MINEW G1-C
From TechInfoDepot
Jump to navigationJump to search
| bgn (N300) | |
|---|---|
| MINEW | |
 | |
| Homepage | Product page |
| 3rd Party Firmware | |
| dd-wrt | Status Unknown |
| OpenWrt | Supported |
| Tomato any flavor | Incompatible |
| Gargoyle | Status Unknown |
| Platform | |
| Brand • Model • Rev | MINEW G1-C |
| FCC ID | none specified |
| Type | IoT Gateway |
CPU1  | MediaTek MT7628AN |
| CPU1 Type | MIPS 24KEc |
| CPU1 Speed | 580 MHz |
| Flash1 Chip | Winbond W25Q128 |
| Flash1 Size | 16 MiB 16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> (SPI NOR) |
| RAM1 Size | 64 MiB 67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br /> (DDR2) |
| RAM1 Chip | Brand? Model? |
| ETH chip1 | MediaTek MT7628AN |
| Ethernet Port Count | 1-100MbE-LAN |
| Wired Standard | IEEE 802.3i/3u |
|
802dot11 OUI: none specified | |
| Stock bootloader | U-Boot |
| Expansion IF types | microSD |
| SD/MMC Slots | 1 |
| PoE | 802.3af, standard |
| Power | 5 VDC, ? A |
| Connector type | µUSB |
| Serial Port (UART) | yes, 3.3V TTL, (57600 8N1) |
|
| |
|
| |
| Other | |
|
| |
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) |
| Retail | |
| Availability | End of Life |
| Radio 1 | |
| Chip1 | MediaTek MT7628AN |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 2x2:2 |
| Wireless Standard | IEEE 802.11b/g/n |
| 802.11n | up to 300 Mbps |
| 802.11g | up to 54 Mbps |
| 802.11b | up to 11 Mbps |
| WiFi Operating Frequency | 2.4 GHz |
For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.
- • 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.) = N300 class
Flashing
 | NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
 | This device is NOT RECOMMENDED for future use with OpenWrt due to low flash/ram.
DO NOT BUY DEVICES WITH 8MB FLASH / 64MB RAM if you intend to flash an up-to-date and secure OpenWrt version onto it! See 8/64 warning for details. This device does not have sufficient resources (flash and/or RAM) to provide secure and reliable operation. This means that you will not be able to install many packages, and that you might experience crashes due to OOM situations more or less often. See OpenWrt on 8/64 devices what you can do now. |
Target: ramips
Subtarget: mt76x8
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 21.02.1
Current supported version: 25.12.2
Subtarget: mt76x8
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 21.02.1
Current supported version: 25.12.2
LAN Hardware: MediaTek MT7628AN
WLAN Hardware: MediaTek MT7628AN
WLAN Comment: MIMO 2x2:2
Installation method(s):
Sysupgrade
Comment:
Industrial rated, but not water resistant
WLAN Hardware: MediaTek MT7628AN
WLAN Comment: MIMO 2x2:2
Installation method(s):
Sysupgrade
Comment:
Industrial rated, but not water resistant
| git • >> |
|---|
ramips: add support for minew g1-c The minew g1-c is a smart home gateway / BLE gateway. A Nordic nRF52832 is available via USB UART (cp210x) to support BLE. The LED ring is a ring of 24x ws2812b connect to a generic GPIO (unsupported). There is a small LED which is only visible when the device is open which will be used as LED until the ws2812b is supported. The board has also a micro sdcard/tfcard slot (untested). The Nordic nRF52832 exposes SWD over a 5pin header (GND, VCC, SWD, SWC, RST). The vendor uses an older OpenWrt version, sysupgrade can be used via serial or ssh. CPU: MT7628AN / 580MHz RAM: DDR2 128 MiB RAM Flash: SPI NOR 16 MiB W25Q128 Ethernet: 1x 100 mbit (Port 0) (PoE in) USB: USB hub, 2x external, 1x internal to USB UART Power: via micro usb or PoE 802.11af UART: 3.3V, 115200 8n1 |
