D-Link EAGLE PRO AI R32 A1

multiple revisions of this device, use caution

abgn+ac+ax (AX3200)
EAGLE PRO AI AX3200 Smart Router R32
Homepage	Product page
Wikipedia	D-Link
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	D-Link EAGLE PRO AI R32 A1
FCC ID	KA2R32A1
Type	wireless router
CPU1 Y	MediaTek MT7622BV
CPU1 Type	ARM Cortex-A53
CPU1 Speed	1.35 GHz ( 2 cores ) 64-bit
Flash1 Chip	Brand? Model?
Flash1 Size	128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (NAND)
RAM1 Size	512 MiB 536,870,912 B <br />4,194,304 Kib <br />524,288 KiB <br />4,096 Mib <br />0.5 GiB <br />
RAM1 Chip	Brand? Model?
ETH chip1	MediaTek MT7622BV
Switch	MediaTek MT7531BE
Ethernet Port Count	1-1GbE-WAN 4-1GbE-LAN
Wired Standard	IEEE 802.3i/3u/3ab
802dot11 OUI: none specified
Stock bootloader	U-Boot
Expansion IF types	none specified
Power	12 VDC, 2 A
Serial Port (UART)	yes, 3.3V TTL, (115200 8N1)
Flags: Wi-Fi 6, Bluetooth 5.1
Other
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Retail
Availability	End of Life
Radio 1
Chip1	MediaTek MT7975AN
Chip2	MediaTek MT7915AN
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	4x4:4
Wireless Standard	IEEE 802.11b/g/n
n-QAM	up to 800 Mbps
802.11n	up to 600 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
Radio 2
Chip1	MediaTek MT7975AN
Chip2	MediaTek MT7915AN
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	4x4:4
Wireless Standard	IEEE 802.11a/n/ac/ax
802.11ax	up to 2402 Mbps
802.11ac	up to 1733 Mbps
802.11n	up to 600 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz
CPU1 brand Radio1 chip1 brand Radio2 chip1 brand D-Link EAGLE PRO AI M32 A1 MediaTek MediaTek MediaTek D-Link EAGLE PRO AI R15 A1 D-Link EAGLE PRO AI R32 A1 MediaTek MediaTek MediaTek

For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.

For a list of all currently documented D-Link devices with specifications, see D-Link.

• 800 Mbps - 4SS 2.4GHz 802.11n (40MHz chan., 256-QAM),

• 2402 Mbps - 4SS 5GHz 802.11ax (80MHz chan., 1024-QAM) = AX3200 class

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)
On the OpenWrt Wiki

Target: mediatek
Subtarget: mt7622
Package architecture: aarch64_cortex-a53
Supported Since Commit
Support started version: 23.05.2
Current supported version: 24.10.5

LAN Hardware: MediaTek MT7531BE
WLAN Hardware: MediaTek MT7975AN, MediaTek MT7915AN
WLAN Comment: 4x4 2.4ghz 40Mhz channels, 2x2 5ghz 160Mhz channels, Bluetooth 5.1
Installation method(s):
see git-commit
Recovery method(s):
see git-commit

git • >>

mediatek: Add support for D-Link EAGLE PRO AI R32 R32 is like the M32 part of the EAGLE PRO AI series from D-Link. Specification: - MT7622BV SoC with 2.4GHz wifi - MT7975AN + MT7915AN for 5GHz - MT7531BE Switch - 512MB RAM - 128 MB flash - 2 LEDs (Status and Internet, both can be either orange or white) - 2 buttons (WPS and Reset) Compared to M32, the R32 has the following differences: - 4 LAN ports instead of 2 - The recory image starts with DLK6E6015001 instaed of DLK6E6010001 - Individual LEDs for power and internet - MAC address is stored at another offset in the ODM partition MAC addresses: - WAN MAC is stored in partition "Odm" at offset 0x81 - LAN (as printed on the device) is WAN MAC + 1 - WLAN MAC (2.4 GHz) is WAN MAC + 2 - WLAN MAC (5GHz) is WAN MAC + 3 Flashing via Recovery Web Interface: - Set your IP address to 192.168.0.10, subnetmask 255.255.255.0 - Press the reset button while powering on the deivce - Keep the reset button pressed until the internet LED blinks fast - Open a Chromium based and goto http://192.168.0.1 - Download openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-recovery.bin Flashing via uBoot: - Open the case, connect to the UART console - Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router - Run a tftp server which provides openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-initramfs-kernel.bin. - You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later. - Power on the device and select "1. System Load Linux to SDRAM via TFTP." in the boot menu - Enter image file, tftp server IP and device IP (if they differ from the default). - TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start - The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface) - Create a backup of the Kernel1 partition, this file is required if a revert to stock should be done later - Perform a sysupgrade using openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-squashfs-sysupgrade.bin - Reboot the device. OpenWrt should start from flash now Revert back to stock using the Recovery Web Interface: - Set your IP address to 192.168.0.10, subnetmask 255.255.255.0 - Press the reset button while powering on the deivce - Keep the reset button pressed until the internet LED blinks fast - Open a Chromium based and goto http://192.168.0.1 - Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below. Decrypting a D-Link firmware image: - Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c - Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util - Run ./m32-firmware-util R32 --DecryptFactoryImage <OriginalFirmware> <OutputFile> - Example for firmware R32A1_FW103B01: ./m32-firmware-util R32 --DecryptFactoryImage R32A1_FW103B01.bin R32A1_FW103B01.decrypted.bin Revert back to stock using uBoot: - Open the case, connect to the UART console - Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router - Run a tftp server which provides the previously created backup of the Kernel1 partition. - You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later. - Power on the device and select "2. System Load Linux Kernel then write to Flash via TFTP." in the boot menu - Enter image file, tftp server IP and device IP (if they differ from the default). - TFTP download to FLASH will start. After a few seconds the stock firmware should start again There is also an image openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-tftp.bin which can directly be flashed via U-Boot and TFTP. It can be used if no backup of the Kernel1 partition is reuqired. Flahsing via OEM web interface is currently not possible, the OEM images are encrypted. Creating images is only possible manually at the moment. The support for the M32/R32 already includes support for flashing from the OEM web interface: - The device tree contains both partitions (Kernel1 and Kernel2) with conditions to select the correct one based on the kernel command line - The U-Boot variable "boot_part" is set accordingly during startup to finish the partition swap after flashing from the OEM web interface - OpenWrt sysupgrade flashing always uses the partition where it was initially flashed to (no partition swap)