CANYON CNP-WF514N3A/Serial info

bootlog • >>

CNP-WF514N3A mips #1 Fri Sep 3 12:18:20 CST 2010 (none) CNP-WF514N3A login: U-Boot 1.1.4 (Sep 3 2010 - 12:22:02) AP83 (ar9100) U-boot 0.0.11 DRAM: sri 32 MB id read 0x100000ff flash size 8MB, sector count = 128 Flash: 8 MB Using default environment In: serial Out: serial Err: serial Net: ag7100_enet_initialize... No valid address in Flash. Using fixed address : cfg1 0xf cfg2 0x7114 eth0: 00:03:7f:09:0b:ad eth0 up eth0 Autobooting in 1 seconds## Booting image at bf020000 ... Uncompressing Kernel Image ... OK Starting kernel ... Linux version 2.6.15--LSDK-6.1.1.40 gcc version 3.4.4 #1 Fri Sep 3 12:18:20 CST 2010 flash_size passed from bootloader = 8 CPU revision is: 00019374 Determined physical RAM map: memory: 02000000 @ 00000000 (usable) Built 1 zonelists Kernel command line: console=ttyS0,115200 root=31:2 rootfstype=squashfs init=/sbin/init Primary instruction cache 64kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). Cache parity protection disabled PID hash table entries: 256 (order: 8, 4096 bytes) Using 200.000 MHz high precision timer. Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 30148k/32768k available (1406k kernel code, 2604k reserved, 293k data, 112k init, 0k highmem) Mount-cache hash table entries: 512 Checking for 'wait' instruction... available. NET: Registered protocol family 16 Jumpstart button pressed. SCSI subsystem initialized AR7100 GPIOC major 0 squashfs: version 3.3 (2007/10/31) Phillip Lougher squashfs: LZMA suppport for slax.org by jro Initializing Cryptographic API io scheduler noop registered io scheduler deadline registered Serial: 8250/16550 driver $Revision: #1 $ 1 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x0 (irq = 19) is a 16550A RAMDISK driver initialized: 1 RAM disks of 8192K size 1024 blocksize PPP generic driver version 2.4.2 PPPoX init, max protocols:3 NET: Registered protocol family 24 pppox protocol 0 register. max:3 cmdlinepart partition parsing not available Searching for RedBoot partition table 5 RedBoot partitions found on MTD device ar7100-nor0 Creating 5 MTD partitions on "ar7100-nor0": 0x00000000-0x00020000 : "boot" 0x00020000-0x00120000 : "kernel" 0x00120000-0x007e0000 : "rootfs" 0x007e0000-0x007f0000 : "config" 0x007f0000-0x00800000 : "art" ->Oops: flash id 0x10216 . NET: Registered protocol family 2 IP route cache hash table entries: 512 (order: -1, 2048 bytes) TCP established hash table entries: 2048 (order: 1, 8192 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> ar7100wdt_init: Registering WDT success VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 112k freed init started: BusyBox v1.01 (2010.09.17-01:36+0000) multi-call binary Algorithmics/MIPS FPU Emulator v1.5 This board use 2.6.15 ip_conntrack version 2.4 (256 buckets, 5120 max) - 244 bytes per conntrack statistics: module license 'BSD' taints kernel. insmod: cannot open module `/lib/modules/2.6.15/kernel/flashid.ko': No such file or directory pppox protocol 1 register. max:3 PPPoL2TP kernel driver, V0.17. fixed many bug. drop rcv pkts and xmit pkts while no buffer, use pass time HZ/4.only drop ip pkt. no printk. xl2tpd 15 retries xmit. 08.20 PPTP driver version 0.8.3 pppox protocol 2 register. max:3 insmod: cannot open module `/lib/modules/2.6.15/kernel/harmony.ko': No such file or directory Now flash open! Now flash open! AG7100: Length per segment 1536 AG7100: Max segments per packet 1 AG7100: Max tx descriptor count 40 AG7100: Max rx descriptor count 252 AG7100: fifo cfg 3 00780008 (none) mips #1 Fri Sep 3 12:18:20 CST 2010 (none) (none) login: rtl8368s_getAsicPHYRegs(0, 1, 22, &data) return is 0, data is 0x00001000 ++ PVID: 0x00000001, bitmap: 0x00000021 ++ PVID: 0x00000003, bitmap: 0x0000003e ++ PVID: 0x00000005, bitmap: 0x0000003e ++ PVID: 0x00000007, bitmap: 0x0000003e ++ PVID: 0x00000009, bitmap: 0x0000003e vtable vid: 0x00000002, bitmap 0x00000022 vtable vid: 0x00000004, bitmap 0x00000024 vtable vid: 0x00000006, bitmap 0x00000026 vtable vid: 0x00000008, bitmap 0x00000028 vtable vid: 0x0000000a, bitmap 0x0000002a vtable vid: 0x0000000c, bitmap 0x0000002c vtable vid: 0x0000000e, bitmap 0x0000002e vtable vid: 0x00000010, bitmap 0x00000030 vtable vid: 0x00000012, bitmap 0x00000032 vtable vid: 0x00000014, bitmap 0x00000034 vtable vid: 0x00000016, bitmap 0x00000036 vtable vid: 0x00000018, bitmap 0x00000038 vtable vid: 0x0000001a, bitmap 0x0000003a vtable vid: 0x0000001c, bitmap 0x0000003c vtable vid: 0x0000001e, bitmap 0x0000003e AG7100: pll reg 0x18050014: 0x1a000000 Writing 4 SIOCETHTOOL bridge: can't decode speed from eth0: 0 device eth0 entered promiscuous mode Now flash open! AG7100: pll reg 0x18050014: 0x1a000000 Writing 4 br0: port 1(eth0) entering learning state br0: topology change detected, propagating br0: port 1(eth0) entering forwarding state ip_conntrack_rtsp v0.01 loading ip_nat_rtsp v0.01 loading ath_hal: 0.9.17.1 (AR5416, DEBUG, REGOPS_FUNC, WRITE_EEPROM, 11D) wlan: 0.8.4.2 (Atheros/multi-bss) ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved ath_ahb: 0.9.4.5 (Atheros/multi-bss) Howl Revision ID 0xb9 <6>wifi0: Atheros AR9100 WiSoC: mem=0xb80c0000, irq=2 wlan_me: Version 0.1 Copyright (c) 2008 Atheros Communications, Inc. All Rights Reserved wlan: mac acl policy registered TP_Flags:6**** The selected channel is 1 Country ie is DE Country ie is DE maxrate = 300000 Country ie is DE br0: port 1(eth0) entering disabled state AG7100: pll reg 0x18050014: 0x1a000000 Writing 4 br0: port 1(eth0) entering learning state br0: topology change detected, propagating br0: port 1(eth0) entering forwarding state device ath0 entered promiscuous mode br0: port 2(ath0) entering learning state br0: topology change detected, propagating br0: port 2(ath0) entering forwarding state br0: port 2(ath0) entering disabled state Country ie is DE br0: port 2(ath0) entering learning state br0: topology change detected, propagating br0: port 2(ath0) entering forwarding state br0: port 2(ath0) entering disabled state TP_Flags:6**** TP_Flags:0**** Country ie is DE br0: port 2(ath0) entering learning state br0: topology change detected, propagating br0: port 2(ath0) entering forwarding state fuse init (API version 7.8) fuse distribution version: 2.7.4 usbcore: registered new driver usbfs usbcore: registered new driver hub Port Status c000004 ar7100-ehci ar7100-ehci.0: ATH EHCI ar7100-ehci ar7100-ehci.0: new USB bus registered, assigned bus number 1 ar7100-ehci ar7100-ehci.0: irq 3, io mem 0x1b000000 hcc_params addr 0xbb000108 val 0x6 hcs_params addr 0xbb000104 val 0x10011 ar7100-ehci ar7100-ehci.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. SIOCENABLEFWD Inteference detected rx_clear=100, rx_frame=0, tx_frame=0 ath_bstuck_tasklet... Calling ath_internal reset erase 0xbf020000 +7c0000 Password: Login incorrect CNP-WF514N3A login: CNP-WF514N3A login: admin login: no valid shadow password CNP-WF514N3A mips #1 Fri Sep 3 12:18:20 CST 2010 (none) CNP-WF514N3A login: