Dell Wireless 2350 Broadband Router (WRTA-108GD)/Serial info

Boot log

boot log • >>

ar531x rev 0x00005850 firmware startup... SDRAM TEST...PASSED Atheros AR5001AP default version 3.4.0.29 auto-booting... Attaching to TFFS... done. Loading /fl/APIMG1...18920 + 1488320 + 105600 Starting at 0x804846e0... /fl/ - Volume is OK Reading Configuration File "/fl/apcfg". Configuration file checksum: 44e94 is good Please check the ethernet cable on port 1! Attaching interface lo0...done ********************************************************** * Initializing Jungo OpenRG * ********************************************************** wireless access point starting... 0x80649510 (openrg): loading license key: Dell 0x80649510 (openrg): Device lmr0 initialized sock_set_sockopt 0: failed setting non-blocking 0x80649510 (openrg): rtinit: wrong ifa (807c1674) was (807c114c) 0x80649510 (openrg): rtinit: wrong ifa (807c1ca4) was (807c1c20) 0x80649510 (openrg): STP: vp256 enters blocking mode 0x80649510 (openrg): rtinit: wrong ifa (807c1ca4) was (807c1c20) Start Main() Lizzy mt_tony Ver is V2.8 Set_nvram(system/network/,initial_setup,1) Get_nvram(dev/br0/static/,ip)=192.168.2.1 Listen packet start Auto Channel Scan selected 2412 MHz, channel 1 wlan1 Ready Ready 0x80633f70 (nashaTaska): STP: vp256 exits blocking mode

Shell

help

wlan1 - ? List of Access Point CLI commands: config wlan -- config wlanX connect bss -- connect to bssX del acl -- Delete Access Control List del key -- Delete Encryption key find bss -- Find BSS find channel -- Find Available Channel find all -- Find All BSS ftp -- Software update via FTP get 11gonly -- Display 11g Only Allowed get 11goptimize -- Display 11g Optimization Level get 11goverlapbss -- Display Overlapping BSS Protection get acl -- Display Access Control List get aging -- Display Aging Interval get antenna -- Display Antenna Diversity get association -- Display Association Table get authentication -- Display Authentication Type get autochannelselect -- Display Auto Channel Select get beaconinterval -- Display Beacon Interval get burstSeqThreshold -- Display Max Number of frames in a Burst get burstTime -- Display Burst Time get channel -- Display Radio Channel get cipher -- Display Encryption cipher get config -- Display Current AP Configuration get countrycode -- Display Country Code get ctsmode -- Display CTS mode get ctsrate -- Display CTS rate get ctstype -- Display CTS type get domainsuffix -- Display Domain Name Server suffix get dtim -- Display Data Beacon Rate (DTIM) get encryption -- Display Encryption Mode get extendedchanmode -- Display Extended Channel Mode get fragmentthreshold -- Display Fragment Threshold get frequency -- Display Radio Frequency (MHz) get gateway -- Display Gateway IP Address get groupkeyupdate -- Display Group Key Update Interval (in Seconds) get hardware -- Display Hardware Revisions get hostipaddr -- Display Host IP Address get ipaddr -- Display IP Address get ipmask -- Display IP Subnet Mask get key -- Display Encryption Key get keyentrymethod -- Display Encyrption Key Entry Method get keysource -- Display Source Of Encryption Keys get login -- Display Login User Name get minimumrate -- Display Minimum Rate get nameaddr -- Display IP address of name server get operationMode -- Display Operation Mode get pktLogEnable -- Display Packet Logging Mode get power -- Display Transmit Power Setting get radiusname -- Display RADIUS server name or IP address get radiusport -- Display RADIUS port number get rate -- Display Data Rate get remoteAp -- Display Remote Ap's Mac Address get rtsthreshold -- Display RTS/CTS Threshold get shortpreamble -- Display Short Preamble Usage get shortslottime -- Display Short Slot Time Usage get sntpserver -- Display SNTP/NTP Server IP Address get ssid -- Display Service Set ID get ssidsuppress -- Display SSID Suppress Mode get station -- Display Station Status get SuperG -- Display SuperG Feature Status get systemname -- Display Access Point System Name get tzone -- Display Time Zone Setting get uptime -- Display UpTime get wirelessmode -- Display Wireless LAN Mode get wlanstate -- Display wlan state help -- Display CLI Command List ping -- Ping pktLog -- Packet Log reboot -- Reboot Access Point run -- Run command file quit -- Logoff set 11gonly -- Set 11g Only Allowed set 11goptimize -- Set 11g Optimization Level set 11goverlapbss -- Set Overlapping BSS Protection set acl -- Set Access Control List set aging -- Set Aging Interval set antenna -- Set Antenna set authentication -- Set Authentication Type set autochannelselect -- Set Auto Channel Selection set beaconinterval -- Modify Beacon Interval set burstSeqThreshold -- Set Max Number of frames in a Burst set burstTime -- Set Burst Time set channel -- Set Radio Channel set cipher -- Set Cipher set countrycode -- Set Country Code set ctsmode -- Set CTS Mode set ctsrate -- Set CTS Rate set ctstype -- Set CTS Type set domainsuffix -- Set Domain Name Server Suffix set dtim -- Set Data Beacon Rate (DTIM) set encryption -- Set Encryption Mode set extendedchanmode -- Set Extended Channel Mode set factorydefault -- Restore to Default Factory Settings set fragmentthreshold -- Set Fragment Threshold set frequency -- Set Radio Frequency (MHz) set gateway -- Set Gateway IP Address set groupkeyupdate -- Set Group Key Update Interval (in Seconds) set hostipaddr -- Set Host IP address set ipaddr -- Set IP Address set ipmask -- Set IP Subnet Mask set key -- Set Encryption Key set keyentrymethod -- Select Encryption Key Entry Method set keysource -- Select Source Of Encryption Keys set login -- Modify Login User Name set minimumrate -- Set Minimum Rate set nameaddress -- Set Name Server IP address set operationMode -- Set operation Mode set password -- Modify Password set passphrase -- Modify Passphrase set pktLogEnable -- Enable Packet Logging set power -- Set Transmit Power set radiusname -- Set RADIUS name or IP address set radiusport -- Set RADIUS port number set radiussecret -- Set RADIUS shared secret set rate -- Set Data Rate set remoteAP -- Set Remote AP's Mac Address set rtsthreshold -- Set RTS/CTS Threshold set shortpreamble -- Set Short Preamble set shortslottime -- Set Short Slot Time set sntpserver -- Set SNTP/NTP Server IP Address set ssid -- Set Service Set ID set ssidsuppress -- Set SSID Suppress Mode set SuperG -- Super G Features set systemname -- Set Access Point System Name set tzone -- Set Time Zone Setting set wlanstate -- Set wlan state set wirelessmode -- Set Wireless LAN Mode timeofday -- Display Current Time of Day version -- Software version rg_cli -- Start OpenRG CLI

get hardware
wlan1 - get hardware wlan1 revisions: mac 5.8 phy 4.4 analog 4.6 PCI Vendor ID: 0x168c, Device ID: 0x13 Sub Vendor ID: 0x168c, Sub Device ID: 0x13 chip is AR2312

version
wlan1 - version AP software 3.4.0.29 openrg@openrg:ar531x Oct 9 2004, 02:58:06

rg_cli help

wlan1 - rg_cli OpenRG help CLI Commands exit Exit from the current cli die <ret> Exit from OpenRG and return ret ps Print OpenRG's tasks rg_conf_print <root> Print OpenRG configuration starting from root - use / for the whole configuration rg_conf_set <path> <value> Set OpenRG configuration path to value rg_conf_set_obscure <path> <value> Set OpenRG configuration path to an obscured value rg_conf_del <path> Delete subtree beginning at path from OpenRG configuration rg_conf_ram_set <path> <value> Set OpenRG dynamic configuration path to value rg_conf_ram_print <root> Print OpenRG's dynamic configuration starting from root - use / for the whole configuration reconf <flash_delay 1(=NOW) to 4> Reconfigure the system according to the current OpenRG configuration entity_close <entity_ptr> Close an entity host <name> Resolve host by name fw_restart Stop & Start Firewall & NAT fw_start Activate Firewall & NAT fw_stop Deactivate Firewall & NAT fw_filter 0 - NAT only, 1 - NAT+filter mac_cache_dump fw_dump [-v] [-ah|-hi] [-c chain | -h address | -i index] [-pr|-ps|-ph|-pm|-pd|-pp] Display firewall rule tree fw_variable [-v] [-a] [-i index | -n name] Display variables of the firewall rules fw_trace Usage: fw_trace <code> - where code is 0 (off), 1 (full), 2 (partial). flash_commit Save OpenRG configuration to flash restore_default [-d] to avoid rebooting after Restore default configuration reboot Reboot the system log_lev_on <severity> Redirect rg_error output equal to or higher than severity to the current console. Severity level values are: 0: Prints debugging messages. 1: Prints informational messages. 2: Prints warning messages. 3: Prints error messages. 4: Prints fatal error messages. 5: Prints fatal error messages and reboots OpenRG. log_lev_off Stop rg_error redirection to the current console rmt_upd Remotely upgrade the box rmt_upd_wget_close Kill a remote upgrade process rg_ifconfig <details_level> print_main_wan Print the name of the current main wan device cat_log [fw|varlog] | e[#buf_num] Print contents of log to console bridge_info Print bridge information flash_layout Print the flash layout and content flash_erase [-d] <section> Erase a given section in the flash flash_dump [-s section | -r address] [-l length] [-1|2|4] Dump the flash content bset Configure bootloader ifconfig Configure network interface ping <ip> Test network connectivity route Print route table load [-u url] [-s section | -r address] Load and burn image ver Display version information etask_list_dump Dump back trace of all etasks sys_ioctl <char_device_type> <command> issue openrg ioctl help [category] to list commands in a category Print a list of command categories Returned 0

rg_cli, ver
OpenRG ver Version: 3.14.14.1.23.18.2 Platform: Atheros AR531x Compilation Time: Sat Oct 9 2004 02:54:41 Compilation Flags: DIST=AR2313_LIZZY Returned 0

rg_cli, flash_layout

OpenRG flash_layout Flash layout: Section 00 Type IMAGE Range 0x00000000-0x002E8000 MaxSize 0x002E7F6C Size 0x00186B9A Name 'Downloaded at: WED JAN 01 00:07:17 2003' Checksum 0x0C5D8D8E Counter 0x00000013 Start Offset 0x00000000 Section 01 Type CONF Range 0x002E8000-0x002F0000 MaxSize 0x00007F6C Size 0x000015E9 Name 'rg_conf' Checksum 0x000AE8EF Counter 0x00000319 Start Offset 0x00000000 Section 02 Type CONF Range 0x002F0000-0x002F8000 MaxSize 0x00007F6C Size 0x000015A9 Name 'rg_conf' Checksum 0x000AD3A9 Counter 0x00000311 Start Offset 0x00000000 Section 03 Type FACTORY Range 0x002F8000-0x002F9000 MaxSize 0x00000F6C Size 0x0000027B Name 'rg_factory' Checksum 0x0000A406 Counter 0x00000023 Start Offset 0x00000000 Total 4 sections found. Returned 0

rg_cli, ps

OpenRG ps OpenRG PS: Entities: eid=0x80585500 type=ENT_WDS t=0x1b ent_status=0x0 next=0x80585530 eid=0x80585530 type=ENT_URL_KEYWORD_FILTER t=0x0 ent_status=0x0 next=0x80585580 eid=0x80585580 type=(null) t=0x0 ent_status=0x0 next=0x805855f0 eid=0x805855f0 type=ENT_HTTP_PROXY t=0x0 ent_status=0x805855d0 next=0x80585680 eid=0x80585680 type=ENT_RMT_UPD t=0x0 ent_status=0x80585650 next=0x80585790 eid=0x80585790 type=ENT_CLI_SERVER t=0x80585760 ent_status=0x0 next=0x80597000 eid=0x80597000 type=ENT_DHCPS t=0x80596fb0 ent_status=0x805dd730 next=0x805dda80 eid=0x805dda80 type=ENT_RMT_MNG_SERVER t=0x0 ent_status=0x805dda60 next=0x805ddbf0 eid=0x805ddbf0 type=ENT_RMT_MNG_SERVER t=0x0 ent_status=0x805ddbd0 next=0x805dde90 eid=0x805dde90 type=ENT_SSI t=0x805dde60 ent_status=0x805ddef0 next=0x805de020 eid=0x805de020 type=ENT_SSI_RMT_UPD_CGI t=0x805ddfc0 ent_status=0x805ddf10 next=0x805de360 eid=0x805de360 type=ENT_HTTPS t=0x805de2c0 ent_status=0x0 next=0x805de4f0 eid=0x805de4f0 type=ENT_TELNET_MASTER_SERVER t=0x0 ent_status=0x805de4d0 next=0x805de560 eid=0x805de560 type=ENT_ROUTE t=0x0 ent_status=0x805de540 next=0x805de650 eid=0x805de650 type=ENT_TODC t=0x0 ent_status=0x805de600 next=0x805de6a0 eid=0x805de6a0 type=ENT_RIP t=0x0 ent_status=0x0 next=0x805de8a0 eid=0x805de8a0 type=ENT_IGD t=0x805de860 ent_status=0x805de880 next=0x805df9d0 eid=0x805df9d0 type=ENT_KLOG t=0x805df9b0 ent_status=0x0 next=0x805e5210 eid=0x805e5210 type=ENT_SYSLOG t=0x805e5140 ent_status=0x805e51d0 next=0x805e5240 eid=0x805e5240 type=ENT_LOGIN t=0x0 ent_status=0x0 next=0x805e52c0 eid=0x805e52c0 type=ENT_DDNS t=0x0 ent_status=0x0 next=0x805e53c0 eid=0x805e53c0 type=ENT_ENTFY t=0x0 ent_status=0x805e53a0 next=0x80289848 eid=0x80289848 type=ENT_FW_RESOLV t=0x0 ent_status=0x0 next=0x802897dc eid=0x802897dc type=ENT_FIREWALL t=0x0 ent_status=0x805e5980 next=0x805ae200 eid=0x805ae200 type=ENT_ERESOLV t=0x0 ent_status=0x0 next=0x805af520 eid=0x805af520 type=ENT_DNS t=0x805e5ad0 ent_status=0x0 next=0x805af900 eid=0x805af900 type=ENT_TIME t=0x0 ent_status=0x805e5d40 next=0x0 Devices: name=br0 type=Bridge eid=0x80597000 type=ENT_DHCPS t=0x80596fb0 ent_status=0x805dd730 next=0x805dda80 name=ae3 type=Ethernet eid=0x80595c30 type=ENT_DHCPC t=0x805962f0 ent_status=0x80595c10 next=0x0 name=ae2 type=Ethernet name=vp256 type=Wireless 802.11g Access Point name=ppp0 type=PPPoE Returned 0