Asante SmartHub AWRT-550N/Serial info

From TechInfoDepot
Jump to navigationJump to search

Info derived from

boot log


U-Boot 1.1.3 (Dec 31 2008 - 00:12:21)

Board: Ralink APSoC DRAM:  32 MB
relocate_code Pointer at: 81fa8000
flash_protect ON: from 0xBF000000 to 0xBF0250D3
protect on 0
protect on 1
protect on 2
protect on 3
protect on 4
protect on 5
protect on 6
protect on 7
protect on 8
protect on 9
flash_protect ON: from 0xBF030000 to 0xBF03FFFF
protect on 10
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version : 3.2
UBoot Release Version: 1.0.1_20081231
--------------------------------------------
ASIC 3052_MP2 (Port5<->None)
DRAM COMPONENT: 128Mbits
DRAM BUS: 32BIT
Total memory: 32 MBytes
Date:Dec 31 2008  Time:00:12:21
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384

 ##### The CPU freq = 384 MHZ ####

 SDRAM bus set to 32 bit
 SDRAM size =32 Mbytes

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   9: Load Boot Loader code then write to Flash via TFTP.                                                                                                0

3: System Boot system code via Flash.

 eth_register
Eth0 (10/100-M)
 enetvar=ethaddr,Eth addr:00:AA:BB:CC:DD:10
 00:AA:BB:CC:DD:10:

 eth_current->name = Eth0 (10/100-M)

## Booting image at bf050000 ...
   Image Name:   Linux Kernel Image
   Created:      2010-07-16   2:53:56 UTC

 System Control Status = 0x23440000
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1170627 Bytes =  1.1 MB
   Load Address: 80000000
   Entry Point:  8036c000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8036c000) ...
## Giving linux memsize in MB, 32

Starting kernel ...


LINUX started...

 THIS IS ASIC
Linux version 2.6.21 (terry_kuo@cvs4) (gcc version 3.4.2) #183 Fri Jul 16 10:49:36 CST 2010

 The CPU feqenuce set to 384 MHz
CPU revision is: 0001964c
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
Built 1 zonelists.  Total pages: 8128
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock2
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = 80800030, status = 1100ff00
PID hash table entries: 128 (order: 7, 512 bytes)
calculating r4koff... 00177000(1536000)
CPU frequency 384.00 MHz
Using 192.000 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 28724k/32768k available (2943k kernel code, 4044k reserved, 556k data, 132k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
NTFS driver 2.1.28 [Flags: R/O].
fuse init (API version 7.8)
io scheduler noop registered (default)
FLASH_API: MAN_ID=C2 DEV_ID=22CB SIZE=8MB
Ralink RT2880 gpio driver initialized
Gemtek LED init...
Ralink gpio driver initialized
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
ralink flash device: 0x1000000 at 0xbf000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 5 MTD partitions on "Ralink SoC physically mapped flash":
0x00000000-0x00050000 : "uboot"
0x00050000-0x007e0000 : "Kernel and Rootfs"
0x001b0000-0x007e0000 : "Rootfs"
0x007e0000-0x007f0000 : "Nvram"
0x007f0000-0x00800000 : "Factory"
block2mtd: version $Revision: 1.1.1.1 $
usbmon: debugfs is not available
116x: driver isp116x-hcd, 03 Nov 2005
sl811: driver sl811-hcd, 19 May 2005
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
dwc_otg: version 2.60a 22-NOV-2006
DWC_otg: Using DMA mode
dwc_otg lm0: DWC OTG Controller
dwc_otg lm0: new USB bus registered, assigned bus number 1
dwc_otg lm0: irq 18, io mem 0x00000000
DWC_otg: Init: Port Power? op_state=1
DWC_otg: Init: Power Port (0)
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
nf_conntrack version 0.5.0 (256 buckets, 2048 max)
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Fully Cone
ipt_AUTOFW loading
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
tunl0: Disabled Privacy Extensions
Mobile IPv6
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 132k freed
reset_btn : reset_btn reboot
ftok: No such file or directory
msgget: No such file or directory
shared_nvram = NULL shared_nvram 2ac8b00008x created 0
[sighandler]: No more events to be processed, quitting.
[cleanup]: Waiting for children.
[cleanup]: All children terminated.
insmod: reset_btn.ko: no module by that name found
psmon: not found
Starting Watchdog function !!!!!!!
cat: /proc/watchdog_ctrl_folder/watchdog_ctrl_run: No such file or directory
Done
IOCTL error in (init.c) => (start_console)shared_nvram = NULL shared_nvram 2aac600008x created 0
shared_nvram = NULL shared_nvram 2acd300008x created 0
shared_nvram = NULL shared_nvram 2acea00008x created 0
shared_nvram = NULL shared_nvram 2ad0100008x created 0
shared_nvram = NULL shared_nvram 2ad1800008x created 0
shared_nvram = NULL shared_nvram 2ad2f00008x created 0
shared_nvram = NULL shared_nvram 2ad4600008x created 0
shared_nvram = NULL shared_nvram 2ad5d00008x created 0
shared_nvram = NULL shared_nvram 2ad7400008x created 0
shared_nvram = NULL shared_nvram 2ad8b00008x created 0
shared_nvram = NULL shared_nvram 2ada200008x created 0
shared_nvram = NULL shared_nvram 2adb900008x created 0
shared_nvram = NULL shared_nvram 2ade700008x created 0
shared_nvram = NULL shared_nvram 2adfe00008x created 0
shared_nvram = NULL shared_nvram 2ae1500008x created 0
insmod: lm.ko: no module by that name found
insmod: dwc_otg.ko: no module by that name found
# lan services init......
/proc/sys/net/ipv4/ip_conntrack_max: cannot create
iptables: No chain/target/match by that name
waitpid: No child processes
vconfig config_loopback, route: No child processes
waitpid: No child processes
route: SIOC[ADD|DEL]RT: File exists
waitpid: No child processes
===== RT3052 switch init =====
vconfig: socket or ioctl error for add: Invalid argument
waitpid: No child processes
vconfig add eth2 1: No child processes
vconfig: socket or ioctl error for add: Invalid argument
waitpid: No child processes
vconfig add eth2 2: No child processes
switch reg write offset=40, value=1001
waitpid: No child processes
switch reg w 40 1001: No child processes
switch reg write offset=44, value=1001
waitpid: No child processes
switch reg w 44 1001: No child processes
switch reg write offset=48, value=1002
waitpid: No child processes
switch reg w 48 1002: No child processes
switch reg write offset=70, value=ffff506f
waitpid: No child processes
switch reg w 70 ffff506f: No child processes
===== start_wireless =====
Creat rmain device for LED and insmod it.
Setting ra0 configuration....
CountryRegionABand=1
WirelessMode=9
TxRate=0
Channel=0
BeaconPeriod=100
DtimPeriod=1
TxPower=100
BGProtection=0
RTSThreshold=2347
FragThreshold=2346
TxBurst=1
ShortSlot=1
PktAggregate=0
NoForwarding=0
NoForwardingBTNBSSID=0
HideSSID=0
Key1Type=0
Key2Type=0
Key3Type=0
Key4Type=0
WdsEnable=0
WdsList=
WdsKey=
WdsEncrypType=NONE
AutoChannelSelect=1
RekeyInterval=2000
AccessPolicy0=0
AccessPolicy1=0
RADIUS_Server=0.0.0.0
RADIUS_Port=1812
RADIUS_Key=
Ethifname=vlan1
own_ip_addr=192.168.123.1
session_timeout_interval=0
DisableOLBC=0
TxPreamble=0
WmmCapable=1
AckPolicy=0;0;0;0
APAifsn=3;7;1;1
APCwmin=4;4;3;2
APCwmax=6;10;4;3
APTxop=0;0;94;47
APACM=0;0;0;0
BSSAifsn=3;7;2;2
BSSCwmin=4;4;3;2
BSSCwmax=10;10;4;3
BSSTxop=0;0;94;47
BSSACM=0;0;0;0
TxAntenna=1
BasicRate=15
IEEE8021X=0
Set N mode parameter...
Bring up ra0 interface....
No need to change ra0 to Nintendo NDS capable
No need to change ra0 to Nintendo NDS capable...Complete
ra0       mac:
[0x00001300]:00063330
ra0       mac:
[0x00001304]:000a3700
killall: rt2860apd: no process killed
killall : No such file or directory
waitpid: No child processes
get_WPS_PIN_code : WSCStatus : 42874324
killall: wscd: no process killed
route: SIOC[ADD|DEL]RT: Network is down
waitpid: No child processes
ra0       mac:
[0x0000102c]:0f031e46
The FW is NOT for WIN 7 LOGO TEST
SIOCSIFHWADDR: No such device
SIOCSIFADDR: No such device
SIOCGIFFLAGS: No such device
interface vlan0 does not exist!
SIOCSIFHWADDR: No such device
SIOCSIFADDR: No such device
SIOCGIFFLAGS: No such device
interface eth1 does not exist!
interface eth2 does not exist!
SIOCSIFHWADDR: No such device
SIOCSIFADDR: No such device
SIOCGIFFLAGS: No such device
interface eth3 does not exist!
incorrect number of arguments for command
commands:
        addbr           <bridge>                add bridge
        delbr           <bridge>                delete bridge
        addif           <bridge> <device>       add interface to bridge
        delif           <bridge> <device>       delete interface from bridge
        setageing       <bridge> <time>         set ageing time
        setbridgeprio   <bridge> <prio>         set bridge priority
        setfd           <bridge> <time>         set bridge forward delay
        sethello        <bridge> <time>         set hello time
        setmaxage       <bridge> <time>         set max message age
        setpathcost     <bridge> <port> <cost>  set path cost
        setportprio     <bridge> <port> <prio>  set port priority
        show                                    show a list of bridges
        showmacs        <bridge>                show a list of mac addrs
        showstp         <bridge>                show bridge stp info
        stp             <bridge> <state>        turn stp on/off
set stp status failed: No such device
set hello timer failed: No such device
set ageing time failed: No such device
SIOCSIFADDR: No such device
SIOCSIFNETMASK: No such device
SIOCSIFBRDADDR: No such device
gPassiveMsgQ Init success! gPassiveMsgID=0x6!
gActiveMsgQ Init success!
sock=5!(0x0x7f944cf8)
Create netlink socket thread success!
Create ioctl socket(6) success!
Pthread(wscDevNLHandle)Now waiting for the netlink socket incoming message!
(wscDevNLHandle):netlink socket data is available now.
waitpid: No child processes
ifconfig vlan2 up: No child processes
waitpid: No child processes
brctl addif br0 vlan1: No child processes
SIOCSIFHWADDR: Device or resource busy
lld2d: not found
wscNLEventRTMNewlinkHandle(wscDevNLHandle):netlink socket data is available now.
wscNLEventRTMNewlinkHandle(wscDevNLHandle):netlink socket data is available now.
wscNLEventRTMNewlinkHandle(wscDevNLHandle):netlink socket data is available now.
wscNLEventRTMNewlinkHandle(wscDevNLHandle):netlink socket data is available now.
wscNLEventRTMNewlinkHandle(wscDevNLHandle):netlink socket data is available now.
wscNLEventRTMNewlinkHandlewscd: SSDP UDP PORT = 1900
Error with UpnpInit -- -208
usage: /sbin/pppoecd interface -d -k [-i idle] [-u username] [-m modename] [-p passwd] [-a acname] [-s srvname] [-r mru] [-t mtu]
et0macaddr 00:00:94:DA:02:48
device vlan1 is already a member of a bridge; can't enslave it to bridge br0.
waitpid: No child processes
brctl addbr br0: No child processes
ARPING to 192.168.123.1 from 192.168.123.1 via br0
Sent 1 probes (1 broadcast(s))
Received 0 reply
waitpid: No child processes
wan_config ether fail: No child processes
waitpid: No child processes
wan_config 0.0.0.0: No child processes
waitpid: No child processes
wan_config mtu up: No child processes
Setting ra0 configuration....
CountryRegionABand=1
WirelessMode=9
TxRate=0
Channel=0
BeaconPeriod=100
DtimPeriod=1
TxPower=100
BGProtection=0
RTSThreshold=2347
FragThreshold=2346
TxBurst=1
ShortSlot=1
PktAggregate=0
NoForwarding=0
NoForwardingBTNBSSID=0
HideSSID=0
Key1Type=0
Key2Type=0
Key3Type=0
Key4Type=0
WdsEnable=0
WdsList=
WdsKey=
WdsEncrypType=NONE
AutoChannelSelect=1
RekeyInterval=2000
AccessPolicy0=0
AccessPolicy1=0
RADIUS_Server=0.0.0.0
RADIUS_Port=1812
RADIUS_Key=
Ethifname=vlan1
own_ip_addr=192.168.123.1
session_timeout_interval=0
DisableOLBC=0
TxPreamble=0
WmmCapable=1
AckPolicy=0;0;0;0
APAifsn=3;7;1;1
APCwmin=4;4;3;2
APCwmax=6;10;4;3
APTxop=0;0;94;47
APACM=0;0;0;0
BSSAifsn=3;7;2;2
BSSCwmin=4;4;3;2
BSSCwmax=10;10;4;3
BSSTxop=0;0;94;47
BSSACM=0;0;0;0
TxAntenna=1
BasicRate=15
IEEE8021X=0
Set N mode parameter...
Bring up ra0 interface....
insmod: cannot insert `/lib/modules/2.6.21/kernel/drivers/net/wireless/rt2860v2_ap/rt2860v2_ap.ko': Invalid parameters (17): Invalid argument
device ra0 is already a member of a bridge; can't enslave it to bridge br0.
No need to change ra0 to Nintendo NDS capable
No need to change ra0 to Nintendo NDS capable...Complete
ra0       mac:
[0x00001300]:00063330
ra0       mac:
[0x00001304]:000a3700
killall: rt2860apd: no process killed
killall : No such file or directory
waitpid: No child processes
get_WPS_PIN_code : WSCStatus : 42874324
killall: wscd: no process killed
waitpid: No child processes
gPassiveMsgQ Init success! gPassiveMsgID=0x9!
gActiveMsgQ Init success!
sock=5!(0x0x7fd57cf8)
Create netlink socket thread success!
Create ioctl socket(6) success!
Pthread(wscDevNLHandle)Now waiting for the netlink socket incoming message!
ra0       mac:
[0x0000102c]:0f031e46
The FW is NOT for WIN 7 LOGO TEST
Start dhcpd
wscd: SSDP UDP PORT = 1900
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
647ba8c0, 017ba8c0, 00ffffff
UPnP Initialized
         IP-Addr: 192.168.123.1 Port: 49152
         HW-Addr: 00:00:94:da:02:48!
Specifying the webserver root directory -- /etc_ro/xml/
UUID Str=uuid:28802880-2880-1880-a880-000094da0248!
alloc memory size=1135!
<?xml version="1.0" encoding="utf-8"?>
<root xmlns="urn:schemas-upnp-org:device-1-0">
  <specVersion>
    <major>1</major>
    <minor>0</minor>
  </specVersion>
  <device>
    <deviceType>urn:schemas-wifialliance-org:device:WFADevice:1</deviceType>
    <friendlyName>Belkin Wireless Router</friendlyName>
    <manufacturer>Belkin Corporation</manufacturer>
    <manufacturerURL>http://www.belkin.com</manufacturerURL>
    <modelDescription>Belkin Wireless Router</modelDescription>
    <modelName>Belkin Wireless Router</modelName>
    <modelNumber>F5D</modelNumber>
    <modelURL>http://www.belkin.com</modelURL>
    <serialNumber>111111111111</serialNumber>
<UDN>uuid:28802880-2880-1880-a880-000094da0248</UDN>
    <serviceList>
      <service>
        <serviceType>urn:schemas-wifialliance-org:service:WFAWLANConfig:1</serviceType>
        <serviceId>urn:wifialliance-org:serviceId:WFAWLANConfig1</serviceId>
        <SCPDURL>WFAWLANConfigSCPD.xml</SCPDURL>
        <controlURL>control</controlURL>
        <eventSubURL>event</eventSubURL>
      </service>
    </serviceList>
  </device>
waitpid: No child processes
Start httpd lan
</root>

Registering the RootDevice
         with descDocUrl: http://192.168.123.1:49152/description.xml
RootDevice Registered
WscLocalDevice:
        Device:
                FriendlyName=Belkin Wireless Router!
                DescDocURL=http://192.168.123.1:49152/description.xml!
                UDN=uuid:28802880-2880-1880-a880-000094da0248!
                PresURL=!
        Service:
                servIdStr=urn:wifialliance-org:serviceId:WFAWLANConfig1!
                servTypeStr=urn:schemas-wifialliance-org:service:WFAWLANConfig:1!
                scpdURL=http://192.168.123.1:49152/WFAWLANConfigSCPD.xml!
                eventURL=http://192.168.123.1:49152/event!
                controlURL=http://192.168.123.1:49152/control!
WscLocalDeviceInit Initialized
iptables: Bad rule (does a matching rule exist in that chain?)
waitpid: No child processes
=====Start internet_detecter =====
 dnsmasq: started, version 2.38 cache disabled
dnsmasq: compile time options: IPv6 GNU-getopt no-ISC-leasefile no-DBus no-I18N TFTP
dnsmasq: ignoring nameserver 192.168.123.1 - local interface
killall: rt2860apd: no process killed
waitpid: No child processes
/tmp/del_route: cannot open
waitpid: No child processes
iptables: No chain/target/match by that name
waitpid: No child processes
iptables: No chain/target/match by that name
waitpid: No child processes
lld2d: No such file or directory
killall : No such file or directory
waitpid: No child processes
get_WPS_PIN_code : WSCStatus : 42874324
(wscDevNLHandle):netlink socket data is available now.
wscNLEventRTMNewlinkHandleRecevive a RAWSCMSG segment
pSegHdr->ackID=0x0!
Receive a new wireless event(WscActiveMsg):
        WscActiveMsgHdr->msgLen=51
        WscActiveMsgHdr->envID=0xfffeebd2
        WscActiveMsgHdr->ackID=0x0
        WscActiveMsgHdr->flags=0x0
        WscActiveMsgHdr->segLen=51
wscActiveMsgHandler(): the ActiveMsgType=18, SubType=2!
find ActiveMsgHandler!
WscEventMgmtMsgRecv:Receive a MGMT event, msgSubType=2
(WscEventMgmt_ConfigReq):Ready to parse the K2U msg(len=51)!

---StartOfMsgHexDump:WscEventMgmt_ConfigReq-K2UMsg
12 00 02 00 00 00 00 00 27 00 00 00 53 6d 61 72
74 48 75 62 2d 41 57 52 54 35 35 30 4e 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 94 da
02 48 03
---EndOfMsgHexDump!
(WscEventMgmt_ConfigReq): Status =3!
<-----End(WscEventMgmt_ConfigReq)
waitpid: No child processes
route: SIOC[ADD|DEL]RT: File exists
waitpid: No child processes
gPassiveMsgQ Init success! gPassiveMsgID=0xa!
gActiveMsgQ Init success!


BusyBox v1.1.0 (2010.07.16-02:49+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.

# sock=5!(0x0x7fc2ecf8)
Pthread(wscDevNLHandle)Now waiting for the netlink socket incoming message!
Create netlink socket thread success!
Create ioctl socket(6) success!
wscd: SSDP UDP PORT = 1900
UPnP Initialized
         IP-Addr: 192.168.123.1 Port: 49152
         HW-Addr: 00:00:94:da:02:48!
Specifying the webserver root directory -- /etc_ro/xml/
UUID Str=uuid:28802880-2880-1880-a880-000094da0248!
alloc memory size=1135!
<?xml version="1.0" encoding="utf-8"?>
<root xmlns="urn:schemas-upnp-org:device-1-0">
  <specVersion>
    <major>1</major>
    <minor>0</minor>
  </specVersion>
  <device>
    <deviceType>urn:schemas-wifialliance-org:device:WFADevice:1</deviceType>
    <friendlyName>Belkin Wireless Router</friendlyName>
    <manufacturer>Belkin Corporation</manufacturer>
    <manufacturerURL>http://www.belkin.com</manufacturerURL>
    <modelDescription>Belkin Wireless Router</modelDescription>
    <modelName>Belkin Wireless Router</modelName>
    <modelNumber>F5D</modelNumber>
    <modelURL>http://www.belkin.com</modelURL>
    <serialNumber>111111111111</serialNumber>
<UDN>uuid:28802880-2880-1880-a880-000094da0248</UDN>
    <serviceList>
      <service>
        <serviceType>urn:schemas-wifialliance-org:service:WFAWLANConfig:1</serviceType>
        <serviceId>urn:wifialliance-org:serviceId:WFAWLANConfig1</serviceId>
        <SCPDURL>WFAWLANConfigSCPD.xml</SCPDURL>
        <controlURL>control</controlURL>
        <eventSubURL>event</eventSubURL>
      </service>
    </serviceList>
  </device>
</root>

Registering the RootDevice
         with descDocUrl: http://192.168.123.1:49152/description.xml
RootDevice Registered
WscLocalDevice:
        Device:
                FriendlyName=Belkin Wireless Router!
                DescDocURL=http://192.168.123.1:49152/description.xml!
                UDN=uuid:28802880-2880-1880-a880-000094da0248!
                PresURL=!
        Service:
                servIdStr=urn:wifialliance-org:serviceId:WFAWLANConfig1!
                servTypeStr=urn:schemas-wifialliance-org:service:WFAWLANConfig:1!
                scpdURL=http://192.168.123.1:49152/WFAWLANConfigSCPD.xml!
                eventURL=http://192.168.123.1:49152/event!
                controlURL=http://192.168.123.1:49152/control!
WscLocalDeviceInit Initialized
Advertisement Sent
check_WPS_status : WSCStatus is 3 now...STATUS_WSC_LINK_UP
WPS BUTTON press!!

cat /proc/version

# cat /proc/version
Linux version 2.6.21 (terry_kuo@cvs4) (gcc version 3.4.2) #183 Fri Jul 16 10:49:36 CST 2010

cat /proc/mtd

# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00050000 00010000 "uboot"
mtd1: 00790000 00010000 "Kernel and Rootfs"
mtd2: 00630000 00010000 "Rootfs"
mtd3: 00010000 00010000 "Nvram"
mtd4: 00010000 00010000 "Factory"

cat /proc/cpuinfo

# cat /proc/cpuinfo
system type             : Ralink SoC
processor               : 0
cpu model               : MIPS 24K V4.12
BogoMIPS                : 255.48
wait instruction        : yes
microsecond timers      : yes
tlb_entries             : 32
extra interrupt vector  : yes
hardware watchpoint     : yes
ASEs implemented        : mips16 dsp
VCED exceptions         : not available
VCEI exceptions         : not available

ps w

# ps w
  PID  Uid     VmSize Stat Command
    1 0           604 S   /sbin/init
    2 0               SWN [ksoftirqd/0]
    3 0               SW< [events/0]
    4 0               SW< [khelper]
    5 0               SW< [kthread]
   28 0               SW< [kblockd/0]
   29 0               SW< [cqueue/0]
   32 0               SW< [khubd]
   44 0               SW< [kswapd0]
   45 0               SW  [pdflush]
   46 0               SW  [pdflush]
   47 0               SW< [aio/0]
  645 0               SW  [mtdblockd]
 1953 0           280 S   /bin/usb_storage_hotplug
 1955 0           364 S   /hotplug2/sbin/hotplug2 --persistent
 1961 0           304 S   resetC
 2675 0           356 S   /sbin/syslogd -n
 3274 0           352 S   easytest
 3306 0               SW  [rtmpWscHandle]
 3408 0               DW  [NU UDP]
 3409 0               SW  [NU TCP]
 3410 0               SW  [KCconfigUdpSer]
 3411 0               SW  [KCconfigTcpSer]
 3471 0           360 S   /bin/httpd
 3476 0           324 S   /bin/udhcpd /tmp/udhcpd.conf
 3478 0           416 S   dnsmasq -h -d -r /tmp/resolv.conf
 3479 0           324 S   internet_detect
 3494 0           272 S   mssid_redirect
 3513 0           388 S   mDNSResponderPosix -n AWRT-550N -t _http._tcp. -p 80
 3518 0           684 S   /usr/sbin/wscd -i ra0 -m 1 -d 3
 3519 0           684 S   /usr/sbin/wscd -i ra0 -m 1 -d 3
 3520 0           420 S   /bin/sh
 3521 0           684 S   /usr/sbin/wscd -i ra0 -m 1 -d 3
 3522 0           684 S   /usr/sbin/wscd -i ra0 -m 1 -d 3
 3523 0           684 S   /usr/sbin/wscd -i ra0 -m 1 -d 3
 3525 0           684 S   /usr/sbin/wscd -i ra0 -m 1 -d 3
 3526 0           684 S   /usr/sbin/wscd -i ra0 -m 1 -d 3
 3527 0           684 S   /usr/sbin/wscd -i ra0 -m 1 -d 3
 3529 0           684 S   /usr/sbin/wscd -i ra0 -m 1 -d 3
 3530 0           684 S   /usr/sbin/wscd -i ra0 -m 1 -d 3
 4000 0           352 R   ps w

lsmod

# lsmod
Module                  Size  Used by    Tainted: PF
NetUSB                195552  0
rt2860v2_ap           925584  1
raeth                  36224  1