Cudy AP1300 Outdoor
From TechInfoDepot
Jump to navigationJump to search
| abgn+ac (AC1200) | |
|---|---|
| AC1300 Outdoor Wi-Fi 5 Access Point | |
|
| |
| Homepage | Product page |
| WikiDevi.wi-cat.ru | Cudy AP1300 Outdoor |
| 3rd Party Firmware | |
| dd-wrt | Status Unknown |
| OpenWrt | Supported |
| Tomato any flavor | Incompatible |
| Gargoyle | Status Unknown |
| Platform | |
| Brand • Model • Rev | Cudy AP1300 |
| FCC ID | none specified |
| Type | access point |
| CPU1 | MediaTek MT7621DAT |
| CPU1 Type | MIPS 1004Kc |
| CPU1 Speed | 880 MHz ( 2 cores ) 16-bit |
| Flash1 Chip | XMC XM25QH128C |
| Flash1 Size | 16 MiB 16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> |
| RAM1 Size | 128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> |
| RAM1 Chip | MediaTek MT7621DAT |
| ETH chip1 | MediaTek MT7621DAT |
| Ethernet Port Count | 1-1GbE-LAN |
| Wired Standard | IEEE 802.3i/3u/3ab |
| Expansion IF types | none specified |
| PoE | 802.3at, 802.3af, standard |
| Power | ? VDC, ? A |
| Connector type | Ethernet (PoE) |
| Serial Port (UART) | yes, 4-pin header, 3.3V TTL, (115200 8N1), J4 |
|
| |
|
| |
| Other | |
|
| |
| Manuf/OEM/ODM | Cudy |
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) |
| Retail | |
| Country of manuf | China |
| Radio 1 | |
| Chip1 | MediaTek MT7603EN |
| Wireless interface OUI | 80:AF:CA |
| Antenna Connector Type | soldered |
| MIMO status | 2x2:2 |
| Wireless Standard | IEEE 802.11b/g/n |
| 802.11n | up to 300 Mbps |
| 802.11g | up to 54 Mbps |
| 802.11b | up to 11 Mbps |
| WiFi Operating Frequency | 2.4 GHz |
| Radio 2 | |
| Chip1 | MediaTek MT7613BE |
| Wireless interface OUI | 80:AF:CA |
| Antenna Connector Type | soldered |
| MIMO status | 2x2:2 |
| Wireless Standard | IEEE 802.11a/b/g/n/ac |
| 802.11ac | up to 867 Mbps |
| 802.11n | up to 300 Mbps |
| 802.11a | up to 54 Mbps |
| WiFi Operating Frequency | 5 GHz |
For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.
For a list of all currently documented Cudy devices with specifications, see Cudy.
Links of Interest
Models
|
|
Flashing
| NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
Target: ramips
Subtarget: mt7621
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 24.10.5
Current supported version: 25.12.5
Subtarget: mt7621
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 24.10.5
Current supported version: 25.12.5
WLAN Hardware: MediaTek MT7603E, MediaTek MT7613BEN
Installation method(s):
GUI OEM, U-Boot TFTP recovery, see git-commit
Install Comment:
Need a signed OpenWrt intermediary image from Cudy before installing official OpenWrt image
Recovery method(s):
U-Boot TFTP recovery
Comment:
reported support by DeviWiki, no info on OpenWrt
Installation method(s):
GUI OEM, U-Boot TFTP recovery, see git-commit
Install Comment:
Need a signed OpenWrt intermediary image from Cudy before installing official OpenWrt image
Recovery method(s):
U-Boot TFTP recovery
Comment:
reported support by DeviWiki, no info on OpenWrt
| git • >> |
|---|
ramips: mt7621: add support for Cudy AP1300 Outdoor v1 Hardware: - SoC: MediaTek MT7621DAT - Flash: 16 MiB XM25QH128C - RAM: 128 MiB - WLAN: 2.4 GHz (MT7603E, 11n), 5 GHz (MediaTek MT7613BEN, 11ac) - Ethernet: 1x10/100/1000 Mbps LAN - Buttons: 1 Reset button, 1 WPS button - LEDs: 5x Green - Serial Console: unpopulated header 115200 8n1 (silkscreen on PCB) - Power: POE 802.3af (37-57V DC) MAC addresses: +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | LAN | 80:af:ca:xx:xx:x0 | label | | WLAN 2g | 80:af:ca:xx:xx:x0 | label | | WLAN 5g | 82:af:ca:xx:xx:x1 | +1 | +---------+-------------------+-----------+ Installation: The factory firmware is locked: you can only work with Cudy signed firmware. Download a intermediate firmware signed by Cudy here: https://www.cudy.com/blogs/faq/openwrt-software-download After that, login to the router (192.168.10.254, password "admin") and install the intermediate firmware. If you can reach LuCI or SSH now on the intermediate firmware, just use the sysupgrade image with the 'Keep settings' option turned off. Special thanks to Daniel de Kock for starting the porting work at #16265. Signed-off-by: Luis Mita <luis@luismita.com> Co-Authored-By: Daniel de Kock <daniel@riot.network> Co-Authored-By: Hauke Mehrtens <hauke@hauke-m.de> Link: https://github.com/openwrt/openwrt/pull/20268 Signed-off-by: Hauke Mehrtens |
See also
|
|
Categories:
- Cudy
- Embedded system/access point
- Embedded System MediaTek
- Embedded System MT7621DAT
- MediaTek
- Embedded System MIPS 1004Kc
- Embedded System
- Manuf Cudy
- OpenWrt Supported
- Embedded System MT7603EN
- Has Mimo Status
- Embedded System IEEE 802.11b/g/n
- Embedded System MT7613BE
- Embedded System IEEE 802.11a/b/g/n/ac
- Dual-Radio Wireless Embedded System
- Wireless Embedded System
- Dual-Band
- English Documentation