Elecom WRC-X3200GST3
From TechInfoDepot
Jump to navigationJump to search
| abgn+ac+ax (AX3200) | |
|---|---|
| Wi-Fi 6(11ax) 2402+800Mbps Wi-Fi Gigabit Router | |
|
| |
| Homepage | Product page |
| 3rd Party Firmware | |
| dd-wrt | Status Unknown |
| OpenWrt | Supported |
| Tomato any flavor | Incompatible |
| Gargoyle | Status Unknown |
| Platform | |
| Brand • Model • Rev | Elecom WRC-X3200GST3 |
| FCC ID (fcc.io) | none specified |
| FCC ID (fcc.report) | none specified |
| Type | wireless router |
| CPU1 | MediaTek MT7622B |
| CPU1 Type | ARM Cortex-A53 |
| CPU1 Speed | 1.35 GHz ( 2 cores ) 64-bit |
| Flash1 Chip | Winbond W25N01GVZEIG |
| Flash1 Size | 128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (SPI NAND) |
| RAM1 Size | 512 MiB 536,870,912 B <br />4,194,304 Kib <br />524,288 KiB <br />4,096 Mib <br />0.5 GiB <br /> (DDR3) |
| RAM1 Chip | Nanya NT5CC256M16ER-EK |
| ETH chip1 | MediaTek MT7622B |
| Switch | MediaTek MT7531 |
| Ethernet Port Count |
1-1GbE-WAN 4-1GbE-LAN |
| Wired Standard | IEEE 802.3i/3u/3ab |
|
802dot11 OUI: none specified | |
| Stock bootloader | U-Boot |
| Expansion IF types | none specified |
| Power | 12 VDC, 1.5 A |
| Serial Port (UART) | yes, 3.3V TTL, (115200 8N1) |
|
| |
|
| |
| Other | |
|
| |
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) |
| Retail | |
| Availability | End of Life |
| Radio 1 | |
| Chip1 | MediaTek MT7622B |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 4x4:4 |
| Wireless Standard | IEEE 802.11b/g/n |
| N-QAM | up to 800 Mbps |
| 802.11n | up to 600 Mbps |
| 802.11g | up to 54 Mbps |
| 802.11b | up to 11 Mbps |
| WiFi Operating Frequency | 2.4 GHz |
| Radio 2 | |
| Chip1 | MediaTek MT7915A |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 4x4:4 |
| Wireless Standard | IEEE 802.11a/n/ac/ax |
| 802.11ax | up to 2402 Mbps |
| 802.11ac | up to 1733 Mbps |
| 802.11n | up to 600 Mbps |
| 802.11a | up to 54 Mbps |
| WiFi Operating Frequency | 5 GHz |
For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.
For a list of all currently documented Elecom devices with specifications, see Elecom.
Flashing
| NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
Target: mediatek
Subtarget: mt7622
Package architecture: aarch64_cortex-a53
Supported Since Commit
Support started version: 23.05.0
Current supported version: 24.10.5
Subtarget: mt7622
Package architecture: aarch64_cortex-a53
Supported Since Commit
Support started version: 23.05.0
Current supported version: 24.10.5
LAN Hardware: MediaTek MT7531
WLAN Hardware: MediaTek MT7622B, MediaTek MT7915A
Installation method(s):
GUI OEM, see git-commit
WLAN Hardware: MediaTek MT7622B, MediaTek MT7915A
Installation method(s):
GUI OEM, see git-commit
| git • >> |
|---|
mediatek: mt7622: add support for ELECOM WRC-X3200GST3
ELECOM WRC-X3200GST3 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
MT7622B.
Specifications:
- SoC : MediaTek MT7622B
- RAM : DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
- Flash : SPI-NAND 128 MiB (Winbond W25N01GVZEIG)
- WLAN : 2.4/5 GHz 4T4R
- 2.4 GHz : MediaTek MT7622B (SoC)
- 5 GHz : MediaTek MT7915A
- Ethernet : 5x 10/100/1000 Mbps
- Switch : MediaTek MT7531
- LEDs/Keys : 6x/4x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J19: 3.3V, GND, TX, RX from power jack side
- 115200n8
- Power : 12 VDC, 1.5 A
Flash instruction using factory image:
1. Boot WRC-X3200GST3 normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing
MAC Addresses:
LAN : 04:AB:18:xx:xx:77 (Factory, 0x7FFF4 (hex))
WAN : 04:AB:18:xx:xx:78 (Factory, 0x7FFFA (hex))
2.4 GHz: 04:AB:18:xx:xx:79 (Factory, 0x4 (hex))
5 GHz : 04:AB:18:xx:xx:7A (none)
Note:
- currently, there is no "phy1tpt" trigger for 5 GHz wlan (MT7915) in
"trigger" file of LEDs, use "phy1radio" trigger instead
|
Categories:
- Elecom
- Embedded system/wireless router
- Embedded System MediaTek
- Embedded System MT7622B
- MediaTek
- Embedded System ARM
- Embedded System Cortex-A53
- Embedded System MT7531
- OpenWrt Supported
- Has Mimo Status
- Embedded System IEEE 802.11b/g/n
- Embedded System MT7915A
- Embedded System IEEE 802.11a/n/ac/ax
- Dual-Radio Wireless Embedded System
- Wireless Embedded System
- Dual-Band
- Embedded System
- English Documentation