INexQ (Unex) ISW054t/Serial info

From TechInfoDepot
Jump to navigationJump to search

Info derived from

boot log

Power-On Self Testing...
Testing SYS Controller...
Testing MEM Controller...
SDRAM Configuration:ROW11_COL8_BANK2
Testing SDRAM Memory ...
From 0x80000000 - 0x807FFFFF
Testing CPU Data RAM...
Testing CPU Internal Registers...
Testing Timer 0...
Testing Timer 1...
Testing DMA Controller...
Testing INT Controller...
Testing PCMCIA Controller...
Testing USB Controller...
Testing Ethernet 0 MAC...
Testing Ethernet 1 MAC...
Testing Cardbus...
Testing PCI...
Power-On Self Test Passed

          Bootloader Version 00-03-02, Aug 29 2003 21:45:21

       Copyright 2003. All rights reserved.

Press any key to stop auto-boot...
 0
auto-booting...

========POR reset========

Start of heap: 0x80629f30
End of heap: 0x80800000

Firmware Version: 20-06-07T5, Oct 22 2003 15:46:54
Copyright 2002-2003. All rights reserved.
Scanning PCI Bus...
    scan PCI deviceNo=1
      Found ISL3890 Wireless Device: PCIDEV=1, DEVNUM=4, NICNO=0

WLAN0 Zone Number is 0
******** WLAN Enabled *******
******* AP CONFIG LAUNCHED *******
WLS Channael number is 6
Finished wlan firmware download
Link State: 6c 00 00 00 34 2e
br0: port 0.0.0.1(eth1 rootport) entering listening state
br0: port 0.0.0.2(wls0 rootport) entering listening state
NAT/Firewall starting...
MaxSessionNumber: 65536
NAT/Firewall started!
Now try to get the configuration file...
interface eth1 uses following ip settings: 192.168.62.1/255.255.255.0
Initialization of NAT/Firewall policy database succeeded!
load_pptp_wan: encryption option=e1
br0: port 0.0.0.2(wls0 rootport) entering learning state
br0: port 0.0.0.1(eth1 rootport) entering learning state
br0: port 0.0.0.2(wls0 rootport) entering forwarding state
br0: topology change detected, propagating
br0: port 0.0.0.1(eth1 rootport) entering forwarding state
br0: topology change detected, propagating
SD9218> dhcp_update_table called, iface=1
start_ip=192.168.62.50, end_ip=192.168.62.100
route_cfg_update: dycfg.tx_protocol=0, dycfg.rx_protocol=0, dycfg.mode=0
dhcp_update_table return
bootloader menu + boot params
BOOT> ?
                       Main menu

        ?         - print this menu
        f         - load from Flash and go
        l         - load from TFTP server to SDRAM (no save to Flash, no go)
        L         - load from TFTP server to SDRAM and go (no save to Flash)
        @         - load from TFTP server to SDRAM,save to Flash and go
        g         - go from address
        b         - show boot parameters
        c         - change boot parameters
        d         - display factory default parameters
        m         - modify/set factory default parameters
        p         - ping test (ping other station from the target)
        r         - read memory
        s         - change mac address only
        w         - write memory

BOOT> b

        tftpserver     (R/W)    192.168.62.10
        tftpfile       (R/W)    zrtos.img
        ipaddr         (R/W)    192.168.62.1
        subnetmask     (R/W)    255.255.255.0
        gateway        (R/W)    0.0.0.0