Fon Wireless FON2501A
From TechInfoDepot
Jump to navigationJump to searchabgn (AN600) | |||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Wireless Dual-Band Router | |||||||||||||
WikiDevi.wi-cat.ru | |||||||||||||
3rd Party Firmware | |||||||||||||
dd-wrt |
Status Unknown | ||||||||||||
OpenWrt |
Status Unknown | ||||||||||||
Tomato any flavor |
Status Unknown | ||||||||||||
Platform | |||||||||||||
Brand • Model • Rev |
Fon Wireless FON2501A | ||||||||||||
FCC ID | |||||||||||||
Type |
wireless router | ||||||||||||
CPU1 |
Broadcom BCM5358UB0 | ||||||||||||
CPU1 Type |
MIPS 74K | ||||||||||||
CPU1 Speed |
530 MHz | ||||||||||||
Flash1 Chip |
Brand? Model? | ||||||||||||
Flash1 Size |
8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> | ||||||||||||
RAM1 Size |
64 MiB67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br /> | ||||||||||||
RAM1 Chip |
Brand? Model? | ||||||||||||
ETH chip1 |
Broadcom BCM5358UB0 | ||||||||||||
Switch |
Broadcom BCM5358UB0 | ||||||||||||
Ethernet Port Count |
1-100MbE-WAN 2-100MbE-LAN | ||||||||||||
Wired Standard |
IEEE 802.3i/3u | ||||||||||||
802dot11 OUI: none specified | |||||||||||||
Stock FW OS |
Linux 2.6.22 | ||||||||||||
Expansion IF types |
USB 2.0 | ||||||||||||
USB ports |
1 | ||||||||||||
USB Hub Compatible |
Untested | ||||||||||||
Power |
12 VDC, 1 A | ||||||||||||
Connector type |
barrel | ||||||||||||
Other | |||||||||||||
Default IP address: 192.168.10.1 | |||||||||||||
Manuf/OEM/ODM |
Arcadyan WG8016 G22-AK | ||||||||||||
Retail | |||||||||||||
FCC approval date | 29 August 2013 | ||||||||||||
Country of manuf | China | ||||||||||||
Radio 1 | |||||||||||||
Chip1 |
Broadcom BCM5358UB0 | ||||||||||||
Wireless interface OUI |
none specified | ||||||||||||
Antenna Connector Type |
none specified | ||||||||||||
MIMO status |
2x2:2 | ||||||||||||
Wireless Standard |
IEEE 802.11b/g/n | ||||||||||||
802.11n |
up to 300 Mbps | ||||||||||||
802.11g |
up to 54 Mbps | ||||||||||||
802.11b |
up to 11 Mbps | ||||||||||||
WiFi Operating Frequency |
2.4 GHz | ||||||||||||
Radio cor_rev |
28 | ||||||||||||
Radio 2 | |||||||||||||
Chip1 |
Broadcom BCM43236B | ||||||||||||
Wireless interface OUI |
none specified | ||||||||||||
Antenna Connector Type |
none specified | ||||||||||||
MIMO status |
2x2:2 | ||||||||||||
Wireless Standard |
IEEE 802.11a/n | ||||||||||||
802.11n |
up to 300 Mbps | ||||||||||||
802.11a |
up to 54 Mbps | ||||||||||||
WiFi Operating Frequency |
5 GHz | ||||||||||||
| |||||||||||||
|
For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.
Overview
This device seems to be BCM5358UB0 + BCM43236B.
- CPU: Broadcom BCM5358UB0KFBG (SoC, 2T2R 2.4GHz)
- WLAN: Broadcom BCM43236BKMLG (USB, 2T2R 5GHz)
- Antenna: 2x external 2.14dBi antennas
- Port: 1x WAN, 2x LAN, FE 10/100Mbps
- USB: 1x USB 2.0 Host
- Buttons: 1x Reset, 1x WPS button
Links of Interest
JTAG-Serial Info
Serial
Serial Pinouts
1 -> +3.3v 2 -> Tx 3 -> Rx 4 -> GND
boot log |
---|
Decompressing...done Init Arena Init Devs. Boot partition size = 131072(0x20000) Found a 8MB ST compatible serial flash et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.70.55.34 @VERSION_TYPE@ CPU type 0x19749: 530MHz Tot mem: 65536 KBytes CFE mem: 0x80700000 - 0x807A14B0 (660656) Data: 0x80736F90 - 0x8073A1D0 (12864) BSS: 0x8073A1D0 - 0x8073B4B0 (4832) Heap: 0x8073B4B0 - 0x8079F4B0 (409600) Stack: 0x8079F4B0 - 0x807A14B0 (8192) Text: 0x80700000 - 0x80736F8C (225164) Copying boot params..... DONE Bootloader version v0.03 boot_version v0.03 Project name : WG8016G22-AK Press space bar to cancel startup... Device eth0: hwaddr XX-XX-XX-XX-XX-XX, ipaddr 192.168.10.1, mask 255.255.255.0 gateway not set, nameserver not set Loader:raw Filesys:raw Dev:flash0.os File: Options:(null) Loading: ........ 4404344 bytes read Entry at 0x80001000 Closing network. Starting program at 0x80001000 Linux version 2.6.22-gbc0f0874-dirty (wenfang@localhost.localdomain) (gcc version 4.1.2) #3 Wed Sep 25 08:54:25 CST 2013 CPU revision is: 00019749 Found a 8MB ST compatible serial flash wombo_reset set to gpio 22 Determined physical RAM map: memory: 04000000 @ 00000000 (usable) Built 1 zonelists. Total pages: 16256 Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 256 (order: 8, 1024 bytes) CPU: BCM5357 rev 2 at 530 MHz Using 265.000 MHz high precision timer. Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 60152k/65536k available (2947k kernel code, 5328k reserved, 1177k data, 176k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: no core PCI: Fixing up bus 0 Time: MIPS clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered gpio_init 156 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher fuse init (API version 7.8) io scheduler noop registered (default) Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A loop: module loaded PPP generic driver version 2.4.2 PPP MPPE Compression module registered NET: Registered protocol family 24 pflash: found no supported devices sflash: squash filesystem with lzma found at block 1786 Creating 4 MTD partitions on "sflash": 0x00000000-0x00030000 : "boot" 0x00030000-0x007f0000 : "linux" 0x001be828-0x007f0000 : "rootfs" 0x007f0000-0x00800000 : "nvram" usbmon: debugfs is not available GACT probability on Mirror/redirect action on u32 classifier input device check on Actions configured Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (512 buckets, 4096 max) ctnetlink v0.93: registering with nfnetlink. BCM fast NAT: INIT ip_tables: (C) 2000-2006 Netfilter Core Team ClusterIP Version 0.8 loaded successfully arp_tables: (C) 2002 David S. Miller TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Ebtables v2.0 registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 176k freed Warning: unable to open an initial console. Failed to execute /init |
cpu info |
---|
# cat /proc/cpuinfo system type : Broadcom BCM5357 chip rev 2 processor : 0 cpu model : MIPS 74K V4.9 BogoMIPS : 264.60 wait instruction : no microsecond timers : yes tlb_entries : 64 extra interrupt vector : no hardware watchpoint : yes ASEs implemented : mips16 dsp VCED exceptions : not available VCEI exceptions : not available unaligned_instructions : 19 dcache hits : 2147483648 dcache misses : 3578002286 icache hits : 2147483648 icache misses : 2836364265 instructions : 2147483648 |
Partitions |
---|
# cat /proc/mtd dev: size erasesize name mtd0: 00030000 00010000 "boot" mtd1: 007c0000 00010000 "linux" mtd2: 006317d8 00010000 "rootfs" mtd3: 00010000 00010000 "nvram" |
lsmod |
---|
# lsmod Module Size Used by Tainted: P pppol2tp 33456 0 act_connmark 2944 4 ohci_hcd 26384 0 wl_high 1148144 0 ehci_hcd 46496 0 usb_storage 45296 0 wl 1780800 0 et 59328 0 |
netstat |
---|
# netstat -l Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN tcp 0 0 192.168.168.1:1780 0.0.0.0:* LISTEN tcp 0 0 192.168.169.1:1780 0.0.0.0:* LISTEN tcp 0 0 fonera.fon:1780 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:3989 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:53 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:3990 0.0.0.0:* LISTEN netstat: no support for 'AF INET6 (tcp)' on this system udp 0 0 localhost.localdomain:38032 0.0.0.0:* udp 0 0 localhost.localdomain:1817 0.0.0.0:* udp 0 0 localhost.localdomain:40100 0.0.0.0:* udp 0 0 localhost.localdomain:40101 0.0.0.0:* udp 0 0 localhost.localdomain:40102 0.0.0.0:* udp 0 0 0.0.0.0:53 0.0.0.0:* udp 0 0 0.0.0.0:67 0.0.0.0:* udp 0 0 0.0.0.0:67 0.0.0.0:* udp 0 0 0.0.0.0:67 0.0.0.0:* udp 0 0 0.0.0.0:39000 0.0.0.0:* udp 0 0 0.0.0.0:1900 0.0.0.0:* udp 0 0 0.0.0.0:38000 0.0.0.0:* netstat: no support for 'AF INET6 (udp)' on this system raw 0 0 0.0.0.0:2 0.0.0.0:* 7 raw 0 0 0.0.0.0:255 0.0.0.0:* 7 netstat: no support for 'AF INET6 (raw)' on this system Active UNIX domain sockets (only servers) Proto RefCnt Flags Type State I-Node Path |
wl revinfo |
---|
# wl -i eth1 revinfo vendorid 0x14e4 deviceid 0x4329 radiorev 0x52057000 chipnum 0x5357 chiprev 0x2 chippackage 0x8 corerev 0x1c boardid 0x550 boardvendor 0x14e4 boardrev P200 driverrev 0x5463722 ucoderev 0x256013e bus 0x0 phytype 0x4 phyrev 0x9 anarev 0x0 # wl -i eth1 revinfo vendorid 0x14e4 deviceid 0x4329 radiorev 0x52057000 chipnum 0x5357 chiprev 0x2 chippackage 0x8 corerev 0x1c boardid 0x550 boardvendor 0x14e4 boardrev P200 driverrev 0x5463722 ucoderev 0x256013e bus 0x0 phytype 0x4 phyrev 0x9 anarev 0x0 |
Categories:
- Fon Wireless
- Embedded system/wireless router
- Embedded System Broadcom
- Embedded System BCM5358UB0
- Broadcom
- Embedded System MIPS 74K
- Embedded System
- Manuf Arcadyan
- Has Mimo Status
- Embedded System IEEE 802.11b/g/n
- Embedded System BCM43236B
- Embedded System IEEE 802.11a/n
- Dual-Radio Wireless Embedded System
- Wireless Embedded System
- Dual-Band
- English Documentation