard
IEEE 802.11a/n/ac
802.11ac
up to 1300 Mbps
802.11n
up to 450 Mbps
802.11a
up to 54 Mbps
WiFi Operating Frequency
5 GHz
 FCC ID
Extreme Networks AP3825eQXO-AP3825E
QXO-AP3715E
QXO-AP3715I
U2M-PCE3300AN
U2M-PCE4551AH
Extreme Networks WS-AP3825iQXO-AP3825E
QXO-AP3715E
QXO-AP3715I
U2M-PCE3300AN
U2M-PCE4551AH
 FCC ID
Senao PCE3300AHU2M-PCE3200AH
U2M-PCE3300AN

For a list of all currently documented Atheros (QCA) chipsets with specifications, see Atheros.
For a list of all currently documented Freescale (NXP) SoC's with specifications, see Freescale.
For a list of all currently documented Qualcomm Atheros (QCA) chipsets with specifications, see Qualcomm Atheros.

For a list of all currently documented Adtran device with specifications, see Adtran.

• 1300 Mbps - 3SS 5GHz 802.11ac (80MHz chan.),
• 450 Mbps - 3SS 2.4GHz 802.11n (40MHz chan.) = AC1750 class

Overview

  • Silkscreen on the PCB reads 7016A0747004 Ver:1.00, per User:Slimey
See also: Senao PCE3300AN, Senao PCE4553AH and Senao
(Senao IAP7260AG - int. ant., Senao IAP7261AG - ext. ant.)
QCA9890-BR4A + Skyworks (Sige) SE5003L1 (5GHz)
AR9590-AR1A + Skyworks (Sige) SE2595L (2.4GHz)
OUI: 88:DC:96

JTAG-Serial Info

JTAG

16-pin header, EJTAG 1.2

Serial

Serial info

Boot log

stock boot messages 
U-Boot 2010.12-00050-ga7f6f23 (Oct 02 2013 - 15:23:12)

CPU:   P1010E, Version: 1.0, (0x80f90010)
Core:  E500, Version: 5.1, (0x80212151)
Clock Configuration:
       CPU0:1000 MHz, 
       CCB:400  MHz,
       DDR:333.333 MHz (666.667 MT/s data rate) (Asynchronous), IFC:100  MHz
L1:    D-cache 32 kB enabled
       I-cache 32 kB enabled
Board: P1010RDB 
I2C:   ready
SPI:   ready
DRAM:  256 MiB (DDR3, 32-bit, CL=5, ECC off)
L2:    256 KB enabled
SF: Detected S25FL512S_256K with page size 256, total 64 MiB
No valid address in Flash. Using generated address
PCIe1: Root Complex of Mini PCIe Slot, x1, regs @ 0xffe0a000
  01:00.0     - 168c:003c - Network controller
PCIe1: Bus 00 - 01
PCIe2: Root Complex of PCIe Slot, x1, regs @ 0xffe09000
  03:00.0     - 168c:0033 - Network controller
PCIe2: Bus 02 - 03
In:    serial
Out:   serial
Err:   serial
Net:   eTSEC1, eTSEC2
Adtran bootloader version 1.0.5
SF: Detected S25FL512S_256K with page size 256, total 64 MiB
SF: Detected S25FL512S_256K with page size 256, total 64 MiB
Erasing SPI flash...Writing to SPI flash...done
SF: Detected S25FL512S_256K with page size 256, total 64 MiB
65536 KiB S25FL512S_256K at 0:0 is now current device
## Booting kernel from Legacy Image at 02000000 ...
   Image Name:   Linux Kernel Image
   Created:      2018-06-11  20:56:22 UTC
   Image Type:   PowerPC Linux Kernel Image (lzma compressed)
   Data Size:    1836021 Bytes = 1.8 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 00c00000
   Booting using the fdt blob at 0xc00000
   Uncompressing Kernel Image ... OK
   Loading Device Tree to 00ffb000, end 00fffeb3 ... OK
Using P1010 RDB machine description
Memory CAM mapping: 256 Mb, residual: 0Mb
Linux version 2.6.35 (root@jenkins24-hsv) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-55) ) #1 Mon Jun 11 20:56:09 UTC 2018
bootconsole [udbg0] enabled
setup_arch: bootmem
p1010_rdb_setup_arch()
Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->255
PCI host bridge /pcie@ffe09000  ranges:
 MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000a0000000 
  IO 0x00000000ffc10000..0x00000000ffc1ffff -> 0x0000000000000000
/pcie@ffe09000: PCICSRBAR @ 0xfff00000
Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->255
PCI host bridge /pcie@ffe0a000  ranges:
 MEM 0x0000000080000000..0x000000009fffffff -> 0x0000000080000000 
  IO 0x00000000ffc00000..0x00000000ffc0ffff -> 0x0000000000000000
/pcie@ffe0a000: PCICSRBAR @ 0xfff00000
P1010 RDB board from Freescale Semiconductor
arch: exit
Zone PFN ranges:
  DMA      0x00000000 -> 0x00010000
  Normal   empty
  HighMem  empty
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00010000
MMU: Allocated 1088 bytes of context maps for 255 contexts
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
Kernel command line: root=31:08 rw rootfstype=jffs2 console=ttyS0,115200
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 254528k/262144k available (4900k kernel code, 7616k reserved, 244k data, 138k bss, 176k init)
Kernel virtual memory layout:
  * 0xfffcf000..0xfffff000  : fixmap
  * 0xff800000..0xffc00000  : highmem PTEs
  * 0xff7d8000..0xff800000  : early ioremap
  * 0xd1000000..0xff7d8000  : vmalloc & ioremap
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
	RCU-based detection of stalled CPUs is disabled.
	Verbose stalled-CPUs detection is disabled.
NR_IRQS:512
mpic: Setting up MPIC " OpenPIC  " version 1.2 at ffe40000, max 1 CPUs
mpic: ISU size: 256, shift: 8, mask: ff
mpic: Initializing for 256 sources
clocksource: timebase mult[5000000] shift[22] registered
Console: colour dummy device 80x25
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
xor: measuring software checksum speed
   8regs     :  1227.000 MB/sec
   8regs_prefetch:  1057.000 MB/sec
   32regs    :  1221.000 MB/sec
   32regs_prefetch:  1086.000 MB/sec
xor: using function: 8regs (1227.000 MB/sec)
NET: Registered protocol family 16
             
e500 family performance monitor hardware support registered
GPIO initing mpc8572 cfffe04c
PCI: Probing PCI hardware
pci 0000:00:00.0: ignoring class b20 (doesn't match header type 01)
pci 0000:00:00.0: PCI bridge to [bus 01-ff]
pci 0001:02:00.0: ignoring class b20 (doesn't match header type 01)
pci 0001:02:00.0: PCI bridge to [bus 03-ff]
pci 0000:01:00.0: BAR 6: assigned [mem 0xa0020000-0xa002ffff pref]
pci 0000:00:00.0: not setting up bridge for bus 0000:01
pci 0001:03:00.0: BAR 6: can't assign mem pref (size 0x10000)
pci 0001:02:00.0: not setting up bridge for bus 0001:03
bio: create slab <bio-0> at 0
Freescale Elo / Elo Plus DMA driver
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource timebase
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
fsl-elo-dma ffe21300.dma: #0 (fsl,eloplus-dma-channel), irq 20
fsl-elo-dma ffe21300.dma: #1 (fsl,eloplus-dma-channel), irq 21
fsl-elo-dma ffe21300.dma: #2 (fsl,eloplus-dma-channel), irq 22
fsl-elo-dma ffe21300.dma: #3 (fsl,eloplus-dma-channel), irq 23
Slow work thread pool: Starting up
Slow work thread pool: Ready
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
msgmni has been set to 497
alg: No test for stdrng (krng)
async_tx: api initialized (async)
io scheduler noop registered
io scheduler deadline registered (default)
Null function/null data passed to tasklet
Generic non-volatile memory driver v1.1
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42) is a 16550A
brd: module loaded
loop: module loaded
fsl-espi ffe07000.spi: at 0xd110e000 (irq = 59)
registering panic_write to support mtdoops
m25p80 spi32766.0: s25fl512s (65536 Kbytes)
Creating 15 MTD partitions on "spi32766.0":
0x000000000000-0x000000040000 : "Bootloader"
0x000000040000-0x000000080000 : "Bootloader environment"
0x000000080000-0x0000000c0000 : "Cert"
0x0000000c0000-0x000000240000 : "Kdump"
mtdoops: Attached to MTD device 3
0x000000240000-0x000000640000 : "/var"
0x000000640000-0x0000008c0000 : "Kernel A"
0x0000008c0000-0x0000020c0000 : "Rootfs A"
0x0000020c0000-0x000002340000 : "Kernel B"
0x000002340000-0x000003b40000 : "Rootfs B"
0x000003b40000-0x000003c80000 : "/home"
0x000003c80000-0x000003e80000 : "/log"
0x000003e80000-0x000003ec0000 : "DTB A"
0x000003ec0000-0x000003f00000 : "DTB B"
0x000003fc0000-0x000004000000 : "ART"
0x000003f80000-0x000003fc0000 : "SENA0"
Fixed MDIO Bus: probed
e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k4
e1000e: Copyright (c) 1999 - 2009 Intel Corporation.
/proc/ptp_1588 created 

IEEE1588: ptp-timer devicepresent in the system
IEEE1588: ptp-timer initialized
eth0: Gianfar Ethernet Controller Version 1.4-skbr1.1.5, 00:19:92:xx:xx:xx
eth0: Running with NAPI enabled
eth0: RX BD ring size for Q[0]: 128
eth0: RX BD ring size for Q[1]: 128
eth0: RX BD ring size for Q[2]: 128
eth0: RX BD ring size for Q[3]: 128
eth0: RX BD ring size for Q[4]: 128
eth0: RX BD ring size for Q[5]: 128
eth0: RX BD ring size for Q[6]: 128
eth0: RX BD ring size for Q[7]: 128
eth0: TX BD ring size for Q[0]: 128
eth0: TX BD ring size for Q[1]: 128
eth0: TX BD ring size for Q[2]: 128
eth0: TX BD ring size for Q[3]: 128
eth0: TX BD ring size for Q[4]: 128
eth0: TX BD ring size for Q[5]: 128
eth0: TX BD ring size for Q[6]: 128
eth0: TX BD ring size for Q[7]: 128
Freescale PowerQUICC MII Bus: probed
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
i2c /dev entries driver
PowerPC Book-E Watchdog Timer Loaded
caam ffe30000.crypto: device ID = 0x0a14010000000000
caam ffe30000.crypto: job queues = 4
alg: No test for authenc(hmac(sha1),cbc(aes)) (authenc-hmac-sha1-cbc-aes-caam)
caam ffe30000.crypto: authenc-hmac-sha1-cbc-aes-caam
alg: No test for authenc(hmac(sha256),cbc(aes)) (authenc-hmac-sha256-cbc-aes-caam)
caam ffe30000.crypto: authenc-hmac-sha256-cbc-aes-caam
alg: No test for authenc(hmac(sha1),cbc(des3_ede)) (authenc-hmac-sha1-cbc-des3_ede-caam)
caam ffe30000.crypto: authenc-hmac-sha1-cbc-des3_ede-caam
alg: No test for authenc(hmac(sha256),cbc(des3_ede)) (authenc-hmac-sha256-cbc-des3_ede-caam)
caam ffe30000.crypto: authenc-hmac-sha256-cbc-des3_ede-caam
alg: No test for authenc(hmac(sha1),cbc(des)) (authenc-hmac-sha1-cbc-des-caam)
caam ffe30000.crypto: authenc-hmac-sha1-cbc-des-caam
alg: No test for authenc(hmac(sha256),cbc(des)) (authenc-hmac-sha256-cbc-des-caam)
caam ffe30000.crypto: authenc-hmac-sha256-cbc-des-caam
NET: Registered protocol family 26
TCP cubic registered
netfilter_table_index_init_early:init ok
MAXLINES_OF_TABLE:8
NET: Registered protocol family 10
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
JFFS2 notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
VFS: Mounted root (jffs2 filesystem) on device 31:8.
Freeing unused kernel memory: 176k init

Boot Bank: B Count: 1
A: 3.0.1-HB-646847 B: 3.3.0-527154

Serial: 2030xxxxxxxxxx
MAC: 00:19:92:xx:xx:xx

===========================
Access Point Console (2030)
===========================
User Access verification


bsap2030 login:

Boot log

OpenWrt boot messages WIP 
U-Boot 2010.12-00050-ga7f6f23 (Oct 02 2013 - 15:23:12)

CPU:   P1010E, Version: 1.0, (0x80f90010)
Core:  E500, Version: 5.1, (0x80212151)
Clock Configuration:
       CPU0:1000 MHz,
       CCB:400  MHz,
       DDR:333.333 MHz (666.667 MT/s data rate) (Asynchronous), IFC:100  MHz
L1:    D-cache 32 kB enabled
       I-cache 32 kB enabled
Board: P1010RDB
I2C:   ready
SPI:   ready
DRAM:  256 MiB (DDR3, 32-bit, CL=5, ECC off)
L2:    256 KB enabled
SF: Detected S25FL512S_256K with page size 256, total 64 MiB
No valid address in Flash. Using generated address
PCIe1: Root Complex of Mini PCIe Slot, x1, regs @ 0xffe0a000
  01:00.0     - 168c:003c - Network controller
PCIe1: Bus 00 - 01
PCIe2: Root Complex of PCIe Slot, x1, regs @ 0xffe09000
  03:00.0     - 168c:0033 - Network controller
PCIe2: Bus 02 - 03
In:    serial
Out:   serial
Err:   serial
Net:   eTSEC1, eTSEC2
Adtran bootloader version 1.0.5
SF: Detected S25FL512S_256K with page size 256, total 64 MiB
SF: Detected S25FL512S_256K with page size 256, total 64 MiB
Erasing SPI flash...Writing to SPI flash...done
2030 >
2030 > printenv
autostart=no
baudrate=115200
boot_bank=A
bootargs=root=31:06 rw rootfstype=jffs2 console=ttyS0,115200
bootcmd=sf probe 0; sf read 0x2000000 0x640000 0x280000; sf read 0xc00000 0x3E80000 0x40000; bootm 0x2000000 - 0xc00000
bootcnt=0
bootdelay=3
bootfile=uImage
consoledev=ttyS0
ethact=eTSEC1
ethaddr=00:19:92:xx:xx:xx
fdtaddr=c00000
fwversion_a=2.3-2030-1010.1-3.3.0-656804
fwversion_b=2.3-2030-1010.1-3.2.0-HA-650478
hostname=P1010RDB
loadaddr=1000000
mac_addr=00:19:92:xx:xx:xx
mfg_state=132
netdev=eth0
netretry=no
serial_num=2030xxxxxxxxxx
ver_num=1.0.5

Environment size: 600/262140 bytes
2030 > setenv serverip 192.168.1.2
2030 > setenv ipaddr 192.168.1.1
2030 > saveenv
Saving Environment to SPI Flash...
Erasing SPI flash...Writing to SPI flash...done
2030 > printenv
autostart=no
baudrate=115200
boot_bank=A
bootargs=root=31:06 rw rootfstype=jffs2 console=ttyS0,115200
bootcmd=sf probe 0; sf read 0x2000000 0x640000 0x280000; sf read 0xc00000 0x3E80000 0x40000; bootm 0x2000000 - 0xc00000
bootcnt=0
bootdelay=3
bootfile=uImage
consoledev=ttyS0
ethact=eTSEC1
ethaddr=00:19:92:xx:xx:xx
fdtaddr=c00000
fwversion_a=2.3-2030-1010.1-3.3.0-656804
fwversion_b=2.3-2030-1010.1-3.2.0-HA-650478
hostname=P1010RDB
ipaddr=192.168.1.1
loadaddr=1000000
mac_addr=00:19:92:xx:xx:xx
mfg_state=132
netdev=eth0
netretry=no
serial_num=2030xxxxxxxxxx
serverip=192.168.1.2
ver_num=1.0.5

Environment size: 644/262140 bytes
2030 > tftpboot openwrt-mpc85xx-generic-red-15w-rev1-initramfs-kernel.bin
Speed: 1000, full duplex
Using eTSEC1 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'openwrt-mpc85xx-generic-red-15w-rev1-initramfs-kernel.bin'.
Load address: 0x1000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ######################################
done
Bytes transferred = 5847676 (593a7c hex)
2030 > bootm 0x1000000
## Booting kernel from FIT Image at 01000000 ...
   Using 'config@1' configuration
   Trying 'kernel@1' kernel subimage
     Description:  POWERPC OpenWrt Linux-4.19.84
     Type:         Kernel Image
     Compression:  gzip compressed
     Data Start:   0x010000ec
     Data Size:    5834681 Bytes = 5.6 MiB
     Architecture: PowerPC
     OS:           Linux
     Load Address: 0x00000000
     Entry Point:  0x00000000
     Hash algo:    crc32
     Hash value:   0036693c
     Hash algo:    sha1
     Hash value:   e90b279a5a2ce964f00d5746bf9cc8607d809b25
   Verifying Hash Integrity ... crc32+ sha1+ OK
## Flattened Device Tree from FIT Image at 01000000
   Using 'config@1' configuration
   Trying 'fdt@1' FDT blob subimage
     Description:  POWERPC OpenWrt red-15w-rev1 device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x015909e8
     Data Size:    11102 Bytes = 10.8 KiB
     Architecture: PowerPC
     Hash algo:    crc32
     Hash value:   10ca102d
     Hash algo:    sha1
     Hash value:   9f9cc4268b20ac9931872490ee2ea612aa929916
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Booting using the fdt blob at 0x15909e8
   Uncompressing Kernel Image ... OK
   Loading Device Tree to 00ffa000, end 00fffb5d ... OK
[    0.000000] Memory CAM mapping: 256 Mb, residual: 0Mb
[    0.000000] Linux version 4.19.85 (builder@sunny) (gcc version 8.3.0 (OpenWrt GCC 8.3.0 r11562-08d9c95417)) #0 Sun Nov 24 22:17:34 2019
[    0.000000] Using P1010 RDB machine description
[    0.000000] bootconsole [udbg0] enabled
[    0.000000] -----------------------------------------------------
[    0.000000] phys_mem_size     = 0x10000000
[    0.000000] dcache_bsize      = 0x20
[    0.000000] icache_bsize      = 0x20
[    0.000000] cpu_features      = 0x0000000010010128
[    0.000000]   possible        = 0x0000000010010128
[    0.000000]   always          = 0x0000000000000020
[    0.000000] cpu_user_features = 0x84e08000 0x08000000
[    0.000000] mmu_features      = 0x00020010
[    0.000000] -----------------------------------------------------
red_15w_rev1_setup_arch()
[    0.000000] RED 15w Rev.1 from Sophos
[    0.000000] barrier-nospec: using isync; sync as speculation barrier
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[    0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 64960
[    0.000000] Kernel command line: root=31:06 rw rootfstype=jffs2 console=ttyS0,115200
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 182196K/262144K available (4632K kernel code, 204K rwdata, 1060K rodata, 5364K init, 213K bss, 79948K reserved, 0K cma-reserved)
[    0.000000] Kernel virtual memory layout:
[    0.000000]   * 0xfffdf000..0xfffff000  : fixmap
[    0.000000]   * 0xfdffe000..0xfe000000  : early ioremap
[    0.000000]   * 0xd1000000..0xfdffe000  : vmalloc & ioremap
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 512, nr_irqs: 512, preallocated irqs: 16
[    0.000000] mpic: Setting up MPIC " OpenPIC  " version 1.2 at ffe40000, max 1 CPUs
[    0.000000] mpic: ISU size: 256, shift: 8, mask: ff
[    0.000000] mpic: Initializing for 256 sources
[    0.000009] clocksource: timebase: mask: 0xffffffffffffffff max_cycles: 0xb8812736b, max_idle_ns: 440795202655 ns
[    0.010180] clocksource: timebase mult[14000000] shift[24] registered
[    0.016640] pid_max: default: 32768 minimum: 301
[    0.021364] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.027892] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.037220] random: get_random_u32 called from bucket_table_alloc.isra.21+0x148/0x1ac with crng_init=0
[    0.046688] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.056350] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.062685] NET: Registered protocol family 16

[    0.073248] Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->255
[    0.081270] PCI host bridge /pcie@ffe0a000 (primary) ranges:
[    0.086897]  MEM 0x0000000080000000..0x000000009fffffff -> 0x0000000080000000
[    0.094098]   IO 0x00000000ffc00000..0x00000000ffc0ffff -> 0x0000000000000000
[    0.101229] /pcie@ffe0a000: PCICSRBAR @ 0xfff00000
[    0.105988] setup_pci_atmu: end of DRAM 10000000
[    0.118528] PCI: Probing PCI hardware
[    0.122230] fsl-pci ffe0a000.pcie: PCI host bridge to bus a000:00
[    0.128254] pci_bus a000:00: root bus resource [io  0x0000-0xffff]
[    0.134398] pci_bus a000:00: root bus resource [mem 0x80000000-0x9fffffff]
[    0.141256] pci_bus a000:00: root bus resource [bus 00-ff]
[    0.159475] pci a000:00:00.0: PCI bridge to [bus 01-ff]
[    0.164750] PCI: Cannot allocate resource region 0 of device a000:00:00.0, will remap
[    0.172527] pci a000:00:00.0: BAR 0: no space for [mem size 0x00100000]
[    0.179089] pci a000:00:00.0: BAR 0: failed to assign [mem size 0x00100000]
[    0.186037] pci a000:01:00.0: BAR 6: assigned [mem 0x80200000-0x8020ffff pref]
[    0.193237] pci a000:00:00.0: PCI bridge to [bus 01]
[    0.198183] pci a000:00:00.0:   bridge window [io  0x0000-0xffff]
[    0.204260] pci a000:00:00.0:   bridge window [mem 0x80000000-0x9fffffff]
[    0.211029] pci_bus a000:00: Some PCI device resources are unassigned, try booting with pci=realloc
[    0.220154] /soc@ffe00000/timer@41100: cannot get timer frequency.
[    0.226283] /soc@ffe00000/timer@42100: cannot get timer frequency.
[    0.237794] fsl-ifc ffe1e000.ifc: Freescale Integrated Flash Controller
[    0.244366] fsl-ifc ffe1e000.ifc: IFC version 1.0, 4 banks
[    0.251388] clocksource: Switched to clocksource timebase
[    0.257211] NET: Registered protocol family 2
[    0.261834] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes)
[    0.269436] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    0.276365] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.282694] TCP: Hash tables configured (established 2048 bind 2048)
[    0.289078] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.294850] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.301217] NET: Registered protocol family 1
[    5.045941] Crashlog allocated RAM at address 0x3f00000
[    5.051770] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[    5.061952] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    5.067728] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    5.084567] io scheduler noop registered
[    5.088422] io scheduler deadline registered (default)
[    5.107531] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[    5.114144] console [ttyS0] disabled
[    5.117672] serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42, base_baud = 24999999) is a 16550A
[    5.126330] console [ttyS0] enabled
[    5.126330] console [ttyS0] enabled
[    5.133259] bootconsole [udbg0] disabled
[    5.133259] bootconsole [udbg0] disabled
[    5.141318] serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42, base_baud = 24999999) is a 16550A
[    5.150484] console [ttyS0] disabled
[    5.154111] console [ttyS0] enabled
[    5.157934] ffe04600.serial: ttyS1 at MMIO 0xffe04600 (irq = 42, base_baud = 24999999) is a 16550
[    5.167287] fsl,ifc-nand ff800000.nand: fsl_ifc_nand_probe: address did not match any chip selects
[    5.210063] fsl_espi ffe07000.spi: at 0x(ptrval) (irq = 59)
[    5.215943] libphy: Fixed MDIO Bus: probed
[    5.220501] libphy: Freescale PowerQUICC MII Bus: probed
[    5.225991] mdio_bus mdio@ffe24000: MDIO device at address 0 is missing.
[    5.232799] libphy: Freescale PowerQUICC MII Bus: probed
[    5.256060] fsl-gianfar soc@ffe00000:ethernet@b0000: enabled errata workarounds, flags: 0x4
[    5.274872] fsl-gianfar soc@ffe00000:ethernet@b0000 eth0: mac: 00:19:92:xx:xx:xx
[    5.282277] fsl-gianfar soc@ffe00000:ethernet@b0000 eth0: Running with NAPI enabled
[    5.289932] fsl-gianfar soc@ffe00000:ethernet@b0000 eth0: RX BD ring size for Q[0]: 256
[    5.297933] fsl-gianfar soc@ffe00000:ethernet@b0000 eth0: TX BD ring size for Q[0]: 256
[    5.306152] fsl-gianfar soc@ffe00000:ethernet@b1000: enabled errata workarounds, flags: 0x4
[    5.324814] fsl-gianfar soc@ffe00000:ethernet@b1000 eth1: mac: 00:00:00:00:00:00
[    5.332219] fsl-gianfar soc@ffe00000:ethernet@b1000 eth1: Running with NAPI enabled
[    5.339874] fsl-gianfar soc@ffe00000:ethernet@b1000 eth1: RX BD ring size for Q[0]: 256
[    5.347875] fsl-gianfar soc@ffe00000:ethernet@b1000 eth1: TX BD ring size for Q[0]: 256
[    5.355977] ucc_geth_driver: QE UCC Gigabit Ethernet Controller
[    5.362154] mpc-i2c ffe03000.i2c: timeout 1000000 us
[    5.367293] mpc-i2c ffe03100.i2c: timeout 1000000 us
[    5.372504] booke_wdt: powerpc book-e watchdog driver loaded
[    5.378690] NET: Registered protocol family 10
[    5.385544] Segment Routing with IPv6
[    5.389281] NET: Registered protocol family 17
[    5.393754] 8021q: 802.1Q VLAN Support v1.8
[    5.397977] drmem: No dynamic reconfiguration memory found
[    5.404836] hctosys: unable to open rtc device (rtc0)
[    5.420591] Freeing unused kernel memory: 5364K
[    5.425193] Run /init as init process
[    5.448878] init: Console is alive
[    5.452430] init: - watchdog -
[    5.462937] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    5.477387] usbcore: registered new interface driver usbfs
[    5.482937] usbcore: registered new interface driver hub
[    5.488305] usbcore: registered new device driver usb
[    5.495969] Button Hotplug driver version 0.4.1
[    5.501853] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.514410] SCSI subsystem initialized
[    5.520933] ehci-fsl: Freescale EHCI Host controller driver
[    5.527439] ehci-platform: EHCI generic platform driver
[    5.533673] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[    5.540336] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[    5.557609] fsl-ehci fsl-ehci.0: irq 28, io mem 0xffe22000
[    5.575398] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[    5.581384] hub 1-0:1.0: USB hub found
[    5.585323] hub 1-0:1.0: 1 port detected
[    5.590299] ehci-pci: EHCI PCI platform driver
[    5.596447] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    5.603325] ohci-platform: OHCI generic platform driver
[    5.610108] uhci_hcd: USB Universal Host Controller Interface driver
[    5.617306] ohci-pci: OHCI PCI platform driver
[    5.633272] usbcore: registered new interface driver usb-storage
[    5.640498] usbcore: registered new interface driver uas
[    5.646201] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.656172] init: - preinit -
[    5.716455] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    5.722617] random: procd: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    6.727420] fsl-gianfar soc@ffe00000:ethernet@b0000 eth0: Link is Up - 1Gbps/Full - flow control off
[    6.736580] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    8.804979] procd: - early -
[    8.808318] procd: - watchdog -
[    9.560920] procd: - watchdog -
[    9.564222] procd: - ubus -
[    9.569647] random: ubusd: uninitialized urandom read (4 bytes read)
[    9.616777] random: ubusd: uninitialized urandom read (4 bytes read)
[    9.623327] random: ubusd: uninitialized urandom read (4 bytes read)
[    9.630149] procd: - init -
Please press Enter to activate this console.
[    9.826812] kmodloader: loading kernel modules from /etc/modules.d/*
[    9.859541] Loading modules backported from Linux version v5.4-rc8-0-gaf42d3466bdc
[    9.867124] Backport generated by backports.git v5.4-rc8-1-0-g368e8c51
[    9.902187] usbcore: registered new interface driver ums-alauda
[    9.915979] usbcore: registered new interface driver ums-cypress
[    9.928039] usbcore: registered new interface driver ums-datafab
[    9.943942] usbcore: registered new interface driver ums-freecom
[    9.956049] usbcore: registered new interface driver ums-isd200
[    9.972027] usbcore: registered new interface driver ums-jumpshot
[    9.983963] usbcore: registered new interface driver ums-karma
[   10.000197] usbcore: registered new interface driver ums-sddr09
[   10.012134] usbcore: registered new interface driver ums-sddr55
[   10.024131] usbcore: registered new interface driver ums-usbat
[   10.048525] xt_time: kernel timezone is -0000
[   10.069102] urngd: v1.0.1 started.
[   10.150136] PPP generic driver version 2.4.2
[   10.163931] NET: Registered protocol family 24
[   10.221833] ath10k_pci a000:01:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[   10.244979] random: crng init done
[   10.248387] random: 6 urandom warning(s) missed due to ratelimiting
[   10.454192] firmware ath10k!pre-cal-pci-a000:01:00.0.bin: firmware_loading_store: map pages failed
[   10.506217] firmware ath10k!cal-pci-a000:01:00.0.bin: firmware_loading_store: map pages failed
[   10.557664] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[   10.567785] ath10k_pci a000:01:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[   10.577026] ath10k_pci a000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[   10.587322] ath10k_pci a000:01:00.0: firmware ver 10.2.4-1.0-00047 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 35bd9258
[   10.674219] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[   10.683171] ath10k_pci a000:01:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[   10.791376] ath10k_pci a000:01:00.0: otp calibration failed: 2
[   10.797221] ath10k_pci a000:01:00.0: failed to run otp: -22
[   10.802793] ath10k_pci a000:01:00.0: could not init core (-22)
[   10.808663] ath10k_pci a000:01:00.0: could not probe fw (-22)
[   10.835973] kmodloader: done loading kernel modules from /etc/modules.d/*
[   23.997703] br-lan: port 1(eth0) entered blocking state
[   24.002965] br-lan: port 1(eth0) entered disabled state
[   24.008374] device eth0 entered promiscuous mode
[   24.063456] br-lan: port 1(eth0) entered blocking state
[   24.068693] br-lan: port 1(eth0) entered forwarding state
[   24.074203] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   24.999413] fsl-gianfar soc@ffe00000:ethernet@b0000 eth0: Link is Up - 1Gbps/Full - flow control off
[   25.008735] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready



BusyBox v1.31.1 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt SNAPSHOT, r11591-c5497ebb1c
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel master br-lan state UP qlen 1000
    link/ether 00:19:92:xx:xx:xx brd ff:ff:ff:ff:ff:ff
3: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
4: br-lan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP qlen 1000
    link/ether 00:19:92:xx:xx:xx brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.1/24 brd 192.168.1.255 scope global br-lan
       valid_lft forever preferred_lft forever
    inet6 fd6c:5ac0:17e7::1/60 scope global
       valid_lft forever preferred_lft forever
    inet6 fe80::219:92ff:fe3b:b120/64 scope link
       valid_lft forever preferred_lft forever

root@OpenWrt:/# lspci -vvvvv
a000:00:00.0 PCI bridge: Freescale Semiconductor Inc P1010 (rev 10) (prog-if 00 [Normal decode])
        Device tree node: /sys/firmware/devicetree/base/pcie@ffe0a000/pcie@0
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 32 bytes
        Interrupt: pin ? routed to IRQ 16
        Region 0: Memory at <ignored> (32-bit, non-prefetchable)
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        I/O behind bridge: 00000000-0000ffff [size=64K]
        Memory behind bridge: 80000000-9fffffff [size=512M]
        Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff [empty]
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [44] Power Management version 3
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [4c] Express (v2) Root Port (Slot-), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0
                        ExtTag- RBE+
                DevCtl: CorrErr- NonFatalErr+ FatalErr+ UnsupReq+
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
                LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s, Exit Latency L0s <2us
                        ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp-
                LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s (downgraded), Width x1 (ok)
                        TrErr- Train- SlotClk- DLActive- BWMgmt+ ABWMgmt-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
                DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd-
                         AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
                DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
                         AtomicOpsCtl: ReqEn- EgressBlck-
                LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
                         Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
                         Compliance De-emphasis: -6dB
                LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
                         EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
        Capabilities: [100 v1] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
                CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
                AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
                        MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
                HeaderLog: 00000000 00000000 00000000 00000000
                RootCmd: CERptEn- NFERptEn- FERptEn-
                RootSta: CERcvd- MultCERcvd- UERcvd- MultUERcvd-
                         FirstFatal- NonFatalMsg- FatalMsg- IntMsg 0
                ErrorSrc: ERR_COR: 0000 ERR_FATAL/NONFATAL: 0000
        Kernel driver in use: pcieport
lspci: Unable to load libkmod resources: error -12

a000:01:00.0 Network controller: Qualcomm Atheros QCA986x/988x 802.11ac Wireless Network Adapter
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 17
        Region 0: Memory at 80000000 (64-bit, non-prefetchable) [size=2M]
        [virtual] Expansion ROM at 80200000 [disabled] [size=64K]
        Capabilities: [40] Power Management version 3
                Flags: PMEClk- DSI- D1+ D2- AuxCurrent=375mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [50] MSI: Enable- Count=1/8 Maskable+ 64bit-
                Address: 00000000  Data: 0000
                Masking: 00000000  Pending: 00000000
        Capabilities: [70] Express (v2) Endpoint, MSI 00
                DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us
                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 15.000W
                DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr- TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <4us, L1 <64us
                        ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
                        TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported
                         AtomicOpsCap: 32bit- 64bit- 128bitCAS-
                DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
                         AtomicOpsCtl: ReqEn-
                LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
                         Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
                         Compliance De-emphasis: -6dB
                LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
                         EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
        Capabilities: [100 v1] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
                CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
                AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn- ECRCChkCap- ECRCChkEn-
                        MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
                HeaderLog: 00000000 00000000 00000000 00000000
        Capabilities: [140 v1] Virtual Channel
                Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
                Arb:    Fixed- WRR32- WRR64- WRR128-
                Ctrl:   ArbSelect=Fixed
                Status: InProgress-
                VC0:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
                        Status: NegoPending- InProgress-
        Capabilities: [160 v1] Device Serial Number 00-00-00-00-00-00-00-00
        Kernel driver in use: ath10k_pci


root@OpenWrt:/# lsusb -tvvv
/:  Bus 01.Port 1: Dev 1, Class=root_hub, Driver=fsl-ehci/1p, 480M

root@OpenWrt:/# lspci -Gkxvvvvvvvv
Trying method linux-sysfs......using /sys/bus/pci...OK
Decided to use linux-sysfs
a000:00:00.0 PCI bridge: Freescale Semiconductor Inc P1010 (rev 10) (prog-if 00 [Normal decode])
        Device tree node: /sys/firmware/devicetree/base/pcie@ffe0a000/pcie@0
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 32 bytes
        Interrupt: pin ? routed to IRQ 16
        Region 0: Memory at <ignored> (32-bit, non-prefetchable)
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        I/O behind bridge: 00000000-0000ffff [size=64K]
        Memory behind bridge: 80000000-9fffffff [size=512M]
        Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff [empty]
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA- VGA- VGA16- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [44] Power Management version 3
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [4c] Express (v2) Root Port (Slot-), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0
                        ExtTag- RBE+
                DevCtl: CorrErr- NonFatalErr+ FatalErr+ UnsupReq+
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
                LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s, Exit Latency L0s <2us
                        ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp-
                LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s (downgraded), Width x1 (ok)
                        TrErr- Train- SlotClk- DLActive- BWMgmt+ ABWMgmt-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
                DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd-
                         AtomicOpsCap: Routing- 32bit- 64bit- 128bitCAS-
                DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
                         AtomicOpsCtl: ReqEn- EgressBlck-
                LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
                         Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
                         Compliance De-emphasis: -6dB
                LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
                         EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
        Capabilities: [100 v1] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
                CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
                AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
                        MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
                HeaderLog: 00000000 00000000 00000000 00000000
                RootCmd: CERptEn- NFERptEn- FERptEn-
                RootSta: CERcvd- MultCERcvd- UERcvd- MultUERcvd-
                         FirstFatal- NonFatalMsg- FatalMsg- IntMsg 0
                ErrorSrc: ERR_COR: 0000 ERR_FATAL/NONFATAL: 0000
        Kernel driver in use: pcieport
lspci: Unable to load libkmod resources: error -12
00: 57 19 28 01 07 01 10 00 10 00 20 0b 08 00 01 00
10: 00 00 f0 ff 00 00 00 00 00 01 01 00 01 f1 00 20
20: 00 80 f0 9f f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 44 00 00 00 00 00 00 00 00 00 00 00

a000:01:00.0 Network controller: Qualcomm Atheros QCA986x/988x 802.11ac Wireless Network AdapterUsing cache /root/.pciids-cache
Cache file does not exist

        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 17
        Region 0: Memory at 80000000 (64-bit, non-prefetchable) [size=2M]
        [virtual] Expansion ROM at 80200000 [disabled] [size=64K]
        Capabilities: [40] Power Management version 3
                Flags: PMEClk- DSI- D1+ D2- AuxCurrent=375mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [50] MSI: Enable- Count=1/8 Maskable+ 64bit-
                Address: 00000000  Data: 0000
                Masking: 00000000  Pending: 00000000
        Capabilities: [70] Express (v2) Endpoint, MSI 00
                DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us
                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 15.000W
                DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr- TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <4us, L1 <64us
                        ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
                        TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported
                         AtomicOpsCap: 32bit- 64bit- 128bitCAS-
                DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
                         AtomicOpsCtl: ReqEn-
                LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
                         Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
                         Compliance De-emphasis: -6dB
                LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
                         EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
        Capabilities: [100 v1] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
                CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
                AERCap: First Error Pointer: 00, ECRCGenCap- ECRCGenEn- ECRCChkCap- ECRCChkEn-
                        MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
                HeaderLog: 00000000 00000000 00000000 00000000
        Capabilities: [140 v1] Virtual Channel
                Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
                Arb:    Fixed- WRR32- WRR64- WRR128-
                Ctrl:   ArbSelect=Fixed
                Status: InProgress-
                VC0:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
                        Status: NegoPending- InProgress-
        Capabilities: [160 v1] Device Serial Number 00-00-00-00-00-00-00-00
        Kernel driver in use: ath10k_pci
00: 8c 16 3c 00 06 00 10 00 00 00 80 02 08 00 00 00
10: 04 00 00 80 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 ff 01 00 00



root@OpenWrt:/# cat /proc/cpuinfo
processor       : 0
cpu             : e500v2
clock           : 999.999990MHz
revision        : 5.1 (pvr 8021 2151)
bogomips        : 100.00

timebase        : 50000000
platform        : P1010 RDB
model           : Sophos RED 15w Rev.1
Memory          : 256 MB

root@OpenWrt:/# cat /proc/devices
Character devices:
  1 mem
  2 pty
  3 ttyp
  4 ttyS
  5 /dev/tty
  5 /dev/console
  5 /dev/ptmx
 10 misc
 13 input
 90 mtd
108 ppp
128 ptm
136 pts
180 usb
189 usb_device
252 watchdog
253 rtc
254 gpiochip

Block devices:
 31 mtdblock
254 ubiblock
259 blkext


See also

Products

Bluesocket Family Access Points
Retrieved from "https://techinfodepot.shoutwiki.com/w/index.php?title=Adtran_Bluesocket_BSAP-2030&oldid=386569"