Linksys E5350

abgn+ac (AC10002S)
AC1000 Dual-Band WiFi Router
Wikipedia	Linksys routers
WikiDevi.wi-cat.ru	Linksys E5350
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	Linksys E5350 v1
FCC ID	Q87-03418
IC ID	3839A-03418
Board ID	EWW302-A1-BL-015
Type	wireless router
CPU1 Y	MediaTek MT7628DAN
CPU1 Type	MIPS 24KEc
CPU1 Speed	580 MHz
Flash1 Chip	Winbond W25Q128BV
Flash1 Size	8 MiB 8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br />
RAM1 Size	64 MiB 67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br />
RAM1 Chip	MediaTek MT7628DAN
ETH chip1	MediaTek MT7628DAN
Switch	MediaTek MT7628DAN
Ethernet Port Count	1-100MbE-WAN 4-100MbE-LAN
Wired Standard	IEEE 802.3i/3u
802dot11 OUI: none specified
Stock bootloader	U-Boot
Stock FW OS	Linux 2.6.36
Expansion IF types	none specified
Power	12 VDC, 0.5 A
Connector type	barrel
Serial Port (UART)	yes, 3.3V TTL, (115200 8N1)
Other
Default SSID: LinksysXXXXX (17 addl. devices) Default IP address: 192.168.1.1 the IP 192.168.1.1 is used by 1359 additional devices of which 155 are Linksys devices
Manuf/OEM/ODM	CyberTAN EWW302 -A1
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Retail
FCC approval date	02 February 2019
(Est.) initial retail price (in USD):	$40
ASIN	B07RD8NHS2
Country of manuf	China
Radio 1
Chip1	MediaTek MT7628DAN
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11b/g/n
802.11n	up to 300 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
Radio 2
Chip1	MediaTek MT7612EN
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11a/n/ac
802.11ac	up to 650 Mbps
802.11n	up to 300 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz
FCC ID Linksys E2500 v4 Q87-03418 Linksys E5300 Q87-03418 Linksys E5400 Q87-03418

For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.

For a list of all currently documented Linksys devices with specifications, see Linksys.

• 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.),

• 665 Mbps - 2SS 5GHz 802.11ac (details unknown) = AC1000 class

Overview

"EWW302-A1-BL-015" is silkscreened on the board in the FCC photos.

OEM: CyberTAN EWW302

See also: Linksys E5400 and Wistron NeWeb

• Wi-Fi Certified : WFA81722 (as of 01/25/2019)

This device was under short-term confidentiality, but that expired 08/01/2019 ⚠.

We are guessing that the maximum link rate for 5GHz 802.11ac has been

reduced from 867Mbps to 650Mbps by disabling 256QAM support.

All of the following devices are internally identical:

• Linksys E5400 - AC1200 Dual-Band WiFi Router
• Linksys E5350 - AC1000 Dual-Band WiFi Router
• Linksys E5300 - AC750 Dual-Band WiFi Router
• Linksys E2500 v4 - N600 Dual-Band WiFi Router

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)
On the OpenWrt Wiki

Target: ramips
Subtarget: mt76x8
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 23.05.0
Current supported version: 25.12.2

LAN Hardware: MediaTek MT7628AN
WLAN Hardware: MediaTek MT7628AN, MediaTek MT7612EN
WLAN Comment: MIMO 2x2:2 for each band
Installation method(s):
U-Boot TFTP + serial recovery, see devicepage
Recovery method(s):
U-Boot TFTP + serial recovery

git • >>

ramips: add support for Linksys E5400 and clones Linksys E5400 is a 2.4/5GHz dual band AC router, based on MediaTek MT7628AN. This device is also sold as Linksys E2500v4, E5300 and E5350 with the same hardware, but software speed limitations in vendor firmwares. Specification: * SoC: MT7628AN (580 MHz) * RAM: DDR2 64 MiB * Flash: 16 MiB NOR (W25Q128BV) * Wi-Fi: * 2.4GHz: SoC Built-in * 5GHz: MT7612EN * Ethernet: 5x 100Mbps * Switch: SoC built-in * UART: * 115200, 8N1, 3.3V (real u-boot speed: 119050) * Pinout JB4: 1:[3V3] (TXD) (RXD) [NC] (GND) Flash Layout: 0x0000000-0x0030000 : "Bootloader" 0x0030000-0x0040000 : "Config" 0x0040000-0x0050000 : "Factory" 0x0050000-0x0ff0000 : "Kernel" 0x0ff0000-0x1000000 : "CBTinfo" MAC address: LAN: factory 0x28 WAN: LAN + 1 2.4G: LAN + 2 5G: LAN + 3 Installation: 1. Connect to UART, use LF as EOL (not CRLF) 2. Set IP address - Press 4 during boot - setenv serverip <TFTPSERVER_IP> - setenv ipaddr <DEVICE_IP> - setenv bootfile openwrt-ramips-mt76x8-linksys_e5400-initramfs-kernel.bin - saveenv - reset 3. Load Openwrt Kernel image from TFTP: - Press 1 during boot - IP and filename should be already set 4. Boot into OpenWrt and perform sysupgrade with sysupgrade image.