Ctera C200-2

From TechInfoDepot
Jump to navigationJump to search
multiple revisions of this device, use caution
Cloud Attached Storage Appliance
Homepage Product page
WikiDevi.wi-cat.ru Ctera C200-2
3rd Party Firmware
dd-wrt Status Unknown
OpenWrt Supported
Tomato any flavor Incompatible
Gargoyle Status Unknown
Platform
Brand • Model • Rev Ctera CT-C200 v2
Board ID AQR00C-1.6MM
Type NAS
CPU1 checkY Marvell 88F6707
CPU1 Type ARMv7 (PJ4 core)
CPU1 Speed 1.0 GHz
Flash1 Chip ESMT F59L2G81A-25T
Flash1 Size 256 MiB 268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br /> (NAND)
RAM1 Size 1 GiB 1,024 MiB <br />1,073,741,824 B <br />8,388,608 Kib <br />1,048,576 KiB <br />8,192 Mib <br /> (DDR3L SDRAM)
RAM1 Chip Nanya NT5CC512M8DN-DI x 2
ETH chip1 Marvell 88F6707
ETH chip2 Marvell 88E1318
Ethernet Port Count 1-1GbE-LAN
Wired Standard IEEE 802.3/3u/3ab

Ethernet OUI: 00:25:25 (2 E, -)

Stock bootloader U-Boot 2011.12 Marvell version: v2011.12 2013_Q1.0p2
Stock FW OS Linux
Expansion IF types SATA II, USB 3.0
USB ports 2
SATA Ports 2
USB Hub Compatible Untested
Power 12 VDC, 5 A
Connector type barrel
5.5 mm (OD)
2.5 mm (ID)
9.5 mm (LEN)
Serial Port (UART) yes, 4-pin header, populated, J3, 3.3V TTL, (115200 8N1)
JTAG Port yes, 20-pin header, unpopulated, J2

Flags:
RTC w/ battery, buzzer, fan

Additional chips
Precision Timer;TI;NE555;;1;
2-Wire RTC IC;Seiko;S35390A;;1;
Hardware Monitoring IC;Novoton;NCT7802Y;;1;
USB 3.0 Host Controller;Renasas;uPD720202;;1;
Field Programmable DSP Switcher;Marvell;88PG847B;;1;
1A Low Dropout Voltage Regulator;GlobalTech;GS1117AX;;1;
3A Synchronous Step-Down Switcher w/ Integrated FET;TI;TPS54327;;3;

Other

Default IP address: acquired via DHCP
the IP acquired via DHCP is used by 268 additional devices
of which 1 are Ctera devices

Manuf/OEM/ODM SerComm
3rd Party Firmware Support OpenWrt • (List | Dev | DLs)
Retail
Availability End of Life
ASIN B00OJMPNY8 , 
multiple uses
Country of manuf Taiwan
 CPU1 brandFLA1RAM1
Ctera C200Marvell256 MiB268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br />512 MiB536,870,912 B <br />4,194,304 Kib <br />524,288 KiB <br />4,096 Mib <br />0.5 GiB <br />
Ctera C200-2Marvell256 MiB268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br />1,024 MiB1,073,741,824 B <br />8,388,608 Kib <br />1,048,576 KiB <br />8,192 Mib <br />1 GiB <br />

For a list of all currently documented Marvell chipsets with specifications, see Marvell.

For a list of all currently documented Ctera devices with specifications, see Ctera.

Overview

"AQR00C-1.6MM" is silk-screened on the main board.

Hardware specification

ARMADA 370 (PJ4 Core) ARM v7
  • Storage: 256MB (NAND) Flash, 2x SATA II
  • Memory: 1GB (DDR3L) SDRAM
  • Network: 1x Gigabit Ethernet ports
  • USB: 2x USB 3.0 ports (Renesas uPD720202)
  • Power: 12V/5A via barrel

Links of Interest

CTERA Networks on Wikipedia

Flashing

Flashing OpenWrt

Target: mvebu
Subtarget: cortexa9
Package architecture: arm_cortex-a9_vfpv3-d16
Supported Since Commit
Support started version: 22.03.0
Current supported version: 24.10.5
LAN Comment: PHY: Marvell 88E1318
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
git • >> 
mvebu: cortexa9: Add support for Ctera C200-V2
2-Bay NAS - maximum two 3.5" Harddisks

Hardware:
  - SoC: Marvell 88F6707-A1 ARMv7 Processor 1,2GHz (ARMADA 370 SoC)
  - Ram: 1GB (2x Nanya NT5CC512M8DN-D1)
  - NAND Flash: 256MB (ESMT F59L2G81A-25T)
  - Lan: 1x GBE (Marvell 88E1318-NNB2)
  - Storage: 2x SATA HDD 3.5" Slot
  - USB: 2x USB 3.0 port (Renesas uPD720202)
  - Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND)
  - LEDs: 13x GPIO controlled
  - Buttons: 2x GPIO controlled

Known issues:
  - Buzzer is unused due lack of proper driver
  - USB1/2 usbport ledtrigger won't work (through DT)
  - Renesas uPD720202 requires firmware file. It's possible to find
    non-free binary. Please look for 'UPDATE.mem' file and put in into
    '/lib/firmware/renesas_usb_fw.mem' file.

Installation:
  - Apply factory initramfs image via stock web-gui.
  - Do sysupgrade to make installation complete.

Back to stock:
  - OpenWrt rootfs partition use unused space after stock firmware.
  - Full revert is possible.
  - Login via ssh and run:

 ## ctera_c200-v2_back_to_factory start ##
 . /lib/functions.sh
 part=$(find_mtd_part "active_bank")
 active_bank=$(strings "$part" | grep bank)
 if [ "$active_bank" = "bank1" ]; then
 	echo "bank2" > /tmp/change_bank
 else
 	echo "bank1" > /tmp/change_bank
 fi
 mtd write /tmp/change_bank active_bank
 reboot
 ## ctera_c200-v2_back_to_factory end ##

Pictures

User Images
  • Board top
    Board top
  • Board bottom
    Board bottom

See also

Wikipedia:CTERA_Networks
Retrieved from "https://techinfodepot.shoutwiki.com/w/index.php?title=Ctera_C200-2&oldid=520093"