D-Link DGS-1210-28P rev F1

multiple revisions of this device, use caution
	28-Port Gigabit Smart Managed PoE Switch
Homepage	Product page
WikiDevi.wi-cat.ru	D-Link DGS-1210-28P rev F1
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	D-Link DGS-1210-28P rev F1
CPU1	Realtek RTL8382M
CPU1 Type	MIPS 4KEc
CPU1 Speed	500 MHz
CPU2	Nuvoton M0516LDE
CPU2 Speed	50 MHz
Flash1 Chip	Macronix MX25L25635FMI-10G
Flash1 Size	32 MiB 33,554,432 B <br />262,144 Kib <br />32,768 KiB <br />256 Mib <br />0.0313 GiB <br /> (SPI NOR)
Flash2 Chip	Nuvoton M0516LDE
Flash2 Size	64 KiB 0.0625 MiB <br />65,536 B <br />512 Kib <br />0.5 Mib <br />6.103516e-5 GiB <br />
RAM1 Size	128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (DDR3)
RAM1 Chip	Nanya NT5CC128M8GN-DI
RAM2 Size	4 KiB 0.00391 MiB <br />4,096 B <br />32 Kib <br />0.0313 Mib <br />3.814697e-6 GiB <br />
RAM2 Chip	Nuvoton M0516LDE
ETH chip1	Realtek RTL8382M
ETH chip2	Realtek RTL8218B
ETH chip3	Realtek RTL8218B
ETH chip4	Realtek RTL8214FC
Switch	Realtek RTL8382M
Ethernet Port Count	28-1GbE
Ethernet connector	8P8C
Wired Standard	IEEE 802.3i/3u/3ab
Auto-MDIX	supported
Jumbo frame	yes
Switch Class	smart
	Ethernet OUI: 18:0F:76 (1 E, 1 W)
Expansion IF types	SFP
SFP ports	4
Stock bootloader	U-Boot 2011.12 2.1.5.67086
Stock FW OS	ucLinux 2.6.19
PoE	802.3at, standard
Power	100-240 VAC ~ 50/60 Hz, 3.2 A
Connector type	C13
Serial Port (UART)	yes, 3.3V TTL, (115200 8N1)
JTAG Port	yes, 14-pin header, unpopulated, J3
Other
	Default IP address: 10.90.90.90; the IP 10.90.90.90 is used by 8 additional devices; of which 8 are D-Link devices; Default login user: admin; Default login password: admin; admin:admin credentials used by 1359 additional devices; of which 77 are D-Link devices
	Flags:; smart switch, PoE Switch, SNMP, LACP, MSTP, RSTP, 4x SFP/RJ45 Combo port, heatsink, metal case, fan
3rd Party Firmware Support	OpenWrt • (List \| Dev \| DLs);
	Additional chips; Octal Integrated 802.3bt-Compliant PSE Controller;Broadcom;BCM59121;;3;; Serial Management Interface/Shift register LED Controller;Realtek;RTL8231;;1;; Digital Temperature Sensor w/ Fan Control;National Semiconductor;LM63;;1;; 30V, 5A Dual P-Channel MOSFET;AlphaΩAO4803;;1;; 30V, 50A N-Channel MOSFET;Sinopower;SM3119NA;;2;; Single-phase synchronous PWM Controller;Anpec;APW8828;;1;; 3-State Quad Buffer/Line Driver;NXP;74LVC125A;;1;; 3-State Octal Buffer/Line Driver;NXP;LVC244A;;2;; Quad 2-input AND gate;NXP;74LVC08A;;3;; 8-bit serial-in, parallel-out shift register;NXP;74HC164D;;8;; Dual Retriggerable Monostable Multivibrator;NXP;74HC123D;;1;; 1A Silicon Rectifier;SeCoS GmbH;SM4004;;24;; 1-Channel Photocoupler;Liteon;LTV-817;;1;; High Speed 10MBit/s TTL Compatible Optocoupler;Liteon;LTV-M601;;2;
Retail
(Est.) initial retail price (in USD)	$696
Newegg	9SIAA7WDHE5155
ASIN	B009F7N7B8
Country of manuf	China

For a list of all currently documented Nuvoton MCU's with specifications, see Nuvoton.
For a list of all currently documented Realtek chipsets with specifications, see Realtek.

For a list of all currently documented D-Link devices with specifications, see D-Link.

Overview

Specifications

Processor: Realtek RTL8382M Multi-Layer Managed Switch

Controller with Embedded MIPS 4KEc @500MHz

Co-processor: Nuvoton MO516LDE to manage PoE
Flash/RAM: 32MB (SPI NOR) Flash, 128MB RAM (DDR3)
LAN: 24x Gigabit 802.3at PoE Ethernet ports, 4x Shared GbE RJ45/SFP slots

56Gbps switching capacity

PoE: 802.3af, 802.3at (PoE+), 193W PoE budget
Rack mountable (1U, 19")

Links of Interest

Datasheet (rev F1)
D-Link DGS-1210 series on SvanHeule wiki

Revision	Port variants			Hardware platform

A1		10P, 16, 24, 48			Marvell
B1		10P, 20, 28(P), 52		Marvell
C1		10(P), 20, 28(P), 52(P/MP)	Broadcom
F1		10(P/MP), 26, 28(P/MP), 52(MP)	Realtek RTL838x
G1		8P, 10, 16, 24(P), 48		Realtek RTL838x
R1		10(P/MP),26,28(P/MP),52(MP/MPP)	32MB/256MB

Flashing

NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power.

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)
On the OpenWrt Wiki

Target: realtek
Subtarget: rtl838x
Package architecture: mips_4kec
Supported Since Commit
Support started version: 24.10.0
Current supported version: 25.12.1

LAN Hardware: Realtek RTL8382M
LAN Comment: 24 PoE ports, 4 SFP ports are shared with 4 1Gbit ports
WLAN Comment: No WLAN
Installation method(s):
GUI OEM, see devicepage, see git-commit
Recovery method(s):
see devicepage, see git-commit

git • >>

realtek: d-link: add support for dgs-1210-28p-f
General hardware info:
----------------------

D-Link DGS-1210-28P rev. F1 is a switch with 24 ethernet ports and 4
combo ports, all ports Gbit capable. It is based on a RTL8382 SoC
@500MHz, DRAM 128MB and 32MB flash. 24 ethernet ports are 802.3af/at PoE
capable with a total PoE power budget of 193W.

Power over Ethernet:
--------------------

The PSE hardware consists of three BCM59121 PSE chips, serving 8 ports
each. They are controlled by a Nuvoton MCU.  In order to enable PoE, the
realtek-poe package is required. It is installed by default, but
currently it requires the manual editing of /etc/config/poe. Keep in
mind that the port number assignment does not match on this switch,
alway 8 ports are in reversed order: 8-1, 16-9 and 24-17.

LEDs and Buttons:
-----------------

On stock firmware, the mode button is supposed to switch the LED
indicators of all port LEDs between Link Activity and PoE status. The
currently selected mode is visualized using the respective LEDs. PoE Max
indicates that the maximum PoE budget has been reached.  Since there is
currently no support for this behavior, these LEDs and the mode button
can be used independently.

Serial connection:
------------------
The UART for the SoC (115200 8N1) is available via unpopulated standard
0.1" pin header marked J6. Pin1 is marked with arrow and square.

Pin 1: Vcc 3.3V
Pin 2: Tx
Pin 3: Rx
Pin 4: Gnd

OEM installation from Web Interface:
------------------------------------

    1. Make sure you are booting using OEM in image 2 slot. If not,
       switch to
        image2 using the menus
        System > Firmware Information > Boot from image2
        Tools > reboot
    2. Upload image in vendor firmware via Tools > Backup / Upgrade
        Firmware > image1
    3. Toggle startup image via System > Firmware Information > Boot
       from
        image1
    4. Tools > reboot

Other installation methods not tested, but since the device shares the
board with the DGS-1210-28, the following should work:

Boot initramfs image from U-Boot:
---------------------------------

    1. Press Escape key during `Hit Esc key to stop autoboot` prompt
    2. Press CTRL+C keys to get into real U-Boot prompt
    3. Init network with `rtk network on` command
    4. Load image with `tftpboot 0x8f000000
        openwrt-rtl838x-generic-d-link_dgs-1210-28p-f-initramfs-kernel.bin`
        command
    5. Boot the image with `bootm` command

Pictures

Retail Images

User Images

D-Link DGS-1210-28P rev F1

Overview

Specifications

Links of Interest

Flashing

Flashing OpenWrt

Pictures

See also

Navigation menu

Page actions

Page actions

Personal tools

empty section

Search

Navigation

data/misc

Tools

query forms

Shoutwiki

ShoutWiki messages