D-Link DAP-1533 rev A1

From TechInfoDepot
Jump to navigationJump to search
abgn (AN900)
Wireless N450 MediaBridge/Access Point
DAP 1533 Angle.png
Support Support page
Wikipedia D-Link
WikiDevi.wi-cat.ru D-Link DAP-1533 rev A1
3rd Party Firmware
dd-wrt Status Unknown
OpenWrt Status Unknown
Tomato any flavor Incompatible
Platform
BrandModelRev D-Link DAP-1533 A1
FCC ID KA2AP1533A1
IC ID 4216A-AP1533A1
Type access point, bridge
CPU1 checkY Atheros AR7370
CPU1 Type MIPS 74Kc
CPU1 Speed 560 MHz
Flash1 Chip Macronix MX25L6406EMI-12G
Flash1 Size 8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br />
RAM1 Size 128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br />
RAM1 Chip ESMT M14D5121632A-2.5B x 2
ETH chip1 Atheros AR7370
Switch Atheros AR8327N
Ethernet Port Count 4-1GbE-LAN
Wired Standard IEEE 802.3i/3u/3ab

802dot11 OUI: none specified

Stock bootloader U-Boot 1.1.4
Stock FW OS Linux 2.6.31 LSDK-9.2.0_U8.834
Expansion IF types USB 2.0
USB ports 1
USB Hub Compatible Untested
Power 12 VDC, 2 A
Connector type barrel
Serial Port (UART) yes, 4-pad header

Flags:
boot log

Other

Default IP address: 192.168.0.50
the IP 192.168.0.50 is used by 62 additional devices
of which 62 are D-Link devices
Default login user: Admin
Default login password: blank
Admin:blank credentials used by 82 additional devices
of which 77 are D-Link devices

Manuf/OEM/ODM Cameo
Retail
Availability common
FCC approval date 09 November 2011
(Est.) release date 20 February 2012
UPC 790069357589
(UPC DB, On eBay)
ASIN B007B5QQX2 Flag of the United States.svg
Radio 1
Chip1 Atheros AR9380
Wireless interface OUI none specified
Antenna Connector Type U.FL
MIMO status 3x3:3
Wireless Standard IEEE 802.11a/b/g/n
802.11n up to 450 Mbps
802.11g up to 54 Mbps
802.11b up to 11 Mbps
802.11a up to 54 Mbps
WiFi Operating Frequency 2.4 or 5 GHz

For a list of all currently documented Atheros (QCA) chipsets with specifications, see Atheros.

For a list of all currently documented D-Link devices with specifications, see D-Link.

450 Mbps - 3SS 5GHz 802.11n (40MHz chan.),
450 Mbps - 3SS 2.4GHz 802.11n (40MHz chan.) = AN900 class

Overview

This device based on an AR7370 with ethernet switch AR8327N. RF based on depopulated an AR9380 5GHz radio. WiFi Certified

JTAG-Serial Info

Serial

Boot log
U-Boot 1.1.4 Rev: 20 (Nov  9 2011 - 19:56:29)

U-boot DB120


DRAM:  128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 162k for U-Boot at: 87fd4000
Reserving 192k for malloc() at: 87fa4000
Reserving 44 Bytes for Board Info at: 87fa3fd4
Reserving 36 Bytes for Global Data at: 87fa3fb0
Reserving 128k for boot params() at: 87f83fb0
Stack Pointer at: 87f83f98
Now running in RAM - U-Boot at: 87fd4000
id read 0x100000ff
flash size 8MB, sector count = 128
Flash:  8 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag934x_enet_initialize...
No valid address in Flash. Using fixed address
 wasp  reset mask:c03300 
WASP  ----> S17 PHY *
: cfg1 0x7 cfg2 0x7114
eth0: 00:03:7f:09:0b:ae
athrs17_reg_init: complete
eth0 up
eth0
Hit any key to stop autoboot:  2  1  0 
## Booting image at 9f030000 ...
   Image Name:   Linux Kernel Image
   Created:      2012-03-13  12:33:41 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1126377 Bytes =  1.1 MB
   Load Address: 80002000
   Entry Point:  8024c9e0
   Verifying Checksum at 0x9f030040 ...OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8024c9e0) ...
## bootargs 0: console=ttyS0,115200 root=31:03 mem=128M rootfstype=squashfs,jffs2 init=/sbin/init mtdparts=ath-nor0:128k(u-boot),64k(nvram),1536k(linux),6144k(rootfs),192k(LANG),64k(MAC),64k(ART)...
## bootargs @A7F83FB0: console=ttyS0,115200 root=31:03 mem=128M rootfstype=squashfs,jffs2 init=/sbin/init mtdparts=ath-nor0:128k(u-boot),64k(nvram),7680k(linux4),6528k@0x00150000(rootfs),192k(LANG),64k(MAC),64k(ART)...
## Giving linux memsize in bytes, 134217728

Starting kernel ...

Booting Atheros AR934x

Linux version 2.6.31--LSDK-9.2.0_U8.834 (root@david-VM) (gcc version 4.3.3 (GCC) ) #25 Tue Mar 13 20:26:18 CST 2012
flash_size passed from bootloader = 8
arg 1: console=ttyS0,115200
arg 2: root=31:03
arg 3: mem=128M
arg 4: rootfstype=squashfs,jffs2
arg 5: init=/sbin/init
arg 6: mtdparts=ath-nor0:128k(u-boot),64k(nvram),7680k(linux4),6528k@0x00150000(rootfs),192k(LANG),64k(MAC),64k(ART)
CPU revision is: 0001974c (MIPS 74Kc)
ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 480 ahb 240
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
User-defined physical RAM map:
 memory: 08000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00008000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00008000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: console=ttyS0,115200 root=31:03 mem=128M rootfstype=squashfs,jffs2 init=/sbin/init mtdparts=ath-nor0:128k(u-boot),64k(nvram),7680k(linux4),6528k@0x00150000(rootfs),192k(LANG),64k(MAC),64k(ART) 
PID hash table entries: 512 (order: 9, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 126464k/131072k available (2376k kernel code, 4424k reserved, 657k data, 144k init, 0k highmem)
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 279.55 BogoMIPS (lpj=559104)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI init:ath_pcibios_init
ath_pcibios_init(294): PCI CMD write: 0x356
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
pci 0000:00:00.0: PME# supported from D0 D1 D3hot
pci 0000:00:00.0: PME# disabled
Returning IRQ 64
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
athwdt_init: Registering WDT success
20000000, 1312D00, USEC_PER_SEC: 1000000,ath_ahb_freq: 240000000
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 247
alg: No test for lzma (lzma-generic)
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered (default)
HDLC line discipline maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
brd: module loaded
7 cmdlinepart partitions found on MTD device ath-nor0
Creating 7 MTD partitions on "ath-nor0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000030000 : "nvram"
0x000000030000-0x0000007b0000 : "linux4"
0x000000150000-0x0000007b0000 : "rootfs"
0x0000007b0000-0x0000007e0000 : "LANG"
0x0000007e0000-0x0000007f0000 : "MAC"
0x0000007f0000-0x000000800000 : "ART"
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
arch/mips/atheros/gpio.c (ath_simple_config_init) JUMPSTART_GPIO: 16
arch/mips/atheros/gpio.c: create_ar531x_gpio_proc_entry: WPS_LED GPIO = 12
ath_otp_init: Registering OTP success
ath_clksw_init: Registering Clock Switch Interface success
VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
Freeing unused kernel memory: 144k freed

init started:  BusyBox v1.01 (2012.03.13-12:30+0000) multi-call binary
init NVRAM_SPACE from mtdblock size
init nvram memory map size: 0x10000 order of pages: 0x4
nvram module init:
/dev/nvram major number 225 glues to mtd: "nvram" size: 0x00010000
nvram_space: 0x00010000 mapped via mmap(2)
openfile :/etc/sysinfo
new ver: 1.0
old ver: 1.0
new ver: 1.0
old ver: 1.0
openfile :/etc/sysinfo
init artblock :lan_mac=28:10:7B:CA:77:15 to "sys_lan_mac"
init artblock :wan_mac=28:10:7B:CA:77:16 to "sys_wan_mac"
init artblock :hw_version=A1 to "sys_hw_version"
init artblock :wlan0_domain=0x37 to "sys_wlan0_domain"
ATHR_GMAC: Length per segment 1536
ATHR_GMAC: fifo cfg 3 01f00140
ATHR_GMAC: RX TASKLET - Pkts per Intr:16
ATHR_GMAC: Mac address for unit 0:bfff0000
ATHR_GMAC: ff:ff:ff:ff:ff:ff 
ATHR_GMAC: Max segments per packet :   1
ATHR_GMAC: Max tx descriptor count :   40
ATHR_GMAC: Max rx descriptor count :   232
ATHR_GMAC: Mac capability flags    :   2381
athr_gmac_ring_alloc Allocated 640 at 0x87a17c00
athr_gmac_ring_alloc Allocated 3712 at 0x879b8000
WASP  ----> S17 PHY *
Setting Drop CRC Errors, Pause Frames and Length Error frames 
### s17 : set 0x610=0x001bd560 
### s17 : set 0x614=0x80010002 
### s17 : set 0x610=0x001b7fe0 
### s17 : set 0x614=0x80020002 
athrs17_reg_init:done
Setting PHY...
Phy setup Complete
[az] 802.3az init done.. 
[az] 802.3az init done.. 
[az] 802.3az init done.. 
[az] 802.3az init done.. 
[az] 802.3az init done.. 
ADDRCONF(NETDEV_UP): eth0: link is not ready
device eth0 is not a slave of br0
interface eth1 does not exist!
device eth0.1 entered promiscuous mode
device eth0 entered promiscuous mode
AR934x GPIO Controller
################ change to AP or Client mode################
nvram_commit: size crc 10000 erasesize:10000, nvram->size: 80251640
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ATH_MAC_TIMER: enet unit:0 is up...
RGMii 1000Mbps full duplex
ATH_MAC_TIMER: done cfg2 0x7215 ifctl 0x0 miictrl  
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Port Status 1c000004 
ath-ehci ath-ehci.0: ATH EHCI
ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000 
ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000 
ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
insmod: cannot open module `/lib/modules/2.6.31--LSDK-9.2.0_U8.834/kernel/drivers/usb/host/ohci-hcd.ko': No such file or directory

Please press Enter to activate this console. ########################## sysinit 
#########################service init 
rc:service_init:init_nvram:start
insmod: cannot insert `/lib/devnvram.ko': File exists (-1): File exists
openfile :/var/etc/nvram.default
rc:service_init:init_nvram:end
configuration_version_control: configuration_version= in NVRAM
configuration_version_control: configuration_version=1.0 in System

=============insert_switch_mod()==============
insert_switch_mod: insmod /lib/modules/2.6.31/net/athrs_gmac.ko
insmod: cannot insert `/lib/modules/2.6.31/net/athrs_gmac.ko': File exists (-1): File exists
device eth0 left promiscuous mode
eth0.1: Cannot assign requested address
device eth0 entered promiscuous mode
eth0.1: Cannot assign requested address
eth0.2: Cannot assign requested address
eth0.2: Cannot assign requested address
device br0 already exists; can't create bridge with the same name
device eth0.1 is already a member of a bridge; can't enslave it to bridge br0.
br0: port 1(eth0.1) entering forwarding state
sh: ./etc/rc.d/pre_customer.sh: not found
Wed Mar 14 17:50:00 UTC 2012
modprobe: could not parse modules.dep

modprobe: could not parse modules.dep

SLIDE on 5GHz Accece Point
/tmp/password has been created
2012-03-14 17:50:00: (network.c.239) warning: please use server.use-ipv6 only for hostnames, not without server.bind / empty address; your config will break if the kernel default for IPV6_V6ONLY changes 
sh: dcc: not found
RC Main Loop: START
rc is BUSY now!
AP Mode or AP Client Mode only need LAN Setting
Start LAN
start_lan():Support AP and Router Mode Switch
killall: udhcpc: no process killed
==========start_ap_lan============
killall: lanmon: no process killed
route_add: ifname=br0,rt_destaddr=0.0.0.0,rt_netmask=0.0.0.0,rt_gateway=192.168.1.1,rt_metric=0
route_add: ifname=lo,rt_destaddr=127.0.0.0,rt_netmask=255.0.0.0,rt_gateway=0.0.0.0,rt_metric=0
##################### wlan1_enable#########################
Loading Wireless Modules: country_Code=276
##########################Loading Wireless Modules: country_Code=276
load DB120
asf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_pci: 9.2.0_U8.834 (Atheros/multi-bss)
__ath_attach: Set global_scn[0]
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
Restoring Cal data from Flash
eepromVersion: 02, templateVersion: 02
custData: 
[ar9300]TxGainTableApply--OSPREY
dfs_attach: use DFS enhancements
DFS min filter rssiThresh = 18
DFS max pulse dur = 151 ticks
ath_get_caps[4834] rx chainmask mismatch actual 7 sc_chainmak 0
ath_get_caps[4809] tx chainmask mismatch actual 7 sc_chainmak 0
SC Callback Registration for wifi0
wifi0: Atheros 9380: mem=0x10000000, irq=64 hw_base=0xb0000000
DFS min filter rssiThresh = 22
DFS max pulse dur = 151 ticks
Loading Wireless Modules: end
set_wlan_mac: start
set_wlan_mac: end
##################### set client mode ###########################
start_makeVAP: ath_count=0, wds_enable=0, apifnum=0:RF:48:11NAHT40MINUS:1, op_mode=AP
start_makeVAP: Ifnum=0, set_RF=RF, Pri_Ch=48, Ch_Mode=11NAHT40MINUS, pure_mode=1, op_mode=AP
wlan_vap_create : enter. devhandle=0x871002c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x871002c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
VAP device ath0 created 
ath0
Invalid command : extoffset
 
 DES SSID SET=dlink 
 ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 
start_makeVAP: end
 
 DES SSID SET=default 
start_activateVAP: ath_count=0, guest_zone=2, netusb_guest_zone=2
device ath0 entered promiscuous mode
br0: port 2(ath0) entering forwarding state
device eth0.1 left promiscuous mode
br0: port 1(eth0.1) entering disabled state
device eth0.1 entered promiscuous mode
br0: port 1(eth0.1) entering forwarding state
Unknown command: 6to4, use subcommands below
  dhcp6c         : dhcp6c command
  rdnssd         : rdnssd command
  autoconfig     : autoconfig mode
  start          : Start AP IPv6 setting
  stop           : Clean AP IPv6 configuration
cli build Dec  9 2011 12:04:53
Unknown command: 6rd, use subcommands below
  dhcp6c         : dhcp6c command
  rdnssd         : rdnssd command
  autoconfig     : autoconfig mode
  start          : Start AP IPv6 setting
  stop           : Clean AP IPv6 configuration
cli build Dec  9 2011 12:04:53
Using Switch Chip to find all mac address
#################################Start WLAN Finished############################
TFTPD start and listen on port 69.
ntp1.dlink.com: Unknown host
usbcore: registered new interface driver sxuptp_generic
usbcore: registered new interface driver sxuptp_ipod
start_route
sh: iptables: not found
sh: iptables: not found
sh: iptables: not found
sh: iptables: not found
sh: iptables: not found
sh: iptables: not found
QoS disabled
Reading topology file /var/tmp/topology.conf ...
409.860: Reading bss configuration file /var/tmp/WSC_ath0.conf ...

 ieee80211_ioctl_siwmode: imr.ifm_active=1376896, new mode=3, valid=1 
br0: port 2(ath0) entering disabled state
Using interface ath0 with hwaddr 28:10:7b:ca:77:15 and ssid 'default'
Failed to kill daemon: No such file or directory
IDLE
rc is IDLE now!
 
 DES SSID SET=default 
br0: port 2(ath0) entering forwarding state
410.661: upnp_wps_device_init called
l2_packet_receive - recvfrom: Network is down

Pictures

User Images