Arcadyan VRV9510KWAC23
From TechInfoDepot
(Redirected from Arcadyan / Astoria VRV9510KWAC23)
Jump to navigationJump to searchabgn+ac (AC1600) | |
---|---|
Router Livebox Next | |
![]() | |
Homepage | |
3rd Party Firmware | |
dd-wrt |
Status Unknown |
OpenWrt | |
Tomato any flavor |
Incompatible |
Gargoyle |
Status Unknown |
Platform | |
Brand • Model • Rev |
Arcadyan VRV9510KWAC23 |
FCC ID |
none specified |
Type |
wireless router |
CPU1 ![]() |
Lantiq VRX288 |
CPU1 Type |
MIPS 34Kc |
CPU1 Speed |
500 MHz ( 2 cores ) |
Flash1 Chip |
Brand? Model? |
Flash1 Size |
128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (NAND) |
RAM1 Size |
256 MiB268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br /> (DDR2) |
RAM1 Chip |
Brand? Model? |
ETH chip1 |
Lantiq VRX288 |
Switch |
Lantiq VRX288 |
VOIP Ports |
2 |
Ethernet Port Count |
1-1GbE-WAN 5-1GbE-LAN |
Wired Standard |
IEEE 802.3i/3u/3ab |
802dot11 OUI: none specified | |
Stock bootloader |
brnboot |
Expansion IF types |
USB 2.0 |
USB ports |
2 |
USB Hub Compatible |
Untested |
Power |
12 VDC, 2.5 A |
Serial Port (UART) |
yes, 3.3, 115200 / 8N1 |
JTAG Port |
no |
Flags: VDSL/ADSL2+ | |
Other | |
| |
3rd Party Firmware Support | |
Retail | |
Availability | End of Life |
Radio 1 | |
Chip1 |
Broadcom BCM43222 |
Wireless interface OUI |
none specified |
Antenna Connector Type |
none specified |
MIMO status |
2x2:2 |
Wireless Standard |
IEEE 802.11b/g/n |
802.11n |
up to 300 Mbps |
802.11g |
up to 54 Mbps |
802.11b |
up to 11 Mbps |
WiFi Operating Frequency |
2.4 GHz |
Radio 2 | |
Chip1 |
Broadcom BCM4360 |
Wireless interface OUI |
none specified |
Antenna Connector Type |
none specified |
MIMO status |
3x3:3 |
Wireless Standard |
IEEE 802.11a/n/ac |
802.11ac |
up to 1300 Mbps |
802.11n |
up to 450 Mbps |
802.11a |
up to 54 Mbps |
WiFi Operating Frequency |
5 GHz |
Radio cor_rev |
40 |
For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.
For a list of all currently documented Lantiq (Intel) chipsets with specifications, see Lantiq.
For a list of all currently documented Arcadyan device with specifications, see Arcadyan.
Overview
Specs
- SoC: Lantiq VRX200
- CPU: 2x MIPS 34Kc 500 MHz
- RAM: 256 MiB DDR2
- Flash: 128 MiB NAND
- Ethernet: Built-in Gigabit Ethernet switch, 5x 1GbE
- Wifi 2.4GHz: Broadcom BCM43222KFBG 802.11b/g/b MIMO 2T2R
- Wifi 5GHz: Broadcom BCM4360KMLG 802.11ac MIMO 3T3R
- USB: 2x USB 2.0
- DSL: Built-in VDSL/ADSL2+ XWAY VRX208
- LEDs: 8x
- Buttons: 4x
- Phone: Lantiq PEF 42068 V XWAY SLIC120
Flashing
![]() | NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
![]() | Devices with Broadcom WiFi chipsets have limited OpenWrt supportability (due to limited FLOSS driver availability for Broadcom chips). Consider this when choosing a device to buy, or when deciding to flash OpenWrt on your device because it is listed as supported. See Broadcom WiFi for details. |
On the OpenWrt ToH (techdata entry)
On the OpenWrt Wiki
On the OpenWrt Forum
OpenWrt Target: lantiq
OpenWrt Subtarget: xrx200
OpenWrt Package architecture: mips_24kc
Support started version: 24.10.0
Current supported version: 24.10.0
Unsupported Functions:
WiFi 5GHz
On the OpenWrt Wiki
On the OpenWrt Forum
OpenWrt Target: lantiq
OpenWrt Subtarget: xrx200
OpenWrt Package architecture: mips_24kc
Support started version: 24.10.0
Current supported version: 24.10.0
Unsupported Functions:
WiFi 5GHz
Detailed instructions can be found on the wiki https://openwrt.org/toh/arcadyan/vrv9510kwac23
- Boot into UART mode and upload the the https://raw.githubusercontent.com/danielhuici/arcadyan-vrv9510kwac23-utils/main/u-boot.asc file via serial console to boot into U-Boot.
- Perform a backup of the NAND
- Setup a TFTP server and serve the https://github.com/danielhuici/arcadyan-vrv9510kwac23-utils/raw/main/u-boot.ltq.lzo.nandspl. Replace the OEM bootloader with this one. Erase your NAND and write the image into it
- Reboot the router
- Serve the OpenWrt ramdisk image on your TFTP server and boot it via U-Boot
- When OpenWrt boots, flash the SquashFS OpenWrt image using LuCi interface, so OpenWrt gets installed into the NAND
Categories:
- Arcadyan
- Embedded system/wireless router
- Embedded System Lantiq
- Embedded System VRX288
- Lantiq
- Embedded System MIPS 34Kc
- Embedded System
- OpenWrt Supported
- Embedded System Broadcom
- Embedded System BCM43222
- Broadcom
- Has Mimo Status
- Embedded System IEEE 802.11b/g/n
- Embedded System BCM4360
- Embedded System IEEE 802.11a/n/ac
- Dual-Radio Wireless Embedded System
- Wireless Embedded System
- Dual-Band
- English Documentation