GL.iNet GL-S200

bgn (N150)
wireless router
Homepage	Product page
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	GL.iNet GL-S200
FCC ID	none specified
Type	wireless router
CPU1 Y	Qualcomm Atheros QCA9531
CPU1 Type	MIPS 24Kc
CPU1 Speed	650 MHz
Flash1 Chip	Brand? Model?
Flash1 Size	128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (SPI NAND)
Flash2 Size	16 MiB16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> (SPI NOR)
RAM1 Size	128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (DDR2)
RAM1 Chip	Brand? Model?
ETH chip1	Qualcomm Atheros QCA9531
Switch	Qualcomm Atheros QCA9531
Ethernet Port Count	1-100MbE-WAN 2-100MbE-LAN
Wired Standard	IEEE 802.3i/3u
802dot11 OUI: none specified
Stock bootloader	U-Boot
Stock FW OS	Linux OpenWrt
Expansion IF types	none specified
Power	5 VDC, 2 A
Connector type	USB (Type-C)
Other
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Radio 1
Chip1	Qualcomm Atheros QCA9531
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	1x1:1
Wireless Standard	IEEE 802.11b/g/n
802.11n	up to 150 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz

For a list of all currently documented Qualcomm Atheros (QCA) chipsets with specifications, see Qualcomm Atheros.

For a list of all currently documented GL.iNet devices with specifications, see GL.iNet.

• 150 Mbps - 1SS 2.4GHz 802.11n (40MHz chan.) = N150 class

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)

Target: ath79
Subtarget: nand
Package architecture: mips_24kc
Supported Since Commit
Support started version: 24.10.0
Current supported version: 25.12.0

WLAN Hardware: Qualcomm Atheros QCA9531
WLAN Comment: Thread + ZigBee/Zwave
Installation method(s):
see git-commit
Recovery method(s):
see git-commit

git • >>

ath79: add support for GL.iNet GL-S200 Specifications: SoC: QCA9531(650MHz) RAM: DDR2 128M Flash: SPI NOR 16M + SPI NAND 128M WiFi: 2.4GHz with 2 antennas(WiFi/Thread) Ethernet: 1xLAN(10/100M) 2xWAN(10/100M) Button: 1x Reset Button Switch: 1x Mode switch LED: 1x Blue LED + 1x White LED + 1x Orange LED IOT: Thread + ZigBee/Zwave By uboot web failsafe: Push the reset button for 5 seconds util the power led flash faster, then use broswer to access http://192.168.1.1 Afterwards upgrade can use sysupgrade image.