Linksys WRT3200ACM

From TechInfoDepot
Jump to navigationJump to search
abgn+ac (AC32002R)
AC3200 MU-MIMO Gigabit Wi-Fi Router
Homepage Product page
Support Support page
Wikipedia Linksys routers
WikiDevi.wi-cat.ru Linksys WRT3200ACM
3rd Party Firmware
dd-wrt Supported
OpenWrt Supported
Tomato any flavor Incompatible
Gargoyle Supported
Platform
Brand • Model • Rev Linksys WRT3200ACM v1 (rango)
FCC ID Q87-WRT3200ACM
IC ID 3839A-WRT3200ACM
Board ID 48SAM203.SGD
Type wireless router
Series WRT
CPU1 checkY Marvell 88F6820
CPU1 Type ARMv7 Cortex-A9
CPU1 Speed 1.8 GHz ( 2 cores )
Flash1 Chip Spansion S34ML02G2
Flash1 Size 256 MiB 268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br /> (NAND)
Flash2 Chip Winbond Model? x 2
Flash2 Size 32 MiB33,554,432 B <br />262,144 Kib <br />32,768 KiB <br />256 Mib <br />0.0313 GiB <br /> (Serial(SPI))
RAM1 Size 512 MiB 536,870,912 B <br />4,194,304 Kib <br />524,288 KiB <br />4,096 Mib <br />0.5 GiB <br /> (DDR3)
RAM1 Chip Micron Model? x 2
RAM2 Size 256 MiB268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br /> (DDR3)
RAM2 Chip Micron x 2
ETH chip1 Marvell 88F6820
Switch Marvell 88E6352
Ethernet Port Count 1-1GbE-WAN
4-1GbE-LAN
Wired Standard IEEE 802.3i/3u/3ab
Port-based vlan Yes
802.1q vlan Yes

802dot11 OUI: 60:38:E0 (2 E, 2 W)
Ethernet OUI: 60:38:E0 (2 E, 2 W)

Stock bootloader U-Boot
Stock FW OS Linux 3.10.70
Expansion IF types USB 3.0, USB 2.0 / eSATA (combo port)
USB ports 2
eSATA Ports 1
USB Hub Compatible Untested
Power 12 VDC, 3 A
Connector type barrel
Serial Port (UART) yes, 6-pin header, 3.3V TTL, (115200 8N1)
JTAG Port yes, 20-pad header

Flags:
Wave2, MU-MIMO, VHT160, AP3200, DFS

Additional chips
2.4GHz Front End Module;Skyworks;SKY85309-11;;4;
5GHz Front End Module;Skyworks;SKY85728-11;;4;

Other

Default IP address: 192.168.1.1
the IP 192.168.1.1 is used by 1359 additional devices
of which 155 are Linksys devices

Manuf/OEM/ODM Wistron NeWeb
3rd Party Firmware Support DD-WRT • (List)
, Gargoyle
, LEDE Project (obsolete, OpenWrt) • (List)
, McDebian
, OpenWrt • (List | Dev | DLs)
Retail
Availability End of Life
FCC approval date 21 September 2016
(Est.) release date 18 May 2016
(Est.) initial retail price (in USD): $250
Newegg N82E16833124634
ASINs B01JOXW3YE
B06Y5W188F
Country of manuf China
Radio 1
Chip1 Marvell 88W8964
Wireless interface OUI 60:38:E0
Antenna Connector Type U.FL, RP-SMA
MIMO status 4x4:3
Wireless Standard IEEE 802.11b/g/n
n-QAM up to 600 Mbps
802.11n up to 450 Mbps
802.11g up to 54 Mbps
802.11b up to 11 Mbps
WiFi Operating Frequency 2.4 GHz
Radio 2
Chip1 Marvell 88W8964
Chip2 Marvell 88W8887
Wireless interface OUI 60:38:E0
Antenna Connector Type U.FL, RP-SMA
MIMO status 4x4:3
Wireless Standard IEEE 802.11a/n/ac
AC-QAM up to 2600 Mbps
802.11ac up to 1300 Mbps
802.11n up to 450 Mbps
802.11a up to 54 Mbps
WiFi Operating Frequency 5 GHz
 FCC ID
Linksys WRT32XQ87-WRT3200ACM

For a list of all currently documented Marvell chipsets with specifications, see Marvell.

For a list of all currently documented Linksys devices with specifications, see Linksys.

• 600 Mbps - 3SS 2.4GHz 802.11n (40MHz chan., 256-QAM),
• 2600 Mbps - 3SS 5GHz 802.11ac (80MHz chan., 1024-QAM) = AC3200 class

Overview

"48SAM203.SGD" and "2016.05.18" is silkscreened on the board.

See also: Linksys WRT32X and Wistron NeWeb


This device was under short-term confidentiality, but that expired 01/31/2017 ⚠.

Specifications

  • CPU: Marvell 88F6820-A0 C180 @1.8 GHz (Armada 385)
  • Flash: AMD / Spansion 256MB (NAND), RAM: 512MB (DDR3)
  • WLAN: 2x Marvell 88W8964 4T4R 802.11abgn/ac (MU-MIMO)
1x Marvell 88W8887 1T1R 802.11ac, BT 4.2, NFC, FM rec
Uses a 12V / 3A power adapter

Links of Interest

Wikis

WRT3200ACM - Marvell Armada 385 @1.8GHz (Rango)

Reviews

• CPU: Marvell 88F6820-A0 C180 @1.8GHz (Armada 385 ARMv7)
• 2.4GHz Radio: Marvell 88W8964-BTW2 WiSoC (MU-MIMO)
4x Skyworks SKY85309-11 2.4GHz Front End Module
Micron 128MB DDR3 RAM
• 5GHz Radio: Marvell 88W8964-BTW2 WiSoC (MU-MIMO)
Marvell 88W8887-NAA2 DFS monitor (WLAN/BT/NFC/FM)
4x Skyworks SKY85728-11 5GHz Front End Module
Micron 128MB DDR3 RAM
• Switch: Marvell 88E6352 GbE Switch

Forum threads

Flashing

Flashing dd-wrt

On the DDWRT Wiki
Support started version: wrt3200acm build 30605 20160909
Current supported version: ?

Please insert instructions here

Flashing OpenWrt

Target: mvebu
Subtarget: cortexa9
Package architecture: arm_cortex-a9_vfpv3-d16
Supported Since Commit
Support started version: 17.01.0
Current supported version: 25.12.5
LAN Hardware: Marvell 88E6352
WLAN Hardware: Marvell 88W8964
Installation method(s):
see devicepage
Install Comment:
Image name may need to be changed to OEM Code Name
Recovery method(s):
see devicepage
Recovery Comment:
Image name MUST be OEM Code Name
Comment:
eSATA <-> USB2, [Launch Date: 2016.10] OEM Firmware Name: rango.img
git • >> 
mvebu: add support for the Linksys WRT3200ACM (Rango)
Known issues/workarounds
  • Slower boot times can be observed on 25.12, more information can be found on the [thread for workarounds]. The issue is related to the third radio driver, you can blacklist the modules and remove the module and kmod-mwifiex-sdio package to avoid this, given the third radio is generally not used with OpenWrt and known to have various issues which are well documented.
  • Firmware builds for the 22.03 series beyond 22.03.2 do not exist due to a bug see broken MV88E6176 switch. Builds are available as normal for 23.05 release branch and newer releases.
  • WPA3 support will not reliably work due to mwlwifi driver issues. In certain circumstances it can crash the router completely. **Don't enable it**, use WPA2 only. The mwlwifi driver is unlikely to ever support WPA3.
  • Do not enable 802.11w Management Frame Protection, mwlwifi does not support it properly. It is disabled by default.
  • It is strongly recommended to use auto or channel 36 on radio0 (5.0 GHz) to avoid crashing the WiFi chipset. [discussion]
  • For 21.02 or older builds disabling ASMDU is recommended to avoid latency and issues, this is not required on 22.03.5 or newer versions.
  • If you have multiple SSIDs on a single radio, you may encounter issues with the radio not being able to start. To fix this remove any macaddr configuration from /etc/config/wireless [discussion]
  • Certain embedded devices don't work with the 2.4 GHz radio unless LDPC is disabled. [issue]
  • It has been reported that the 5GHz radio crashes periodically if the irqbalance daemon is installed and enabled.
  • It is suggested to enable packet steering to work around hardware scheduling[1][2] issues.
  • Some time around November 2017, Linksys silently updated the hardware for the WRT3200ACM, but did not change any version numbers or other identifiable labels. In particular, they changed the flash memory chip, which resulted in older firmwares causing bootloops on these new devices. This has since been fixed.
  • You may find additional/supplementary information at the wrt_ac_series page


In the event your wireless configuration is not working or becomes unstable, resetting to defaults is recommend:

uci set wireless.radio0.channel='auto' uci set wireless.radio1.channel='auto' uci set wireless.radio2.channel='auto' uci del wireless.default_radio0.macaddr uci del wireless.default_radio1.macaddr uci commit wireless reboot

JTAG-Serial Info

Serial

Serial info
Boot log >> • 
BootROM - 1.73
Booting from NAND flash

General initialization - Version: 1.0.0
AVS selection from EFUSE disabled (Skip reading EFUSE values)
mvSysEnvIsFlavourReduced: TWSI Read of 'flavor' failed
Detected Device ID 6820
High speed PHY - Version: 2.0

Init RD NAS topology Serdes Lane 3 is USB3
Serdes Lane 4 is SGMII
board SerDes lanes topology details:
| Lane # | Speed|    Type     |
------------------------------|
|   0    |  6   |  SATA0      |
|   1    |  5   |  PCIe0      |
|   2    |  6   |  SATA1      |
|   3    |  5   |  USB3 HOST1 |
|   4    |  5   |  PCIe1      |
|   5    |  0   |  SGMII2     |
-------------------------------
:** Link is Gen1, check the EP capability
PCIe, Idx 0: Link upgraded to Gen2 based on client cpabilities
:** Link is Gen1, check the EP capability
PCIe, Idx 1: remains Gen1
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.46.0
mvSysEnvGetTopologyUpdateInfo: TWSI Read failed
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
Not detected suspend to RAM indication
BootROM: Image checksum verification PASSED
__   __                      _ _
|  \/  | __ _ _ ____   _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| |  | | (_| | |   \ V /  __/ | |
|_|  |_|\__,_|_|    \_/ \___|_|_|
         _   _     ____              _
        | | | |   | __ )  ___   ___ | |_
        | | | |___|  _ \ / _ \ / _ \| __|
        | |_| |___| |_) | (_) | (_) | |_
         \___/    |____/ \___/ \___/ \__|

** LOADER **
U-Boot 2013.01 (Apr 08 2016 - 15:47:50) Marvell version: 2015_T1.QA.0p16
Boot version : v0.0.4

Board: RD-NAS-88F6820-DDR3
SoC:   MV88F6820 Rev A0
       running 2 CPUs
CPU:   ARM Cortex A9 MPCore (Rev 1) LE
       CPU 0
       CPU    @ 1866 [MHz]
       L2     @ 933 [MHz]
       TClock @ 200 [MHz]
       DDR3    @ 933 [MHz]
       DDR3 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM:  512 MiB
NAND:  256 MiB
MMC:   mv_sdh: 0
DEVINFO offset == 0x7e0000
U-ENV offset == 0x200000
U-ENV offset == 0x200000
S-ENV offset == 0x220000

#### auto_recovery ####
[u_env] get auto_recovery == yes
[u_env] get auto_recovery == yes
[u_env] get boot_part == 1
[u_env] get boot_part_ready == 3
auto_recovery enabled:1, boot_part:1, boot_part_ready:3

S-ENV offset == 0x220000
[boot_count_read] block:0x220000, size:128KB, records:64
[boot_count_read_record] boot_count:2, next_record:9
[boot_count_write] erase:0, auto_recovery->
block_offset:0x220000 offset=0x224800

Updating boot_count ...
[boot_count_write] offset:0x224800 , length:2048
done

PCI-e 0 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 2.0
PCI-e 1 (IF 1 - bus 1) Root Complex Interface, Detected Link X1, GEN 1.1
USB2.0 0: Host Mode
USB3.0 1: Host Mode
USB3.0 0: Host Mode

Map:   Code:                    0x1feab000:0x1ff75a20
       BSS:                     0x1ffef164
       Stack:                   0x1f9aaf20
       Heap:                    0x1f9ab000:0x1feab000
U-ENV offset == 0x200000
U-ENV offset == 0x200000
       U-Boot Environment:      0x00200000:0x00220000 (NAND)

Board configuration detected:
mvEthE6171SwitchBasicInit init
Net:
|  port  | Interface | PHY address  |
|--------|-----------|--------------|
| egiga0 |   RGMII   |     0x01     |
| egiga1 |   SGMII   |     0x00     |
| egiga2 |   SGMII   |   In-Band    |
egiga0 [PRIME], egiga1, egiga2
auto_recovery_check changes bootcmd: run nandboot
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0xa00000, size 0x600000
6291456 bytes read: OK
## Booting kernel from Legacy Image at 02000000 ...
   Image Name:   Linksys WRT3200 Router
   Created:      2016-08-26   0:55:45 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4659771 Bytes = 4.4 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 3.10.70 (root@build-vm) (gcc version 4.6.4 (Linaro GCC 
branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALIGN) )
 #1 SMP Thu Aug 25 17:55:29 PDT 2016
CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Marvell Armada 380/381/382/383/384/385/388 (Device Tree), 
model: Marvell Armada 385 Development Board
bootconsole [earlycon0] enabled
Memory policy: ECC disabled, Data cache writealloc
PERCPU: Embedded 7 pages/cpu @c1162000 s7488 r8192 d12992 u32768
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock6 ro rootdelay=1 
rootfstype=jffs2 earlyprintk mtdparts=armada-nand:2048K(uboot)ro,128K(u_env),
256K(s_env),256K@8064K(devinfo),1920K@8320K(sysdiag),80m@10m(kernel),74m@16m
(rootfs),80m@90m(alt_kernel),74m@96m(alt_rootfs),160m@10m(ubifs),-@170m(syscfg)
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
allocated 1048576 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
Memory: 512MB = 512MB total
Memory: 508716k/508716k available, 15572k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xe0800000 - 0xfff00000   ( 503 MB)
    lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc084ccd4   (8468 kB)
      .init : 0xc084d000 - 0xc088ed40   ( 264 kB)
      .data : 0xc0890000 - 0xc08e4260   ( 337 kB)
       .bss : 0xc08e4260 - 0xc09ab18c   ( 796 kB)
Hierarchical RCU implementation.
        RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
NR_IRQS:16 nr_irqs:16 16
  LSP version: linux-3.10.70-2015_T1.1p7

sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms
L310 cache controller enabled
l2x0: 16 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x16070000, Cache size: 1048576 B
Console: colour dummy device 80x30
Calibrating delay loop... 3726.54 BogoMIPS (lpj=18632704)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
Initializing cgroup subsys memory
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Calibrating local timer... 933.29MHz.
Setting up static identity map for 0xc064cc58 - 0xc064ccb0
mvebu-pmsu: Initializing Power Management Service Unit
Initializing CPU Reset module
CPU1: Booted secondary processor
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
Brought up 2 CPUs
SMP: Total of 2 processors activated (7453.08 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
mvebu-soc-id: MVEBU SoC ID=0x6820, Rev=0x4
xor: measuring software checksum speed
   arm4regs  :  3309.200 MB/sec
   8regs     :  2234.400 MB/sec
   32regs    :  1905.600 MB/sec
xor: using function: arm4regs (3309.200 MB/sec)
pinctrl core: initialized pinctrl subsystem
regulator-dummy: no parameters
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
irq: Cannot allocate irq_descs @ IRQ195, assuming pre-allocated
irq: Cannot allocate irq_descs @ IRQ227, assuming pre-allocated
bio: create slab <bio-0> at 0
raid6: int32x1    232 MB/s
raid6: int32x2    344 MB/s
raid6: int32x4    437 MB/s
raid6: int32x8    444 MB/s
raid6: using algorithm int32x8 (444 MB/s)
raid6: using intx1 recovery algorithm
mvebu-pcie pcie-controller.6: PCIe0.0: link up
mvebu-pcie pcie-controller.6: PCIe1.0: link up
mvebu-pcie pcie-controller.6: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io  0x1000-0xfffff]
pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
pci_bus 0000:00: root bus resource [bus 00-ff]
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
PCI: bus1: Fast back to back transfers disabled
PCI: bus2: Fast back to back transfers disabled
pci 0000:00:01.0: BAR 8: assigned [mem 0xe0000000-0xe02fffff]
pci 0000:00:02.0: BAR 8: assigned [mem 0xe0400000-0xe06fffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe01fffff 64bit pref]
pci 0000:01:00.0: BAR 2: assigned [mem 0xe0200000-0xe02fffff 64bit pref]
pci 0000:00:01.0: PCI bridge to [bus 01]
pci 0000:00:01.0:   bridge window [mem 0xe0000000-0xe02fffff]
pci 0000:02:00.0: BAR 0: assigned [mem 0xe0400000-0xe05fffff 64bit pref]
pci 0000:02:00.0: BAR 2: assigned [mem 0xe0600000-0xe06fffff 64bit pref]
pci 0000:00:02.0: PCI bridge to [bus 02]
pci 0000:00:02.0:   bridge window [mem 0xe0400000-0xe06fffff]
PCI: enabling device 0000:00:01.0 (0140 -> 0143)
PCI: enabling device 0000:00:02.0 (0140 -> 0143)
vgaarb: loaded

SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 
- Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
Switching to clocksource armada_370_xp_clocksource
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
fuse init (API version 7.22)
msgmni has been set to 993
async_tx: api initialized (async)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
mv_xor f1060800.xor: Marvell shared XOR driver
mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq )
mv_xor f1060800.xor: freeing 1 in use descriptors!
mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( intr crc32c )
mv_xor f1060900.xor: Marvell shared XOR driver
mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq )
mv_xor f1060900.xor: freeing 1 in use descriptors!
mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( intr crc32c )
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
ahci_mv f10a8000.sata: AHCI 1.0 32 slots 2 ports 6 Gbps 0x3 impl platform mode
ahci_mv f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
scsi0 : ahci_mv_platform
scsi1 : ahci_mv_platform
ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 58
ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 58
armada-nand f10d0000.nand: 
Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC
NAND device: Manufacturer ID: 0x01, Chip ID: 0xda (AMD/Spansion NAND 
256MiB 3,3V 8-bit), 256MiB, page size: 2048, OOB size: 64
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
11 cmdlinepart partitions found on MTD device armada-nand

Creating 11 MTD partitions on "armada-nand":
0x000000000000-0x000000200000 : "uboot"
0x000000200000-0x000000220000 : "u_env"
0x000000220000-0x000000260000 : "s_env"
0x0000007e0000-0x000000820000 : "devinfo"
0x000000820000-0x000000a00000 : "sysdiag"
0x000000a00000-0x000005a00000 : "kernel"
0x000001000000-0x000005a00000 : "rootfs"
0x000005a00000-0x00000aa00000 : "alt_kernel"
0x000006000000-0x00000aa00000 : "alt_rootfs"
0x000000a00000-0x00000aa00000 : "ubifs"
0x00000aa00000-0x000010000000 : "syscfg"

bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
SoC: model = 0x6820, revision = 0x4
mvPncVirtBase = 0xe0c00000, pncTcamSize = 1 GiB
  o 3 Giga ports supported
  o SKB recycle supported for SWF (Disabled)
  o NETA acceleration mode 4
  o BM supported for CPU: 4 BM pools
  o PnC supported (Enabled)
  o RX Queue support: 8 Queues * 256 Descriptors
  o TX Queue support: 8 Queues * 532 Descriptors
  o GSO supported
  o GRO supported
  o Receive checksum offload supported
  o Transmit checksum offload supported
  o Driver ERROR statistics enabled
  o Driver INFO statistics enabled
  o Driver DEBUG statistics enabled

port #0: is_sgmii=0, is_rgmii=1, phy_addr=0
  o Loading network interface(s) for port #0: cpu_mask=0x3, tx_csum_limit=9800

  o Port 0 is connected to Linux netdevice
    o eth0, ifindex = 3, GbE port = 0
        giga p=0: mtu=1500, mac=60:38:e0:b4:47:a0 (hw config)

port #2: is_sgmii=1, is_rgmii=0, phy_addr=1
  o Loading network interface(s) for port #2: cpu_mask=0x3, tx_csum_limit=2 GiB

  o Port 2 is connected to Linux netdevice
    o eth1, ifindex = 4, GbE port = 2
        giga p=2: mtu=1500, mac=e2:d5:94:2f:af:12 (random)

(error) mv_switch_probe(5780) (rc=-22): read switch fdt file failed
mv_soho_switch: probe of switch.3 failed with error 1
  o Loading Switch QuarterDeck driver
    o Device ID     : 0x352
    o No. of Ports  : 7
    o CPU Port      : 5
    o Setting Switch Port #5 connected to GMAC port for 1000 Full with FC
    o Setting Switch Port #6 connected to GMAC port for 1000 Full with FC
gprtPhyIntEnable failed port 4
Switch driver init:
    o preset mode = Transparent
    o tag mode    = No Tag
port #0 establish switch connection

libphy: orion_mdio_bus: probed
mdio_bus f1072004.mdio-mi: cannot get PHY at address 0
mdio_bus f1072004.mdio-mi: cannot get PHY at address 1
e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
e1000: Copyright (c) 1999-2006 Intel Corporation.
e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
e1000e: Copyright(c) 1999 - 2013 Intel Corporation.


Pictures

Retail Images
User Images

See also

List of Four Stream Hardware

Retrieved from "https://techinfodepot.shoutwiki.com/w/index.php?title=Linksys_WRT3200ACM&oldid=539060"