Huasifei WH3000 Pro

multiple revisions of this device, use caution

abgn+ac+ax (AX3000)
Mini Portable 5G CPE
Homepage	Product page
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	Huasifei WH3000 Pro
FCC ID	none specified
Type	travel router
CPU1 Y	MediaTek MT7981A
CPU1 Type	ARM Cortex-A53
CPU1 Speed	1.3 GHz ( 2 cores ) 64-bit
Flash1 Chip	Brand? Model?
Flash1 Size	8 GiB 8,192 MiB <br />8,589,934,592 B <br />67,108,864 Kib <br />8,388,608 KiB <br />65,536 Mib <br /> (eMMC)
RAM1 Size	1 GiB 1,024 MiB <br />1,073,741,824 B <br />8,388,608 Kib <br />1,048,576 KiB <br />8,192 Mib <br /> (DDR4)
RAM1 Chip	Brand? Model?
ETH chip1	MediaTek MT7981A
ETH chip2	MediaTek RTL8221B
Ethernet Port Count	1-2.5GbE-WAN 1-1GbE-LAN
Wired Standard	IEEE 802.3i/3u/3ab/3bz
802dot11 OUI: none specified
Stock bootloader	U-Boot
Expansion IF types	M.2, USB 3.0, Nano SIM
SIM Card slot	1
USB ports	1
M.2 Slots	1
USB Hub Compatible	Untested
Power	5 VDC, 3 A
Connector type	USB (Type-C)
Serial Port (UART)	yes, 3.3V TTL, (115200 8N1)
Flags: Mobile Wireless/Cellular network
Other
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Radio 1
Chip1	MediaTek MT7981A
Chip2	MediaTek MT7976CN
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11b/g/n/ax
802.11ax	up to 574 Mbps
802.11n	up to 300 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
Radio 2
Chip1	MediaTek MT7981A
Chip2	MediaTek MT7976CN
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11a/n/ac/ax
AX-QAM	up to 2402 Mbps
802.11ax	up to 1201 Mbps
802.11ac	up to 867 Mbps
802.11n	up to 300 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz
CPU1 brand Radio1 chip1 brand Radio2 chip1 brand Huasifei WH3000 MediaTek MediaTek MediaTek Huasifei WH3000 Pro MediaTek MediaTek MediaTek

For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.

• 574 Mbps - 2SS 2.4GHz 802.11ax (40MHz chan., 1024QAM),

• 2402 Mbps - 2SS 5GHz 802.11ax (160MHz chan., 1024QAM) = AX3000 class

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)

Target: mediatek
Subtarget: filogic
Package architecture: aarch64_cortex-a53
Supported Since Commit
Support started version: 24.10.3
Current supported version: 24.10.5

LAN Comment: Realtek RTL8221B for 2.5GbE Phy, Qualcomm X62 5G Modem
WLAN Hardware: MediaTek MT7981BA, MediaTek MT7976CN
Installation method(s):
see git-commit
Recovery method(s):
see git-commit

git • >>

mediatek: add Huasifei WH3000 Pro support **Huasifei WH3000 Pro** Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC. MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ with 5G modems module and PWM Fan. **Specifications** SoC: Filogic 820 MT7981A (1.3GHz) RAM: DDR4 1GB Flash: eMMC 8GB WiFi: 2.4GHz and 5GHz with 3 antennas Ethernet: 1x WAN (10/100/1000M) 1x LAN (10/100/1000/2500M) USB: 1x USB 3.0 port Two buttons: power/reset and mode (BTN_0) LEDS: blue, red, blue+red=pink UART: 3.3V, TX, RX, GND / 115200 8N1 **Installation via U-Boot rescue** 1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1 2. Connect to the WAN port and hold the reset button while booting the device. 3. Wait for the LED to blink 5 times, and release the reset button. 4. Open U-boot web page on your browser at http://192.168.1.1 5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade. 6. Wait for the router to flash the new firmware. 7. Wait for the router to reboot itself. **Installation via sysupgrade** Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings. **Installation via SSH** Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command: ``` sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-pro-squashfs-sysupgrade.bin ``` **Factory MAC** You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4` ``` dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C ``` Cherry-picked from https://github.com/coolsnowwolf/lede/commit/949d0bd77a2e97c2d982531f72b76c575fb28839 Fixed `green` to `blue` LED in dts, added `SUPPORTED_DEVICES += huasifei,fudy-pro` - to make sysupgrade compatible with factory QWRT/Lede fork firmware. Signed-off-by: Fil Dunsky Link: https://github.com/openwrt/openwrt/pull/19315 Signed-off-by: Hauke Mehrtens