Cambium Networks XE3-4
From TechInfoDepot
Jump to navigationJump to search
| abgn+ac+ax (AX4200) | |
|---|---|
| XE3-4 Wi-Fi 6E Indoor Wireless Access Point | |
|
| |
| Homepage | Product page |
| 3rd Party Firmware | |
| dd-wrt | Status Unknown |
| OpenWrt | Supported |
| Tomato any flavor | Incompatible |
| Gargoyle | Status Unknown |
| Platform | |
| Brand • Model • Rev | Cambium Networks XE3-4 |
| FCC ID (fcc.io) | none specified |
| FCC ID (fcc.report) | none specified |
| Type | access point |
| CPU1 | Qualcomm IPQ6010 |
| CPU1 Type | ARM Cortex-A53 |
| CPU1 Speed | 800 MHz ( 4 cores ) |
| Flash1 Chip | Macronix MX30UF2G18AC |
| Flash1 Size | 512 MiB 536,870,912 B <br />4,194,304 Kib <br />524,288 KiB <br />4,096 Mib <br />0.5 GiB <br /> (NAND) |
| Flash2 Chip | Winbond W25Q128FW |
| Flash2 Size | 16 MiB16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> |
| RAM1 Size | 1 GiB 1,024 MiB <br />1,073,741,824 B <br />8,388,608 Kib <br />1,048,576 KiB <br />8,192 Mib <br /> |
| RAM1 Chip | Brand? Model? |
| ETH chip1 | Qualcomm IPQ6010 |
| ETH chip2 | Qualcomm Atheros QCA8081 |
| ETH chip3 | Qualcomm Atheros QCA8072 |
| Ethernet Port Count |
1-2.5GbE-WAN 1-1GbE-LAN |
| Wired Standard | IEEE 802.3i/3u/3ab/3bz |
|
802dot11 OUI: none specified | |
| Stock bootloader | U-Boot |
| Expansion IF types | USB 2.0 |
| USB ports | 1 |
| USB Hub Compatible | Untested |
| PoE | 802.3bt, 802.3af, standard |
| Power | ? VDC, ? A |
|
Flags: | |
|
| |
| Other | |
|
| |
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) |
| Radio 1 | |
| Chip1 | Qualcomm IPQ6018 |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 2x2:2 |
| Wireless Standard | IEEE 802.11b/g/n/ax |
| 802.11ax | up to 574 Mbps |
| 802.11n | up to 300 Mbps |
| 802.11g | up to 54 Mbps |
| 802.11b | up to 11 Mbps |
| WiFi Operating Frequency | 2.4 GHz |
| Radio 2 | |
| Chip1 | Qualcomm IPQ6018 |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 2x2:2 |
| Wireless Standard | IEEE 802.11a/n/ac/ax |
| 802.11ax | up to 1201 Mbps |
| 802.11ac | up to 867 Mbps |
| 802.11n | up to 300 Mbps |
| 802.11a | up to 54 Mbps |
| WiFi Operating Frequency | 5.2 GHz |
| Radio 3 | |
| Chip1 | Qualcomm QCN9074 |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 4x4:4 |
| Wireless Standard | IEEE 802.11a/n/ac/ax |
| 802.11ax | up to 2402 Mbps |
| 802.11ac | up to 1733 Mbps |
| 802.11n | up to 600 Mbps |
| 802.11a | up to 54 Mbps |
| WiFi Operating Frequency | 5.8 GHz |
For a list of all currently documented Qualcomm chipsets with specifications, see Qualcomm.
For a list of all currently documented Qualcomm Atheros (QCA) chipsets with specifications, see Qualcomm Atheros.
Flashing
| NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
Target: qualcommax
Subtarget: ipq60xx
Package architecture: aarch64_cortex-a53
Support started version: 25.12.0
Current supported version: 25.12.1
Subtarget: ipq60xx
Package architecture: aarch64_cortex-a53
Support started version: 25.12.0
Current supported version: 25.12.1
LAN Hardware: Qualcomm Atheros QCA8072
LAN Comment: Qualcomm Atheros QCA8081 2.5G Phy
WLAN Hardware: Qualcomm IPQ6018, Qualcomm QCN9074
WLAN Comment: 2.4GHz: 2x2:2 MIMO, 5GHz: 2x2:2 MIMO, 6GHz: 4x4:4 MIMO
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
LAN Comment: Qualcomm Atheros QCA8081 2.5G Phy
WLAN Hardware: Qualcomm IPQ6018, Qualcomm QCN9074
WLAN Comment: 2.4GHz: 2x2:2 MIMO, 5GHz: 2x2:2 MIMO, 6GHz: 4x4:4 MIMO
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
| git • >> |
|---|
qualcommax: ipq60xx: add support for Cambium Networks XE3-4
Cambium Networks XE3-4 is a tri-radio Wi-Fi 6/6E 4×4/2×2 AP.
Hardware:
Model: Cambium Networks XE3-4
CPU: IPQ6010/AP-CP01-C3, SoC Version: 1.0 @ 800 MHz
Memory: 1 GiB
Flash: 512 MiB Macronix MX30UF2G18AC + W25Q128FW
Ethernet: 1x 1 GbE (QCA8072)
1x 2.5 GbE (QCA8081)
Buttons: 1x Reset
Serial: TX, RX, GND
Baudrate: 115200
Radios: Qualcomm Atheros IPQ6018 802.11ax - 2x2 - 2GHz
Qualcomm Atheros IPQ6018 802.11ax - 2x2 - 5GHz
Qualcomm Atheros QCN9074 802.11ax - 4x4 - 5GHz or 6GHz
BLE 4.1
Power: 32.0W 802.3bt5 PoE++
25.5W 802.3at with USB, BT disabled
Size: 215mm x 215mm
Ports: 1x USB 2.0
Antenna: 6 GHz: 6.29 dBi, Omni 30 dBm
5 GHz: 6.12 dBi, Omni 31 dBm
2.4 GHz: 4.85 dBi, Omni 29 dBm
LEDs: Multi-color status LEDs
Mounting: Wall, ceiling or T-bar
Installation: Serial connection
1. Open the AP to get access to the board. Connect RX, TX and GND.
2. Power on the AP, and short the CS pin of the SPI flash with
one of the APs GND pins.
3. Transfer the initramfs image with TFTP
(Default server IP is 192.168.0.120)
# tftpboot factory.ubi
4. Flash the rootfs partition
# flash rootfs
5. Reboot the AP
# reset
|
Categories:
- Cambium Networks
- Embedded system/access point
- Embedded System Qualcomm
- Embedded System IPQ6010
- Qualcomm
- Embedded System ARM
- Embedded System Cortex-A53
- Embedded System QCA8081
- Embedded System Qualcomm Atheros
- Qualcomm Atheros
- Embedded System QCA8072
- OpenWrt Supported
- Embedded System IPQ6018
- Has Mimo Status
- Embedded System IEEE 802.11b/g/n/ax
- Embedded System IEEE 802.11a/n/ac/ax
- Embedded System QCN9074
- Triple-Radio Wireless Embedded System
- Wireless Embedded System
- Tri-Band
- Embedded System
- English Documentation