BOLT BL100
From TechInfoDepot
Jump to navigationJump to search
| abgn+ac (AC1200) | |
|---|---|
| Modem Router Wireless | |
 | |
| 3rd Party Firmware | |
| dd-wrt | Status Unknown |
| OpenWrt | Supported |
| Tomato any flavor | Incompatible |
| Gargoyle | Status Unknown |
| Platform | |
| Brand • Model • Rev | BOLT BL100 |
| FCC ID | none specified |
| Type | wireless router, LTE modem |
CPU1  | MediaTek MT7620A |
| CPU1 Type | MIPS 24KEc |
| CPU1 Speed | 580 MHz 32-bit |
| Flash1 Chip | Winbond W25Q128BV |
| Flash1 Size | 16 MiB 16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> |
| RAM1 Size | 64 MiB 67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br /> |
| RAM1 Chip | Brand? Model? |
| ETH chip1 | MediaTek MT7620A |
| Switch | MediaTek MT7620A |
| Ethernet Port Count | 2-100MbE-LAN |
| Wired Standard | IEEE 802.3i/3u |
|
802dot11 OUI: none specified | |
| Stock bootloader | U-Boot |
| Expansion IF types | none specified |
| Power | 12 VDC, 1 A |
| Connector type | barrel |
| Serial Port (UART) | yes, 3.3V TTL, (57600 8N1) |
|
Flags: | |
|
| |
| Other | |
|
| |
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) |
| Radio 1 | |
| Chip1 | MediaTek MT7620A |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 2x2:2 |
| Wireless Standard | IEEE 802.11b/g/n |
| 802.11n | up to 300 Mbps |
| 802.11g | up to 54 Mbps |
| 802.11b | up to 11 Mbps |
| WiFi Operating Frequency | 2.4 GHz |
| Radio 2 | |
| Chip1 | MediaTek MT76x2E |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 2x2:2 |
| Wireless Standard | IEEE 802.11a/n/ac |
| 802.11ac | up to 867 Mbps |
| 802.11n | up to 300 Mbps |
| 802.11a | up to 54 Mbps |
| WiFi Operating Frequency | 5 GHz |
For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.
Flashing
 | NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
 | This device is NOT RECOMMENDED for future use with OpenWrt due to low flash/ram.
DO NOT BUY DEVICES WITH 8MB FLASH / 64MB RAM if you intend to flash an up-to-date and secure OpenWrt version onto it! See 8/64 warning for details. This device does not have sufficient resources (flash and/or RAM) to provide secure and reliable operation. This means that you will not be able to install many packages, and that you might experience crashes due to OOM situations more or less often. See OpenWrt on 8/64 devices what you can do now. |
Target: ramips
Subtarget: mt7620
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 24.10.0
Current supported version: 24.10.5
Subtarget: mt7620
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 24.10.0
Current supported version: 24.10.5
LAN Hardware: MediaTek MT7620A
LAN Comment: Qualcomm LTE B40
WLAN Hardware: MediaTek MT7620A, Mediatek MT76x2E
Installation method(s):
Telnet, U-Boot TFTP + serial recovery, see git-commit
Recovery method(s):
U-Boot TFTP + serial recovery, see git-commit
LAN Comment: Qualcomm LTE B40
WLAN Hardware: MediaTek MT7620A, Mediatek MT76x2E
Installation method(s):
Telnet, U-Boot TFTP + serial recovery, see git-commit
Recovery method(s):
U-Boot TFTP + serial recovery, see git-commit
| git • >> |
|---|
ramips: add support for BOLT BL100 BL100 is a router made by Bolt by a provider in Indonesia The original firmware created using Mediatek SDK and kernel 2.6.36 - Chipset: MediaTek MT7620A ver 2, eco 6 - RAM: 64 MB - Bootloader: U Boot - Flash: Winbond W25Q128BV (16 MB) - Ports: 2x 10/100 Ethernet, 1x RJ-11 VoIP - Modem: Qualcomm LTE B40 (2300 Mhz) VID:05c6 PID:9026 - Wireless: Internal MT7620A (2.4 Ghz) & Mediatek MT76x2E (5.8 Ghz) - Switch: MediaTek MT7620A built-in 5-port 10/100M switch - Voltage: DC 12V 1A - Antenna Port: 2x External Antenna, 2 LTE U.FL, 2 WiFi U.FL - Serial Port: Yes, 3.3 V TTL, Baud 57600 8N1 - Buttons: Reset and WPS - LED: 15 Total - 4 blue lte, 2 red lte, 1 reset, 1 power. - 1 wps, 1 voip, 1 wlan2, 1 wlan5, 1 lan, 1 wan, 1 wlan. Installation via stock firmware 1. Unlock Telnet access by downloading the backup .tar.gz file 2. Change the Telnet configuration to LAN_Telnet=1 3. Import backup configuration 4. Restart the router 5. Login to telnet with username and password = admin : db40 6. Download sysupgrade binary and mtd_write to the kernel partition `mtd_write write openwrt-bolt_bl100-squashfs-sysupgrade.bin Kernel` Signed-off-by: Radito Wahyu |
Categories:
- BOLT
- Embedded system/wireless router
- Embedded system/LTE modem
- Embedded System MediaTek
- Embedded System MT7620A
- MediaTek
- Embedded System MIPS 24KEc
- Embedded System
- OpenWrt Supported
- Has Mimo Status
- Embedded System IEEE 802.11b/g/n
- Embedded System MT76x2E
- Embedded System IEEE 802.11a/n/ac
- Dual-Radio Wireless Embedded System
- Wireless Embedded System
- Dual-Band
- English Documentation
