Elecom WAB-S1167-PS

From TechInfoDepot
Jump to navigationJump to search
abgn+ac (AC1200)
AC1200 Access Point
3rd Party Firmware
dd-wrt Status Unknown
OpenWrt Supported
Tomato any flavor Incompatible
Gargoyle Status Unknown
Platform
Brand • Model • Rev Elecom WAB-S1167-PS
FCC ID none specified
JVN 24885537
Type access point
CPU1 checkY Qualcomm Atheros QCA9557
CPU1 Type MIPS 74Kc
CPU1 Speed not specified
Flash1 Chip Macronix MX25L12835FMI-10G
Flash1 Size 16 MiB 16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> (SPI NOR)
RAM1 Size 128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (DDR2)
RAM1 Chip Winbond W9751G6KB251 x 2
ETH chip1 Qualcomm Atheros QCA9557
ETH chip2 Atheros AR8035
ETH chip3 Atheros AR8033
Ethernet Port Count 2-1GbE-LAN
Wired Standard IEEE 802.3i/3u/3ab

802dot11 OUI: 00:90:FE (1 E, 2 W)
Ethernet OUI: 00:90:FE (1 E, 2 W)

Stock bootloader U-Boot
Expansion IF types USB 2.0
USB ports 1
USB Hub Compatible Untested
PoE 802.3at, 802.3af, standard
Power 12 VDC, 1 A
Serial Port (UART) yes, 3.3V TTL, (115200 8N1)
Other
3rd Party Firmware Support OpenWrt • (List | Dev | DLs)
Retail
Availability End of Life
Radio 1
Chip1 Qualcomm Atheros QCA9557
Wireless interface OUI 00:90:FE
Antenna Connector Type none specified
MIMO status 2x2:2
Wireless Standard IEEE 802.11b/g/n
802.11n up to 300 Mbps
802.11g up to 54 Mbps
802.11b up to 11 Mbps
WiFi Operating Frequency 2.4 GHz
Radio 2
Chip1 Qualcomm Atheros QCA9882
Wireless interface OUI 00:90:FE
Antenna Connector Type none specified
MIMO status 2x2:2
Wireless Standard IEEE 802.11a/n/ac
802.11ac up to 867 Mbps
802.11n up to 300 Mbps
802.11a up to 54 Mbps
WiFi Operating Frequency 5 GHz

For a list of all currently documented Atheros (QCA) chipsets with specifications, see Atheros.
For a list of all currently documented Qualcomm Atheros (QCA) chipsets with specifications, see Qualcomm Atheros.

For a list of all currently documented Elecom devices with specifications, see Elecom.

• 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.),
• 867 Mbps - 2SS 5GHz 802.11ac (80MHz chan.) = AC1200 class

Flashing

Flashing OpenWrt

Target: ath79
Subtarget: generic
Package architecture: mips_24kc
Supported Since Commit
Support started version: 24.10.0
Current supported version: 25.12.5
LAN Comment: Supports 802.3af supply on PSE (downstream) port when powered by DC adapter or 802.3at PoE
WLAN Comment: Qualcomm Atheros QCA9557, Qualcomm Atheros QCA9882, 2.4/5 GHz 2T2R
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
git • >> 
ath79: add support for ELECOM WAB-S1167-PS
ELECOM WAB-S1167-PS is a 2.4/5 GHz band 11ac (Wi-Fi 5) access point,
based on QCA9557.

Specification:

- SoC              : Qualcomm Atheros QCA9557
- RAM              : DDR2 128 MiB (2x Winbond W9751G6KB251)
- Flash            : SPI-NOR 16 MiB (Macronix MX25L12835FMI-10G)
- WLAN             : 2.4/5 GHz 2T2R
  - 2.4 GHz        : Qualcomm Atheros QCA9557 (SoC)
  - 5 GHz          : Qualcomm Atheros QCA9882
- Ethernet         : 2x 10/100/1000 Mbps
  - phy ("PD")     : Atheros AR8035
  - phy ("PSE")    : Atheros AR8033
- LEDs/keys (GPIO) : 3x/3x
- UART             : 1x RJ-45 port
  - "SERVICE"      : TTL (3.3V)
    - port         : ttyS0
    - assignment   : 1:3.3V, 2:GND, 3:TX, 4:RX
    - settings     : 115200n8
    - note         : no compatibility with "Cisco console cable"
- Buzzer           : 1x GPIO-controlled
- USB              : 1x USB 2.0 Type-A
- Power            : DC jack or PoE
  - DC jack        : 12 VDC, 1 A (device only, rating)
  - PoE            : 802.3af/at, 48 VDC, 0.25 A (device only, rating)
  - note           : supports 802.3af supply on PSE (downstream) port
                     when powered by DC adapter or 802.3at PoE

Flash instruction using factory.bin image:

1. Boot WAB-S1167-PS without no upstream connection (or PoE connection
   without DHCP)
2. Access to the WebUI ("http://192.168.3.1") on the device and open
   firmware update page
   ("ツールボックス" -> "ファームウェア更新")
3. Select the OpenWrt factory.bin image and click update
   ("アップデート") button
4. Wait ~120 seconds to complete flashing

Revert to OEM firmware:

1. Download the latest OEM firmware
2. Remove 128 bytes(0x80) header from firmware image
3. Decode by xor with a pattern "8844a2d168b45a2d" (hex val)
4. Upload the decoded firmware to the device
5. Flash to "firmware" partition by mtd command
6. Reboot

Notes:

- To use the "SERVICE" port, the connection of 3.3V line is also
  required to enable console output.
  The uart line of "SERVICE" is branched out from the internal pin
  header with 74HC126D and 3.3V line is connected to OE pin on it.

- The same PCB is used with WAB-S600-PS.

- To supply 802.3af PoE on "PSE" port when powered by DC adapter, 12 VDC
  3.5 A adapter is recommended. (official: WAB-EX-ADP1)

MAC addresses:

Ethernet (PD, PSE): 00:90:FE:xx:xx:04 (Config, ethaddr (text))
2.4GHz            : 00:90:FE:xx:xx:04 (Config, ethaddr (text))
5GHz              : 00:90:FE:xx:xx:05
Retrieved from "https://techinfodepot.shoutwiki.com/w/index.php?title=Elecom_WAB-S1167-PS&oldid=538623"