D-Link DAP-1325 rev A1
From TechInfoDepot
Jump to navigationJump to search
| bgn (N300) | |
|---|---|
| N300 Wi-Fi Range Extender | |
 | |
| Homepage | Product page |
| Wikipedia | D-Link |
| 3rd Party Firmware | |
| dd-wrt | Status Unknown |
| OpenWrt | Supported |
| Tomato any flavor | Incompatible |
| Gargoyle | Status Unknown |
| Platform | |
| Brand • Model • Rev | D-Link DAP-1325 rev A1 |
| FCC ID | KA2AP1325A1 |
| Type | range extender |
CPU1  | MediaTek MT7628NN |
| CPU1 Type | MIPS 24KEc |
| CPU1 Speed | 580 MHz |
| Flash1 Chip | Winbond W25Q64JVSSIQ |
| Flash1 Size | 8 MiB 8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> (SPI NOR) |
| RAM1 Size | 64 MiB 67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br /> (DDR2 SDRAM) |
| RAM1 Chip | Brand? Model? |
| ETH chip1 | MediaTek MT7628NN |
| Ethernet Port Count | 1-100MbE-LAN |
| Wired Standard | IEEE 802.3i/3u |
|
802dot11 OUI: none specified | |
| Stock bootloader | U-Boot |
| Expansion IF types | none specified |
| Power | 110-240 VAC ~ 50/60 Hz, ? A |
| Connector type | AC (direct) |
| Serial Port (UART) | yes, 3.3V TTL, (57600 8N1) |
|
| |
|
| |
| Other | |
|
| |
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) |
| Radio 1 | |
| Chip1 | MediaTek MT7628NN |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 2x2:2 |
| Wireless Standard | IEEE 802.11b/g/n |
| 802.11n | up to 300 Mbps |
| 802.11g | up to 54 Mbps |
| 802.11b | up to 11 Mbps |
| WiFi Operating Frequency | 2.4 GHz |
For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.
For a list of all currently documented D-Link devices with specifications, see D-Link.
- • 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.) = N300 class
Overview
The DAP-1325 N300 Wi-Fi Range Extender is a portable plug-in adapter that lets you extend an existing wireless network. Simply place it anywhere in your home to extend the range of your wireless network.
Flashing
 | NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
 | This device is NOT RECOMMENDED for future use with OpenWrt due to low flash/ram.
DO NOT BUY DEVICES WITH 8MB FLASH / 64MB RAM if you intend to flash an up-to-date and secure OpenWrt version onto it! See 8/64 warning for details. This device does not have sufficient resources (flash and/or RAM) to provide secure and reliable operation. This means that you will not be able to install many packages, and that you might experience crashes due to OOM situations more or less often. See OpenWrt on 8/64 devices what you can do now. |
Target: ramips
Subtarget: mt76x8
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 22.03.0
Current supported version: 25.12.2
Subtarget: mt76x8
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 22.03.0
Current supported version: 25.12.2
WLAN Hardware: MediaTek MT7628NN
WLAN Comment: MIMO 2x2:2
Installation method(s):
U-Boot TFTP + serial recovery, U-Boot web recovery, see git-commit
Recovery method(s):
U-Boot TFTP + serial recovery, U-Boot web recovery, see git-commit
WLAN Comment: MIMO 2x2:2
Installation method(s):
U-Boot TFTP + serial recovery, U-Boot web recovery, see git-commit
Recovery method(s):
U-Boot TFTP + serial recovery, U-Boot web recovery, see git-commit
| git • >> |
|---|
ramips: add support for D-Link DAP-1325-A1 This patch adds support for D-Link DAP-1325-A1 (Range Extender Wi-Fi N300) Specifications: - SoC: 580Mhz MT7628NN - RAM: 64MB, DDR2 SDRAM - Storage: 8MB, SPI (W25Q64JVSSIQ) - Ethernet: 1x 10/100 LAN port - WIFI: 2.4 GHz 802.11bgn - LED: Status (2x to provide 3 colors), Wi-Fi Signal Strength (4x) - Buttons: Reset, WPS - UART: Serial console (57600, 8n1) Row of 4 holes near LAN port, starting from square hole: 3.3V, TX,RX,GND - FCC ID: fccid.io/KA2AP1325A1/ Installation: Failsafe UI Firmware can be uploaded with Failsafe UI web page: - turn device off - press and hold reset button - turn device on - keep holding reset until red wifi strength led turns on (ab. 10sec) - connect to device through LAN port PC must be configured with static ip (192.168.0.x) - connect to 192.168.0.50 - select image to be flashed and upload. Device will reboot after successful update Serial port/TFTP server - Connect through serial connectors on PCB (e.g. with teraterm) - Set up a TFTP server, and connect through LAN with static IP - Put image file in the root of the server - Boot the device and select '2' at U-Boot startup - Set device IP, server IP and image file name - Start upload and flash |
JTAG-Serial Info
Serial
Serial Pinouts
Row of 4 holes near LAN port, starting from square hole: 3.3V, TX,RX,GND
