Fortinet FortiGate-51E (FG-51E)
| Secure SD-WAN Next Generation Firewall | |||||||||||||||||||||||||
|
| |||||||||||||||||||||||||
| WikiDevi.wi-cat.ru | Fortinet FortiGate-51E (FG-51E) | ||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 3rd Party Firmware | |||||||||||||||||||||||||
| dd-wrt | Status Unknown | ||||||||||||||||||||||||
| OpenWrt | Supported | ||||||||||||||||||||||||
| Tomato any flavor | Incompatible | ||||||||||||||||||||||||
| Gargoyle | Status Unknown | ||||||||||||||||||||||||
| Platform | |||||||||||||||||||||||||
| Brand • Model • Rev | Fortinet FortiGate-51E (FG-51E) | ||||||||||||||||||||||||
| Board ID | 19K-W13-6900R | ||||||||||||||||||||||||
| Type | SD-WAN Router | ||||||||||||||||||||||||
| CPU1 | Marvell 88F6820 | ||||||||||||||||||||||||
| CPU1 Type | ARMv7 Cortex-A9 | ||||||||||||||||||||||||
| CPU1 Speed | 1.6 GHz ( 2 cores ) | ||||||||||||||||||||||||
| Flash1 Chip | Macronix MX66L1G45GMI-10G | ||||||||||||||||||||||||
| Flash1 Size | 128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (SPI (NOR)) | ||||||||||||||||||||||||
| RAM1 Size | 2 GiB 2,048 MiB <br />2,147,483,648 B <br />16,777,216 Kib <br />2,097,152 KiB <br />16,384 Mib <br /> (DDR3 SDRAM) | ||||||||||||||||||||||||
| RAM1 Chip | Micron MT41K512M8DA-107:P x 4 | ||||||||||||||||||||||||
| ETH chip1 | Marvell 88F6820 | ||||||||||||||||||||||||
| ETH chip2 | Marvell 88E1512 | ||||||||||||||||||||||||
| ETH chip3 | Marvell 88E1512 | ||||||||||||||||||||||||
| Switch | Marvell 88E6176 | ||||||||||||||||||||||||
| Ethernet Port Count |
2-1GbE-WAN 5-1GbE-LAN | ||||||||||||||||||||||||
| Wired Standard | IEEE 802.3i/3u/3ab | ||||||||||||||||||||||||
| Jumbo frame | 70:4C:A5"70:4C:A5" is not in the list (yes, no, unspecified) of allowed values for the "LAN Jumbo Frame support" property. | ||||||||||||||||||||||||
| Stock bootloader | U-Boot | ||||||||||||||||||||||||
| Expansion IF types | USB 3.0, mSATA | ||||||||||||||||||||||||
| USB ports | 1 | ||||||||||||||||||||||||
| SATA Ports | 1 | ||||||||||||||||||||||||
| USB Hub Compatible | Untested | ||||||||||||||||||||||||
| Power | 12 VDC, 2 A | ||||||||||||||||||||||||
| Connector type | Molex (2-pin) | ||||||||||||||||||||||||
| Serial Port (UART) | yes, RJ-45 console, (9600 8N1) | ||||||||||||||||||||||||
|
Flags: | |||||||||||||||||||||||||
|
Additional chips | |||||||||||||||||||||||||
| Other | |||||||||||||||||||||||||
|
Default IP address: 192.168.1.99 | |||||||||||||||||||||||||
| Manuf/OEM/ODM | Gemtek WRTM-320N V02 | ||||||||||||||||||||||||
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) | ||||||||||||||||||||||||
| Retail | |||||||||||||||||||||||||
| Availability | End of Life | ||||||||||||||||||||||||
| (Est.) release date | February 2016 | ||||||||||||||||||||||||
| ASIN |
B07TK3M4BF | ||||||||||||||||||||||||
| Country of manuf | China | ||||||||||||||||||||||||
| |||||||||||||||||||||||||
For a list of all currently documented Marvell chipsets with specifications, see Marvell.
For a list of all currently documented Fortinet devices with specifications, see Fortinet.
Overview
"Model: P17457-03", "FG-51E", "Fortinet, Inc", "19K-W13-6900R RoHs",
- and "WRTM-320N_V02" are silkscreened on board.
OEM: Gemtek WRTM-320N (V02)
Hardware specification
- CPU: Marvell 88F6820 Armada 385
- Dual-Core ARM (Cortex-A9) @1.6GHz
- Storage: 128MB SPI (NOR) Flash,
- 32GB mSATA SSD
- Memory: 2GB (DDR3) SDRAM
- Network: 7x GbE ports
- USB: 1x USB 3.0 port
- Power Source: 12V/3A via 2-pin Molex
Links of Interest
Flashing
| NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
Subtarget: cortexa9
Package architecture: arm_cortex-a9_vfpv3-d16
Supported Since Commit
Support started version: 24.10.0
Current supported version: 24.10.5
WLAN Comment: No WLAN
Install Comment:
see git-commit
Recovery method(s):
See commit for instructions
Recovery Comment:
see git-commit
| git • >> |
|---|
mvebu: add support for Fortinet FortiGate 51E
Fortinet FortiGate 51E (FG-51E) is a UTM, based on Armada 385 (88F6820).
Specification:
- SoC : Marvell Armada 385 88F6820
- RAM : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ")
- Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- SSD : mSATA SSD 32 GB (A-DATA XM21E (AXM21ES3-32GM-B))
- mode : SATA III 6Gbps
- power : 3.3 VDC, 3.1 W (Max.)
- Ethernet : 7x 10/100/1000 Mbps
- LAN 1-5 : Marvell 88E6176
- WAN 1, 2 : Marvell 88E1512 (2x)
- LEDs/Keys : 18x/1x
- UART : "CONSOLE" port (RJ-45, RS-232C level)
- port : ttyS0
- settings : 9600bps 8n1
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- note : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power : 12 VDC, 2.5 A
- plug : Molex 5557-02R
Flash instruction using initramfs image:
1. Power on FG-51E and interrupt to show bootmenu
2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
and set baudrate to 9600 bps
3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
connect computer to "Image download port" in the parameters
4. Prepare TFTP server with the parameters obtained above
5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
directory
6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
image from TFTP server
7. Type "R" key when the following message is showed, to boot initramfs
image without flashing to spi-nor flash
"Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"
8. On initramfs image, backup mtd if needed
minimum:
- "firmware-info"
- "kernel"
- "rootfs"
9. On initramfs image, upload sysupgrade image to the device and perform
sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
If the device is booted with stock firmware, login to bootmenu and
call "[B]: Boot with backup firmware and set as default." to set the
first OS image as default and boot it.
Notes:
- Both colors of Bi-color LEDs on the front panel cannot be turned on at
the same time.
- "PWR" and "Logo" LEDs are connected to power source directly.
- The following partitions are added for OpenWrt.
These partitions are contained in "uboot" partition (0x0-0x1fffff) on
stock firmware.
- "firmware-info"
- "dtb"
- "u-boot-env"
- "board-info"
Image header for bootmenu tftp:
0x0 - 0xf : ?
0x10 - 0x2f : Image Name
0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?
*: required for initramfs image
MAC addresses:
(eth0): 70:4C:A5:xx:xx:98 (board-info (OpenWrt), 0xd880 (hex))
WAN 1 : 70:4C:A5:xx:xx:99
WAN 2 : 70:4C:A5:xx:xx:9A
LAN 1 : 70:4C:A5:xx:xx:9B
LAN 2 : 70:4C:A5:xx:xx:9C
LAN 3 : 70:4C:A5:xx:xx:9D
LAN 4 : 70:4C:A5:xx:xx:9E
LAN 5 : 70:4C:A5:xx:xx:9F
|