Handlink AP-100
From TechInfoDepot
Jump to navigationJump to searchbgn (N300) | |||||
|---|---|---|---|---|---|
| AP-100 Smart Wi-Fi Access Point | |||||
| Homepage | |||||
| 3rd Party Firmware | |||||
| dd-wrt |
Status Unknown | ||||
| OpenWrt |
Status Unknown | ||||
| Tomato any flavor |
Incompatible | ||||
| Platform | |||||
| Brand • Model • Rev |
Handlink AP-100 | ||||
| FCC ID | |||||
| Type |
access point, CPE | ||||
| CPU1 | |||||
| CPU1 Type |
MIPS 74Kc | ||||
| CPU1 Speed |
560 MHz 32-bit | ||||
| Flash1 Chip |
Macronix MX25L6406EMI-12G | ||||
| Flash1 Size |
8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> | ||||
| RAM1 Size |
32 MiB33,554,432 B <br />262,144 Kib <br />32,768 KiB <br />256 Mib <br />0.0313 GiB <br /> | ||||
| RAM1 Chip |
EtronTech EM68A16CWQB-25H | ||||
| ETH chip1 | |||||
| Ethernet Port Count |
1-100MbE-LAN | ||||
| Wired Standard |
IEEE 802.3i/3u | ||||
|
802dot11 OUI: none specified | |||||
| Expansion IF types |
none specified | ||||
| PoE |
non-standard (otherwise unspecified) | ||||
| Power |
18 VDC, 0.66 A | ||||
| Connector type |
Ethernet (PoE) | ||||
|
Flags: hg directional | |||||
| Other | |||||
|
Default SSID: Superwifi Network X | |||||
| Manuf/OEM/ODM | |||||
| Retail | |||||
| FCC approval date | 17 October 2013 | ||||
| Country of manuf | Taiwan | ||||
| Radio 1 | |||||
| Chip1 | |||||
| Wireless interface OUI |
none specified | ||||
| Antenna Connector Type |
none specified | ||||
| MIMO status |
2x2:2 | ||||
| Wireless Standard |
IEEE 802.11b/g/n | ||||
| 802.11n |
up to 300 Mbps | ||||
| 802.11g |
up to 54 Mbps | ||||
| 802.11b |
up to 11 Mbps | ||||
| WiFi Operating Frequency |
2.4 GHz | ||||
| |||||
For a list of all currently documented Atheros (QCA) chipsets with specifications, see Atheros.
- • 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.) = N300 class
Overview
"M01-"????"-X01" appears to be silkscreened on the board in the FCC photos.
CPU: Atheros AR9344-BC2A
RAM: EtronTech EM68A16CWQB-25H / Winbond W9725G6JB-25
This device is using two Skyworks ( / SiGe) SE2576L / 2576L 2.4GHz Power Amplifier modules.
The hardware of this device would appear to be the same (or very similar to) that of the Altai C1n Super WiFi CPE/AP.
Default settings are per the FCC manual.
- The default SSID format is stated to be Superwifi Network + a space + a number between 0 and 7.
- A 00:19:BE (Altai) OUI is shown as being used within the manual..
