Dynalink DL-WRX36

abgn+ac+ax (AX36002R)
WiFi 6 AX3600 Router
Homepage	Product page
3rd Party Firmware
dd-wrt	Supported
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	Dynalink DL-WRX36
FCC ID	H8NRT5010W-D350
Type	wireless router
CPU1 Y	Qualcomm IPQ8072A
CPU1 Type	ARM Cortex-A53
CPU1 Speed	2.2 GHz ( 4 cores ) 64-bit
Flash1 Chip	Brand? Model?
Flash1 Size	256 MiB 268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br /> (NAND)
RAM1 Size	1 GiB 1,024 MiB <br />1,073,741,824 B <br />8,388,608 Kib <br />1,048,576 KiB <br />8,192 Mib <br /> (DDR4L)
RAM1 Chip	Brand? Model?
ETH chip1	Qualcomm IPQ8072A
ETH chip2	Qualcomm QCA8081
Switch	Qualcomm Atheros QCA8075
Ethernet Port Count	1-2.5GbE-WAN 4-1GbE-LAN
Wired Standard	IEEE 802.3i/3u/3ab/3bz
802.1q vlan	Yes
802dot11 OUI: none specified
Stock bootloader	U-Boot
Expansion IF types	USB 3.0
USB ports	1
USB Hub Compatible	Untested
Power	12 VDC, 2.5 A
Connector type	barrel
Serial Port (UART)	yes, 3.3V TTL, (115200 8N1)
Flags: WiFi 6
Other
Manuf/OEM/ODM	Askey RT5010W
3rd Party Firmware Support	DD-WRT • (List) , OpenWrt • (List | Dev | DLs)
Retail
Availability	End of Life
FCC approval date	05 May 2021
(Est.) release date	03 June 2021
ASIN	B096K9SVCT
Country of manuf	Taiwan
Physical
Dimensions	5.9 x 3.94 x 9.06 inches
Weight	3.47 pounds
Radio 1
Chip1	Qualcomm IPQ8072A
Chip2	Qualcomm QCN5024
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	4x4:4
Wireless Standard	IEEE 802.11b/g/n/ax
802.11ax	up to 1148 Mbps
802.11n	up to 300 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
Radio 2
Chip1	Qualcomm IPQ8072A
Chip2	Qualcomm QCN5054
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	4x4:4
Wireless Standard	IEEE 802.11a/n/ac/ax
802.11ax	up to 2402 Mbps
802.11ac	up to 1733 Mbps
802.11n	up to 600 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz

For a list of all currently documented Qualcomm chipsets with specifications, see Qualcomm.
For a list of all currently documented Qualcomm Atheros (QCA) chipsets with specifications, see Qualcomm Atheros.

• 1148 Mbps - 4SS 2.4GHz 802.11ax (40MHz chan.),

• 2402 Mbps - 4SS 5GHz 802.11ax (80MHz chan.) = AX3600 class

Overview

Dynalink DL-WRX36 is a AX WIFI router with 4 1G and 1 2.5G ports.

Flashing

Flashing dd-wrt

On the DDWRT Wiki
On the DDWRT Forum
Support started version: 56820
Current supported version: ?

Please insert instructions here

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)
On the OpenWrt Wiki
On the OpenWrt Forum

Target: qualcommax
Subtarget: ipq807x
Package architecture: aarch64_cortex-a53
Supported Since Commit
Support started version: 23.05.0
Current supported version: 25.12.2

LAN Hardware: Qualcomm Atheros QCA8075
LAN Comment: Qualcomm Atheros QCA8081 2.5G Phy
WLAN Hardware: Qualcomm QCN5024, Qualcomm QCN5054
WLAN Comment: OFDMA + MU-MIMO, 2.4GHz 2×2/40MHz, 5GHz 4×4/80 or 2×2/160MHz
Install Comment:
Install is 2-stage: initramfs image, then factory image
Comment:
See doc page for USB recovery commands from OpenWrt image

git • >>

ipq807x: add Dynalink DL-WRX36 Dynalink DL-WRX36 is a AX WIFI router with 4 1G and 1 2.5G ports. Specifications: • CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz • RAM: 1024MB of DDR3 • Storage: 256MB Nand • Ethernet: 4x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081) • WLAN: 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 1174 Mbps PHY rate 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate • 1x USB 3.0 • 1 gpio-controlled dual color led (blue/red) • Buttons: 1x soft reset / 1x WPS • Power: 12V DC jack A poulated serial header is onboard (J1004) the connector size is a 4-pin 2.0 mm JST PH. RX/TX is working, u-boot bootwait is active, secure boot is enabled. Notes: - Serial is completely deactivated in the stock firmware image. - This commit adds only single partition support, that means sysupgrade is upgrading the current rootfs partition. - Installation can be done by serial connection or SSH access on OEM firmware Installation Instructions: Most part of the installation is performed from an initramfs image running OpenWrt, and there are two options to boot it. Boot initramfs option 1: Using serial connection (3.3V) 1. Stop auto boot to get to U-boot shell 2. Transfer initramfs image to device (openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb) Tested using TFTP and a FAT-formatted USB flash drive. 3. Boot the initramfs image # bootm Boot initramfs option 2: From SSH access on OEM firmware 1. Copy the initramfs image to a FAT-formatted flash drive (tested on single-partition drive) and connect it to device USB port. 2. Change boot command so it loads the initramfs image on next boot Fallback to OEM firmware is provided. # fw_setenv bootcmd 'usb start && fatload usb 0:1 0x44000000 openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb && bootm 0x44000000; bootipq' 3. Reboot the device to boot the initramfs # reboot Install OpenWrt from initramfs image: 1. Use SCP (or other way) to transfer OpenWrt factory image 2. Connect to device using SSH (on a LAN port) 3. Check MTD partition table. rootfs and rootfs_1 should be mtd18 and mtd20 depending on current OEM slot. # cat /proc/mtd 4. Do a ubiformat to both rootfs partitions: # ubiformat /dev/mtd18 -y -f /path_to/factory_image # ubiformat /dev/mtd20 -y -f /path_to/factory_image 5. Set U-boot env variable: mtdids # fw_setenv mtdids 'nand0=nand0' 6. Get offset of mtd18 to determine current OEM slot - If current OEM slot is 1, offset is 16777216 (0x1000000) - If current OEM slot is 2, offset is 127926272 (0x7a00000) # cat /sys/class/mtd/mtd18/offset 7. Set U-boot env variable: mtdparts If current OEM slot is 1, run: # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x1000000(fs),0x6100000@0x7a00000(fs_1)' If current OEM slot is 2, run: # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x7a00000(fs),0x6100000@0x1000000(fs_1)' 8. Set U-boot env variable: bootcmd # fw_setenv bootcmd 'setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs rootfstype=squashfs rootwait; ubi part fs; ubi read 0x44000000 kernel; bootm 0x44000000#config@rt5010w-d350-rev0' 9. Reboot the device # reboot Note: this PR adds only single partition support, that means sysupgrade is upgrading the current rootfs partition