GL.iNet GL-S1300 (Convexa-S)

multiple revisions of this device, use caution

abgn+ac (AC1300)
CONVEXA-S OpenWrt Gateway for Smart Home Wireless Devices
Homepage	Product page
WikiDevi.wi-cat.ru	GL.iNet GL-S1300
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	GL.iNet GL-S1300 (Convexa-S)
FCC ID	2AFIW-S1300
Type	wireless system, IoT hub
CPU1 Y	Qualcomm IPQ4029
CPU1 Type	ARMv7 Cortex-A7
CPU1 Speed	716 MHz ( 4 cores )
CPU2 ?	Silicon Labs EFR32MG
Flash1 Chip	Brand? Model?
Flash1 Size	16 MiB 16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> (SPI NOR)
Flash2 Chip	SK hynix H26M41204HPR
Flash2 Size	8 GiB 8,192 MiB <br />8,589,934,592 B <br />67,108,864 Kib <br />8,388,608 KiB <br />65,536 Mib <br /> (eMMC)
RAM1 Size	512 MiB 536,870,912 B <br />4,194,304 Kib <br />524,288 KiB <br />4,096 Mib <br />0.5 GiB <br />
RAM1 Chip	Micron MT41K256M16HA-125:E
ETH chip1	Qualcomm IPQ4029
Switch	Qualcomm Atheros QCA8075
Ethernet Port Count	1-1GbE-WAN 2-1GbE-LAN
Wired Standard	IEEE 802.3i/3u/3ab
802dot11 OUI: E4:95:6E (5 E, 6 W) Ethernet OUI: E4:95:6E (5 E, 6 W)
Expansion IF types	USB 3.0
USB ports	1
USB Hub Compatible	Untested
Power	12 VDC, 1.5 A
Connector type	barrel
Flags: Wave2, 256QAM, MU-MIMO, SON, Bluetooth 5.1 LE, ZigBee
Other
Default SSID: GL-S1300-XXX (1 addl. devices) Default IP address: 192.168.8.1 the IP 192.168.8.1 is used by 44 additional devices of which 23 are GL.iNet devices
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Retail
FCC approval date	30 April 2019
Country of manuf	China
Radio 1
Chip1	Qualcomm IPQ4029
Wireless interface OUI	E4:95:6E
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11b/g/n
n-QAM	up to 400 Mbps
802.11n	up to 300 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
Radio 2
Chip1	Qualcomm IPQ4029
Wireless interface OUI	E4:95:6E
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11a/n/ac
802.11ac	up to 867 Mbps
802.11n	up to 300 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz
FCC ID GL.iNet GL-S1300F16 2AFIW-S1300
CPU1 brand Radio1 chip1 brand Radio2 chip1 brand GL.iNet GL-S1300 (Convexa-S) Qualcomm Qualcomm Qualcomm GL.iNet GL-S1300F16 Qualcomm Qualcomm Qualcomm

For a list of all currently documented Qualcomm chipsets with specifications, see Qualcomm.
For a list of all currently documented Qualcomm Atheros (QCA) chipsets with specifications, see Qualcomm Atheros.
For a list of all currently documented Silicon Labs chipsets with specifications, see Silicon Labs.

For a list of all currently documented GL.iNet devices with specifications, see GL.iNet.

• 400 Mbps - 2SS 2.4GHz 802.11n (40MHz chan., 256-QAM),

• 867 Mbps - 2SS 5GHz 802.11ac (80MHz chan.) = AC1300 class

Overview

"GL-S1300_V1.2.2" is silkscreened on the board in the FCC photos.

"D9PXV" Micron FBGA code on the RAM corresponds to the MT41K256M16HA-125:E

Official Store

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)
On the OpenWrt Wiki

Target: ipq40xx
Subtarget: generic
Package architecture: arm_cortex-a7_neon-vfpv4
Supported Since Commit
Support started version: 21.02.0
Current supported version: 25.12.1

LAN Hardware: Qualcomm Atheros QCA8075
WLAN Hardware: Qualcomm Atheros IPQ4029
Installation method(s):
see git-commit
Comment:
Also known as Convexa-S. Supports an internal Zigbee or Bluetooth module. Missing DSA Setup since 23.05+

git • >>

ipq40xx: add support for GL.iNet GL-S1300 Specifications: SOC: Qualcomm IPQ4029 (DAKOTA) ARM Quad-Core RAM: 512 MiB FLASH1: 16 MiB NOR - SPI0 FLASH2: 8 GiB eMMC ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4029 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4029 5GHz 802.11n/ac W2 2x2 INPUT: Reset, WPS LED: Power, Mesh, WLAN UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 UART2: On board with BLE module SPI1: On board socket for Zigbee module Install via tftp - NB: need to flash transition image firstly Firstly install transition image: (IPQ40xx) # tftpboot 0x84000000 s1300-factory-to-openwrt.img (IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script Secondly install openwrt sysupgrade bin: (IPQ40xx) # run lf Revert to factory image: (IPQ40xx) # tftpboot 0x84000000 s1300-openwrt-to-factory.img (IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script The kernel and rootfs of factory firmware are on eMMC, and openwrt firmware is on NOR flash. The transition image includes U-boot and partition table, which decides where to load kernel and rootfs. After you firstly install openwrt image, you can switch between factory and openwrt firmware by flashing transition image.

Pictures

Retail Images

• 
• 
• 
• 

See also

Models

GL.iNet • Products • Compare • FCC ID - 2AFIW

GL.iNet GL-BE14000 (Flint 4) GL.iNet GL-BE9300 (Flint 3) GL.iNet GL-BE6500 (Flint 3e) GL.iNet GL-BE3600 (Slate 7) GL.iNet GL-MT3600BE (Beryl 7) GL.iNet GL-MT3000 (Beryl AX) GL.iNet GL-MT1300 (Beryl) GL.iNet GL-AX1800 (Flint) GL.iNet GL-AXT1800 (Slate AX) GL.iNet GL-XE3000 (Puli AX) GL.iNet GL-XE300 (Puli) GL.iNet GL-X3000 (Spitz AX) GL.iNet GL-X1200 (Amarok) GL.iNet GL-X300B (Collie) GL.iNet GL-B3000 (Marble) GL.iNet GL-B2200 (Velica) GL.iNet GL-B1300 (Convexa-B) GL.iNet GL-A1300 (Slate Plus) GL.iNet GL-AP1300-LTE (Cirrus) GL.iNet GL-S1300-F16 (Convexa-S) GL.iNet GL-SF1200 (Meet) GL.iNet GL-SFT1200 (Opal)

GL.iNet GL-MT6000 (Flint 2) GL.iNet GL-MT5000 (Brume 3) GL.iNet GL-MT2500A (Brume 2) GL.iNet GL-MV1000W (Brume-W) GL.iNet GL-MV1000 (Brume) GL.iNet GL-MT300A (Azure) GL.iNet GL-MT300N (Mango) GL.iNet GL-MT300N-V2 (Mango 2) GL.iNet GL-AR750S-Ext (Slate) GL.iNet GL-AR750-PoE (Creta) GL.iNet GL-E750-V2 (Mudi) GL.iNet GL-X750-V2 (Spitz) GL.iNet GL-MT750 (Moon) GL.iNet GL-AR300 (Black) GL.iNet GL-AR300M (Shadow) GL.iNet GL-AR150 (White) GL.iNet GL-USB150 (Microuter) GL.iNet Microuter-N300 • GL-MiFi GL.iNet GL-S10 • S20 • S200 GL.iNet GL-RM1 (Comet) GL.iNet GL-RM10 (Comet Pro) GL.iNet 6416A (6408A)