Edimax 3G-6200n

multiple revisions of this device, use caution

bgn (N150)
wireless router
InfoDepot Wiki	Edimax 3G-6200N
3rd Party Firmware
dd-wrt	Incompatible
OpenWrt	Was Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	Edimax 3G-6200n
FCC ID	NDD9562250817
Type	wireless router
CPU1	Ralink RT3050
CPU1 Type	MIPS 24KEc
CPU1 Speed	320 MHz 16-bit
Flash1 Chip	Macronix 29LV320DBTI-70G
Flash1 Size	4 MiB4,194,304 B <br />32,768 Kib <br />4,096 KiB <br />32 Mib <br />0.00391 GiB <br />
RAM1 Size	32 MiB33,554,432 B <br />262,144 Kib <br />32,768 KiB <br />256 Mib <br />0.0313 GiB <br />
RAM1 Chip	Zentel A3V56S40ETP-G6
ETH chip1	Ralink RT3050
Switch	Ralink RT3050
Ethernet Port Count	1-100MbE-WAN 4-100MbE-LAN
Wired Standard	IEEE 802.3i/3u
802dot11 OUI: 00:1F:1F (4 E, 14 W) Ethernet OUI: 00:1F:1F (4 E, 14 W)
Stock bootloader	U-Boot
Expansion IF types	USB 2.0
USB ports	1
USB Hub Compatible	Untested
Power	12 VDC, 1 A
Connector type	barrel
Serial Port (UART)	yes, (57600 8N1)
JTAG Port	no
Other
Default IP address: 192.168.2.1 the IP 192.168.2.1 is used by 297 additional devices of which 58 are Edimax devices Default login user: admin Default login password: 1234 admin:1234 credentials used by 185 additional devices of which 73 are Edimax devices
Manuf/OEM/ODM	Edimax
3rd Party Firmware Support	OpenWrt (Was)
Retail
FCC approval date	23 February 2009
ASIN	B00EWWE36O
Country of manuf	China
Radio 1
Chip1	Ralink RT3050
Wireless interface OUI	00:1F:1F
Antenna Connector Type	none specified
MIMO status	1x1:1
Wireless Standard	IEEE 802.11b/g/n
802.11n	up to 150 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
FCC ID Edimax BR-6226n NDD9562250817 NDD9562250907
CPU1 brand Radio1 chip1 brand Radio1 chip2 brand Edimax 3G-6200n Ralink Ralink Edimax 3G-6200nL Ralink Ralink

For a list of all currently documented Ralink chipsets with specifications, see Ralink.

For a list of all currently documented Edimax device with specifications, see Edimax.

• 150 Mbps - 1SS 2.4GHz 802.11n (40MHz chan.) = N150 class

Overview

• Edimax 3g-6200n On the DD-WRT Forum

USB 2.0 for 3G/3.5G USB Modem or Printer

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)
On the OpenWrt Wiki
OpenWrt Target: ramips
OpenWrt Subtarget: rt305x
OpenWrt Package architecture: mipsel_24kc
Support started version: 15.05
Current supported version: 19.07.10
Comment:
Image build disabled in master with commit d7d46da938e3
Image too big: 19.07.10

Please insert instructions here

JTAG-Serial Info

Serial

Serial Pinouts

For the record serial seems to be also on JP2
Pins are 3.3V - RXD - GND - TXD
Configuration is: 57600 8 N 1

boot log • >>

*************************************************************************************************************************************************************************************************************************************************** Submarine 1.1.3 (Apr 16 2009 - 10:03:22) Board: Ralink APSoC DRAM: 32 MB relocate-code pointer at: 81fa8000 ************************************ Init GPIO Pin************************************ flash-protect ON: from 0xBFC00000 to 0xBFC262B7 protect on 0 protect on 1 protect on 2 protect on 3 protect on 4 protect on 5 protect on 6 protect on 7 protect on 8 protect on 9 flash-protect ON: from 0xBFC30000 to 0xBFC3FF protect on 10 *** Warning - bad CRC, using default environment Ralink Submarine Version: 3.1 -------------------------------------------------------------- ASIC 3052-MP1 (MAC to GigaMAC Mode) DRAM COMPONENT: 256Mbits DRAM BUS: 16BIT Total memory: 32 MBytes Flash: 4 MBytes Date:Apr 16 2009 Time:10:03:22 icache: sets:256, ways:4, linesz:32,total:32768 dcache: sets:128, ways:4, linesz:32 ,total:16384 The CPU freq - 320 MHz SDRAM bus set to 16 bit SDRAM size Ã32 Mbytes Please choose the operation: 0: Load ucos code to SDRAM via TFTP Client. 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 9: Load Boot Loader code then write to Flash via TFTP. Net: eth register Eth0 (10/100-M) enetvar'ethaddr,Eth addr:00:AA:BB:CC:DD:18 00:AA:BB:CC:DD:18: et-current->name >Em0 (10/100-M) DEBUG BootType 48 0: System Load Boot Loader | F/W then write to Flash via TFTP Client. Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Please Input new ones /or Ctrl-C to discard Input device IP (10.10.10.123) Input server IP (10.10.10.3) Input Li nux Kernel filename (NULL>) netboot-common, argcÃ3 3 ***********buf 0x81fce420 ********NexTxPacket à 81fe64c0 NetTxPacket 0x81FE64C0 NetRxPackets[0] - 0x81FE6AC0 NetRxPackets[1] - 0x81FE70C0 NetRxPackets[2] 0x81FE76C0 NetRxPackets[3] 0x81FE7CC0 NetRxPackets[4] 0x81FE82C0 NetRxPackets[5] 0x81FE88C0 NetRxPackets[6] 0x81FE8EC0 NetRxPackets[7] 0x81FE94C0 NetRxPackets[8] 0x81FE9AC0 NetRxPackets[9] 0x81FEA0C0 NetRxPackets[10] - 0x81FEA6C0 NetRxPackets[11] 0x81FEACC0 NetRxPackets[12] 0x81FEB2C0 NetRxPackets[13] 0x81FEB8C0 NetRxPackets[14] 0x81FEBEC0 NetRxPackets[15] 0x81FEC4C0 NetRxPackets[16] - 0x81FECAC0 NetRxPackets[17] 0x81FED0C0 NetRxPackets[18] 0x81FED6C0 NetRxPackets[19] 0x81FEDCC0 KSEG1ADDR(NetTxPacket) 0xA1FE64C0 NetLoop,call eth-halt ! NetLoop,call ethinit ! Trying Eth0 (10/100-M) Waitting RT2880-RX-DMA-BUSY status Start... done Mac to giga Mac mode Ã...r. à A1FCE840, tx ring0 à A1FCE700 Header Payload scatter function is Disable !! RT2880-PDMA-GLO-CFG-00000020 ******************************************************************* RT2880-RX-CALC-IDX0-19 RT2880-RX-DRX-IDX0 - 0 ******************************************************************* ETH STATE ACTIVE!! Select server or client model: 1/2 server model start SERVER IP address : 192.168.1.6 port:69 Load address: 0x80100000 Loading: * *************************************************************************************************************************************************************************************************************************************************** Submarine 1.1.3 (Apr 16 2009 - 10:03:22) Board: Ralink APSoC DRAM: 32 MB relocate-code pointer at: 81fa8000 ************************************ Init GPIO Pin************************************ flash-protect ON: from 0xBFC00000 to 0xBFC262B7 protect on 0 protect on 1 protect on 2 protect on 3 protect on 4 protect on 5 protect on 6 protect on 7 protect on 8 protect on 9 flash-protect ON: from 0xBFC30000 to 0xBFC3FF protect on 10 *** Warning - bad CRC, using default environment Ralink Submarine Version: 3.1 -------------------------------------------------------------- ASIC 3052-MP1 (MAC to GigaMAC Mode) DRAM COMPONENT: 256Mbits DRAM BUS: 16BIT Total memory: 32 MBytes Flash: 4 MBytes Date:Apr 16 2009 Time:10:03:22 icache: sets:256, ways:4, linesz:32,total:32768 dcache: sets:128, ways:4, linesz:32 ,total:16384 The CPU freq - 320 MHz SDRAM bus set to 16 bit SDRAM size Ã32 Mbytes Please choose the operation: 0: Load ucos code to SDRAM via TFTP Client. 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 9: Load Boot Loader code then write to Flash via TFTP. You choosed 3 0 0 3: System boot system code via Flash. Booting image at bfc50000 ... Bad Magic Number,43535953 Image name: Linux Kernel Image Created: 2009-11-03 9:38:24 UTC System Control status 0x20400000 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 3653548 bytes à 3.5 MB Load Address: 80000000 Entry Point: 802bc000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd Transferring control to Linux (at address 802bc000) ... Giving linux memsize in MB, 32 Starting kernel ... LINUX started... THIS IS ASIC Linux version 2.6.21 (root-vance.localdomain) (gcc version 3.4.2) 17:30:33 CST 2009 The CPU feqenuce set to 320 MHz CPU revision is: 0001964c Determined physical RAM map: memory: 02000000 à 00000000 (usable) Built 1 zonelists. Total pages: 8128 Kernel command line: console-ttyS1.57600n8 root/env/mtdblock4 Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). Cache parity protection disabled cause à 80800034, status à 1100ff00 PID hash table entries: 128 (order: 7, 512 bytes) calculating r4... 00138800(1280000) CPU frequency 320.00 MHz Using 160.000 MHz high precision timer. Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 29468k/32768k available (2266k kernel code, 3300k reserved, 529k data, 1 16k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Time: MIPS clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher squashfs: LZMA suppport for slax.org by jro io scheduler noop registered (default) FLASH-API: MAN-ID-C2 DEV-ID-22A8 SIZE-4MB ***********Init LED Driver************* Init GPIO Pin Init GPIO Direction Init GPIO Interrupt ***********Init LED Driver Finishing********* RalinkÃ3gpio-init-irq LED & GPIO & LAN Status Driver LED VERSION HDLC line discipline: version Ã...Revision: 1.1.1.1, maxframe 4096 N-HDLC line discipline registered. Serial: 8250/16550 driver - Revision: 1.3 - 2 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0xb0000500 (irq à 37) is a 16550A serial8250: ttyS1 at I/O 0xb0000c00 (irq à 12) is a 16550A loop: loaded (max 8 devices) rdmÃ3major à 254 GDMA1-MAC-ADRH -- 0x00000000 GDMA1-MAC-ADRL -- 0x00000000 Ralink APSoC Ethernet Driver Initilization. v1.60 256 rx/tx descriptors allocat ed, mtu à 1500! GDMA1-MAC-ADRH -- 0x0000000c GDMA1-MAC-ADRL -- : 0x43305277 PROC INIT OK! PPP generic driver version 2.4.2 PPP BSD Compression module registered NET: Registered protocol family 24 ralink flash device: 0x1000000 at 0xbf000000 Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 number of CFI chips: 1 cfi-cmdset-0002: Disabling erase-suspend-program due to code brokenness. Creating 7 MTD partitions on "Ralink SoC physically mapped flash": 0x00000000-0x00030000 : "Boot Loader" mtd: Giving out device 0 to Bootloader 0x00030000-0x00040000 : "Config " mtd: Giving out device 1 to Config 0x00040000-0x00050000 : "Factory" mtd: Giving out device 2 to Factory 0x00050000-0x00160000 : "Kernel" mtd: Giving out device 3 to Kernel 0x00160000-0x003e0000 : "RootFS" mtd: Giving out device 4 to RootFS 0x003e0000-0x00400000 : "Cimage" mtd: Giving out device 5 to Cimage 0x00050000-0x003e0000 : "Uimage" mtd: Giving out device 6 to Uimage block2mtd: version >Revision: 1.1.1.1 usbcore: registered new interface driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver dwc-otg: version 2.60a 22-NOV-2006 DWC-otg: Using DMA mode dwc-otg lm0: DWC OTG Controller dwc-otg lm0: new USB bus registered, assigned bus number 1 dwc'otg lm0: irq 18, io mem 0x00000000 DWCÃotg: Init: Port Power? opÃ3stateÃ1 DWC-otg: Init: Power Port (0) usb usb1: Product: DWC OTG Controller usb usb1:  Manufacturer: Linux 2.6.21 dwcÃotgÃ3hcd usb usb1: SerialNumber: lm0 usb usb1: configuration Ã1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected u32 classifier Performance counters on nfÃ3conntrack version 0.5.0 (256 buckets, 2048 max) ip tables: (C) 2000-2006 Netfilter Core Team, Type-Restricted Cone ClusterIP Version 0.8 loaded successfully arp tables: (C) 2002 David S. Miller ipt 'time loading TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 802.1Q VLAN Support v1.8 Ben Greear Ã...greearbÃ3candelatech.com> All bugs added by David S. Miller Ã...davemÃ3redhat.com> VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 116k freed init started: BusyBox v1.11.1 (2009-11-03 17:37:25 CST) starting pid 606, tty '': '/etc/rc.sh' Cannot run '/etc/rc.sh': No search file or directory starting pid 607, tty '': '-/bin/sh'console. Algorithmics/MIPS FPU Emulator v1.5 BusyBox v1.11.1 (2009-11-03 17:37:25 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. Sat Jan 1 00:00:00 UTC 2000 killall: pptp.sh: no process killed killall: pppoe.sh: no process killed killall: failover.sh: no process killed ifconfig: 0.0.0.0: error fetching interface information: Device not found 0x01d25000, tx ring 0xa1d25000, size: 16 bytes phy'rx'ring à 0x01d26000, rx ring à 0xa1d26000, size: 16 bytes RT305x-ESW: Link Status Changed GDMA1 FWD CFG - 710000 ra2880stop()...Done Free TX/RX ring memory! GDMA1-MAC-ADRH -- : 0x0000001f GDMA1-MAC-ADRL -- : 0x1f6d80fc 0x01cdb000, tx ring 0xa1cdb000, size: 16 bytes phy'rx'ring à 0x01cdc000, rx ring à 0xa1cdc000, size: 16 bytes GDMA1 FWD CFG - 710000 eth2.1: Setting MAC address to 00 1f 1f 6d 80 fc. VLAN (eth2.1): Underlying device (eth2) has same MAC, not checking promiscious mode. eth2.2: Setting MAC address to 00 0f ea c4 35 3c. device eth2 entered promiscuous mode WiFi (eth2.2): Setting underlying device (eth2) to promiscious mode. Initialize WLAN interface Setup BRIDGE interface ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device bridge br0 doesn't exist; can't delete it Setup bridge... device eth2.1 entered promiscuous mode eth2.1: dev'set promiscuity(master,1) route: ioctl 0x890c failed: No search process br0: port 1(eth2.1) entering learning state br0: topology change detected, propagating br0: port 1(eth2.1) entering forwarding state route: ioctl 0x890c failed: No search process route: ioctl 0x890c failed: No search process ------> 802.1x------>Enter ------> 802.1x------>Exit Static DHCP Leases disable! route: ioctl 0x890c failed: No search process device eth2 is not a slave of br0 device eth2.1 is already a member of a bridge; can't enslave it to bridge br0. switch reg write offset-14, value 405555 switch reg write offset, value-2001 switch reg write offset-98, value-7f3f switch reg write offset-40, value-1001 switch reg write offset 44, value-1001 switch reg write offset-48, value-1002 switch reg write offset 70, value-ffff506f Set: phy[0].reg[0] à b100 Set: phy[1].reg[0] Set: phy[2].reg[0] Set: phy[3].reg[0] à b100 Set: phy[4].reg[0] à b100 ************************************************************************************************************************** * Running Diagd * ************************************************************************************************************************** ************************************************************************************************************************** * Enable WSC-UPnP * ************************************************************************************************************************** /bin/init.sh: line 522: wscd: not found ************************************************************************************************************************** * Enable LLTD * ************************************************************************************************************************** killall: snmpd: no process killed killall: lld2d: no process killed ************************************************************************************************************************** * Enable GPIO Interrupt * ************************************************************************************************************************** ralink-gpio:ioctl GPIO REG ralink-gpio:ioctl GPIO REG killall: watchdog.sh: no process killed ip table: set wan-name-eth2.2 killall: radiusd: no process killed RADIUS server disable !! kill: you need to specify whom to kill ************************************************************************************************************************** * FREE Page,Dentries and Inodes Cache * ************************************************************************************************************************** MemFree: 23608 kB Cached: 1340 kB killall: pppd: no process killed killall: pptp.sh: no process killed killall: pppoe.sh: no process killed ifconfig: 0.0.0.0: error fetching interface information: Device not found Setup WAN interface ifconfig: 0.0.0.0: error fetching interface information: Device not found device eth2 is not a slave of br0 device eth2.1 is already a member of a bridge; can't enslave it to bridge br0. switch reg write offset-14, value 405555 switch reg write offset, value-2001 switch reg write offset-98, value-7f3f switch reg write offset-40, value-1001 switch reg write offset 44, value-1001 switch reg write offset-48, value-1002 switch reg write offset 70, value-ffff506f Set: phy[0].reg[0] à b100 Set: phy[1].reg[0] Set: phy[2].reg[0] Set: phy[3].reg[0] à b100 Set: phy[4].reg[0] à b100 udhcpc (v1.11.1) started rm: cannot remove '/tmp/agentenabledflag': No such file or directory /bin/start-wan.sh: line 265: /bin/agent: nip table: set wan-name-eth2.2 ot found killall: modemctl: no process killed ralink-gpio:ioctl GPIO REG ralink-gpio:ioctl GPIO REG into eth2.2.deconfig killall: snmpd: no process killed