D-Link DGS-1210-28MP rev F1

From TechInfoDepot
Jump to navigationJump to search
multiple revisions of this device, use caution
28-Port Gigabit Smart Managed PoE Switch
Homepage Product page
WikiDevi.wi-cat.ru D-Link DGS-1210-28MP rev F1
3rd Party Firmware
dd-wrt Status Unknown
OpenWrt Supported
Tomato any flavor Incompatible
Gargoyle Status Unknown
Platform
Brand • Model • Rev D-Link DGS-1210-28MP rev F1
Serial Num. prefix S3CH
CPU1 checkY Realtek RTL8382M
CPU1 Type MIPS 4KEc
CPU1 Speed 500 MHz
CPU2 Question? Nuvoton M0516LDE
CPU2 Speed 50 MHz
Flash1 Chip Macronix MX25L25635FMI-10G
Flash1 Size 32 MiB 33,554,432 B <br />262,144 Kib <br />32,768 KiB <br />256 Mib <br />0.0313 GiB <br /> (SPI NOR)
Flash2 Chip Nuvoton M0516LDE
Flash2 Size 64 KiB 0.0625 MiB <br />65,536 B <br />512 Kib <br />0.5 Mib <br />6.103516e-5 GiB <br />
RAM1 Size 128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (DDR3)
RAM1 Chip Nanya NT5CC128M8GN-DI
RAM2 Size 4 KiB 0.00391 MiB <br />4,096 B <br />32 Kib <br />0.0313 Mib <br />3.814697e-6 GiB <br />
RAM2 Chip Nuvoton M0516LDE
ETH chip1 Realtek RTL8382M
ETH chip2 Realtek RTL8218B
ETH chip3 Realtek RTL8218B
ETH chip4 Realtek RTL8214FC
Switch Realtek RTL8382M
Ethernet Port Count 28-1GbE
Ethernet connector 8P8C
Wired Standard IEEE 802.3i/3u/3ab
Auto-MDIX supported
Jumbo frame yes
Switch Class smart

Ethernet OUI: 28:3B:82 (1 E, -)

Expansion IF types SFP
SFP ports 4
PoE 802.3at, 802.3af, standard
Power 100-240 VAC ~ 50/60 Hz, 5.38 A
Connector type C13
Serial Port (UART) yes, 4-pin header, unpopulated, 3.3V TTL, (115200 8N1)
JTAG Port yes, 14-pin header, unpopulated, J3
Other
Flags:
Smart switch, PoE+ switch, SNMP, LACP, MSTP, RSTP, SFP/RJ45 4x Combo port, heatsink, metal case, fan
3rd Party Firmware Support OpenWrt • (List | Dev | DLs)

Additional chips
Digital Temperature Sensor w/ Fan Control;National Semi;LM63;;1;
Octal Int. 802.3bt-Compliant PSE Controller;Broadcom;BCM59121;;3;
Serial Management IF/Shift Register LED Controller;Realtek;RTL8231;;1;
High Speed 10Mbit/s TTL Compatible Optocoupler;LiteOn;LTV-M601;;2;
Single-Phase Synchronous PWM Controller;Anpec;APW8828;;1;
Dual Retriggerable Monostable Multivibrator;NXP;74HC123D;;1;
8-bit Serial-In, Parallel-Out Shift Register;NXP;74HC164D;;8;
30V, 5A Dual P-Channel MOSFET;Alpha & Omega;AO4803;;1;
30V, 50A N-Channel MOSFET;Sinopower;SM3119NA;;1;
30V, 58A N-Channel MOSFET;Sinopower;SM3116NA;;1;
100-V,150-mA Buck Switching Regulator;TI;LM5009A;;1;
3-State Quad Buffer/Line Driver;NXP;74LVC125A;;1;
3-State Octal Buffer/Line Driver;NXP;LVC244A;;1;
1A Silicon Rectifier;SeCoS GmbH;SM4004;;24;
1-Channel Photocoupler;LiteOn;LTV-817;;1;
Quad 2-input AND gate;NXP;74LVC08A;;3;

Retail
(Est.) release date November 2014
Newegg 9SIA25V6X66392
UPC 790069427664
(UPC DB, On eBay)
ASIN B00PVDH7JI
Country of manuf China
 Switch brandSwitch2 brand
D-Link DGS-1210-28 rev F1Realtek
D-Link DGS-1210-28MP rev F1Realtek
D-Link DGS-1210-28P rev F1Realtek

For a list of all currently documented Nuvoton MCU's with specifications, see Nuvoton.
For a list of all currently documented Realtek chipsets with specifications, see Realtek.

For a list of all currently documented D-Link devices with specifications, see D-Link.

Overview

Specifications

  • Processor: Realtek RTL8382M Multi-Layer Managed
Switch Controller w/ Embedded MIPS 4KEc @500MHz
  • Co-processor: Nuvoton M0516LDE to manage PoE
  • Flash/RAM: 32MB (SPI NOR) Flash, 128MB RAM (DDR3)
  • LAN: 24x Gigabit 802.3at PoE Ethernet ports,
4x GbE RJ45/SFP Shared slots,
56Gbps switching capacity
  • PoE: 802.3af, 802.3at (PoE+), 370W PoE budget
  • Rack mountable (1U, 19")

Links of Interest

Revision	Port variants			Hardware platform

A1		10P, 16, 24, 48			Marvell
B1		10P, 20, 28(P), 52		Marvell
C1		10(P), 20, 28(P), 52(P/MP)	Broadcom
F1		10(P/MP), 26, 28(P/MP), 52(MP)	Realtek RTL838x
G1		8P, 10, 16, 24(P), 48		Realtek RTL838x
R1		10(P/MP),26,28(P/MP),52(MP/MPP)	32MB/256MB

Flashing

Flashing OpenWrt

Target: realtek
Subtarget: rtl838x
Package architecture: mips_4kec
Supported Since Commit
Support started version: 23.05.0
Current supported version: 25.12.1
LAN Hardware: Realtek RTL8382M
LAN Comment: Ethernet ports 25-28 are shared with SFP
WLAN Hardware: none
WLAN Comment: No WLAN
Installation method(s):
see git-commit
Recovery method(s):
see devicepage, see git-commit
git • >> 
realtek: d-link: add support for dgs-1210-28mp-f
General hardware info:
----------------------

D-Link DGS-1210-28MP rev. F1 is a switch with 24 ethernet ports and 4
combo ports, all ports Gbit capable. It is based on a RTL8382 SoC @ 500MHz,
DRAM 128MB and 32MB flash. 24 ethernet ports are 802.3af/at PoE capable
with a total PoE power budget of 370W.

Power over Ethernet:
--------------------

The PSE hardware consists of three BCM59121 PSE chips, serving 8 ports
each. They are controlled by a Nuvoton MCU.
In order to enable PoE, the realtek-poe package is required. It is
installed by default, but currently it requires the manual editing of
/etc/config/poe. Keep in mind that the port number assignment does not
match on this switch, alway 8 ports are in reversed order: 8-1, 16-9 and
24-17.

LEDs and Buttons:
-----------------

On stock firmware, the mode button is supposed to switch the LED indicators
of all port LEDs between Link Activity and PoE status. The currently
selected mode is visualized using the respective LEDs. PoE Max indicates
that the maximum PoE budget has been reached.
Since there is currently no support for this behavior, these LEDs and
the mode button can be used independently.

Serial connection:
------------------
The UART for the SoC (115200 8N1) is available via unpopulated standard
0.1" pin header marked J6. Pin1 is marked with arrow and square.

Pin 1: Vcc 3.3V
Pin 2: Tx
Pin 3: Rx
Pin 4: Gnd

OEM installation from Web Interface:
------------------------------------

  1. Make sure you are booting using OEM in image 2 slot. If not, switch to
     image2 using the menus
        System > Firmware Information > Boot from image2
        Tools > reboot
  2. Upload image in vendor firmware via Tools > Backup / Upgrade
     Firmware > image1
  3. Toogle startup image via System > Firmware Information > Boot from
     image1
  4. Tools > reboot

Other installation methods not tested, but since the device shares the
board with the DGS-1210-28, the following should work:

Boot initramfs image from U-Boot:
---------------------------------

  1. Press Escape key during `Hit Esc key to stop autoboot` prompt
  2. Press CTRL+C keys to get into real U-Boot prompt
  3. Init network with `rtk network on` command
  4. Load image with `tftpboot 0x8f000000
     openwrt-rtl838x-generic-d-link_dgs-1210-28mp-f-initramfs-kernel.bin`
     command
  5. Boot the image with `bootm` command

Pictures

Retail Images
User Images
  • PCB, PSU
    PCB, PSU
  • Main board
    Main board
  • PoE board
    PoE board

See also

DGS See also
D-Link DGS series • DSG-1210 series (SH) • DGS-1210 series (ToH)


Retrieved from "https://techinfodepot.shoutwiki.com/w/index.php?title=D-Link_DGS-1210-28MP_rev_F1&oldid=519833"