Allnet ALL-WAP02860AC

abgn+ac (AC1750)
802.11ac 3x3 Indoor Access Point
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	Allnet ALL-WAP02860AC
FCC ID	none specified
Type	access point
CPU1 Y	Qualcomm Atheros QCA9558
CPU1 Type	MIPS 74Kc
CPU1 Speed	720 MHz
Flash1 Chip	Brand? Model?
Flash1 Size	16 MiB 16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br />
RAM1 Size	128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br />
RAM1 Chip	Brand? Model?
ETH chip1	Qualcomm Atheros QCA9558
Ethernet Port Count	1-1GbE-LAN
Wired Standard	IEEE 802.3i/3u/3ab
802dot11 OUI: none specified
Stock bootloader	U-Boot
Expansion IF types	Mini PCIe
Mini PCIe slots	1
PoE	802.3at, standard
Power	12 VDC, 2 A
Serial Port (UART)	yes, (115200 8N1)
Other
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Retail
Availability	End of Life
Radio 1
Chip1	Qualcomm Atheros QCA9558
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	3x3:3
Wireless Standard	IEEE 802.11b/g/n
802.11n	up to 450 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
Radio 2
Chip1	Qualcomm Atheros QCA9880
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	3x3:3
Wireless Standard	IEEE 802.11a/n/ac
802.11ac	up to 1300 Mbps
802.11n	up to 450 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz

For a list of all currently documented Qualcomm Atheros (QCA) chipsets with specifications, see Qualcomm Atheros.

For a list of all currently documented Allnet devices with specifications, see Allnet.

• 450 Mbps - 3SS 2.4GHz 802.11n (40MHz chan.),

• 1300 Mbps - 3SS 5GHz 802.11ac (80MHz chan.) = AC1750 class

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)
On the OpenWrt Wiki

Target: ath79
Subtarget: generic
Package architecture: mips_24kc
Supported Since Commit
Support started version: 21.02.0
Current supported version: 25.12.5

WLAN Comment: Qualcomm Atheros QCA9558, Qualcomm Atheros QCA9880
Installation method(s):
unknown

git • >>

ath79: add support for ALLNET ALL-WAP02860AC ALLNET ALL-WAP02860AC is a dual-band wireless access point. Specification SoC: Qualcomm Atheros QCA9558 RAM: 128 MB DDR2 Flash: 16 MB SPI NOR WIFI: 2.4 GHz 3T3R integrated 5 GHz 3T3R QCA9880 Mini PCIe card Ethernet: 1x 10/100/1000 Mbps AR8035-A, PoE capable (802.3at) LEDS: 5x, which four are GPIO controlled Buttons: 1x GPIO controlled UART: 4 pin header near Mini PCIe card, starting count from white triangle on PCB 1. VCC 3.3V, 2. GND, 3. TX, 4. RX baud: 115200, parity: none, flow control: none MAC addresses Calibration data does not contain valid MAC addresses. The calculated MAC addresses are chosen in accordance with OEM firmware. Because of: a) constrained environment (SNMP) when connecting through Telnet or SSH, b) hard-coded kernel and rootfs sizes, c) checksum verification of kerenel and rootfs images in bootloder, creating factory image accepted by OEM web interface is difficult, therefore, to install OpenWrt on this device UART connection is needed. The teardown is simple, unscrew four screws to disassemble the casing, plus two screws to separate mainboard from the casing. Before flashing, be sure to have a copy of factory firmware, in case You wish to revert to original firmware. Installation 1. Prepare TFTP server with OpenWrt initramfs-kernel image. 2. Connect to LAN port. 3. Connect to UART port. 4. Power on the device and when prompted to stop autoboot, hit any key. 5. Alter U-Boot environment with following commands: setenv failsafe_boot bootm 0x9f0a0000 saveenv 6. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use 'setenv' to do that, then run following commands: tftpboot 0x81000000 <openwrt_initramfs-kernel_image_name> bootm 0x81000000 7. Wait about 1 minute for OpenWrt to boot. 8. Transfer OpenWrt sysupgrade image to /tmp directory and flash it with: sysupgrade -n /tmp/<openwrt_sysupgrade_image_name> 9. After flashing, the access point will reboot to OpenWrt. Wait few minutes, until the Power LED stops blinking, then it's ready for configuration.