MokerLink 10GT080M
From TechInfoDepot
Jump to navigationJump to search
| 8 Port 10G Managed Ethernet Switch | |
| Homepage | Product page |
|---|---|
| 3rd Party Firmware | |
| dd-wrt | Status Unknown |
| OpenWrt | Supported |
| Tomato any flavor | Incompatible |
| Gargoyle | Status Unknown |
| Platform | |
| Brand • Model • Rev | MokerLink 10GT080M |
CPU1  | Realtek RTL9313 |
| CPU1 Type | MIPS IA |
| CPU1 Speed | 1.0 GHz ( 2 cores ) |
| Flash1 Size | 32 MiB33,554,432 B <br />262,144 Kib <br />32,768 KiB <br />256 Mib <br />0.0313 GiB <br /> (SPI NOR) |
| RAM1 Size | 512 MiB536,870,912 B <br />4,194,304 Kib <br />524,288 KiB <br />4,096 Mib <br />0.5 GiB <br /> |
| ETH chip1 | Realtek RTL9313 |
| Switch Chip1 | Realtek RTL9313 |
| Switch Chip2 | Realtek RTL8261BE |
| Switch Chip3 | Realtek RTL8261BE |
| Switch Chip4 | Realtek RTL8261BE |
| Switch Chip5 | Realtek RTL8261BE |
| Switch Chip6 | Realtek RTL8261BE |
| Switch Chip7 | Realtek RTL8261BE |
| Switch Chip8 | Realtek RTL8261BE |
| Switch Chip9 | Realtek RTL8261BE |
| Ethernet Port Count | 8-10GbE |
| Ethernet connector | 8P8C |
| Wired Standard | IEEE 802.3i/3u/3ab/3bz/an |
| Port-based vlan | yes |
| 802.1q vlan | yes |
| Auto-MDIX | unspecified |
| Switch Class | managed |
|
Ethernet OUI: none specified | |
| Expansion IF types | SFP+ |
| SFP ports | 4 |
| Stock bootloader | U-Boot |
| Power | 100-240 VAC ~ 50/60 Hz, ? A |
| Connector type | AC |
| Serial Port (UART) | yes, 115200 8N1 |
|
| |
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) |
For a list of all currently documented Realtek chipsets with specifications, see Realtek.
Flashing
 | NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
 | The development branch can contain experimental code that is under active development and should not be used for production environments. Snapshot images may support additional hardware; however, it is experimental, considered unstable, and sometimes won't compile. |
| Prebuilt snapshot images do not come with any web interface or GUI. You will need to be comfortable using a command line and remote shell to install one yourself → How to install LuCI |
Target: realtek
Subtarget: rtl931x
Package architecture: mips_24kc
Supported Since Commit
Support started version: unknown
Current supported version: snapshot
Subtarget: rtl931x
Package architecture: mips_24kc
Supported Since Commit
Support started version: unknown
Current supported version: snapshot
LAN Hardware: Realtek RTL9313
WLAN Comment: No WLAN
Installation method(s):
U-Boot TFTP + serial recovery, see git-commit
Recovery method(s):
U-Boot TFTP + serial recovery, see git-commit
WLAN Comment: No WLAN
Installation method(s):
U-Boot TFTP + serial recovery, see git-commit
Recovery method(s):
U-Boot TFTP + serial recovery, see git-commit
| git • >> |
|---|
realtek: add support for MokerLink 10GT080M The MokerLink 10GT080M is a 12-port managed switch based on the Realtek RTL9313 SoC. Specifications: - SoC: Realtek RTL9313 - RAM: 512 MB - Flash: 32 MB SPI NOR - Ethernet: 8x 10GBASE-T (RTL8261BE), 4x SFP+ (10G) - LEDs: 1x green system status (GPIO), per-port link/activity via the SoC LED engine - Buttons: 1x reset - Power: 100-240 V AC, 50/60 Hz, up to 60 W - UART: 115200 8N1 on the front-panel RJ45 console port Working: switching on the copper and SFP+ ports, SFP hotplug and EEPROM access, copper and SFP+ port LEDs, system status LED, reset button, PHY temperature monitoring, sysupgrade, and the persistent JFFS2 overlay. Installation: Netboot the initramfs image over TFTP, then run sysupgrade from OpenWrt. Connect to the serial console and press Escape during the one-second U-Boot countdown. Configure the network parameters for the local TFTP server, then initialize the switch and boot the image: RTL9310# setenv ipaddr 192.168.1.250 RTL9310# setenv serverip 192.168.1.156 RTL9310# setenv netmask 255.255.255.0 RTL9310# rtk network on RTL9310# rtk 10g 54 dac300cm RTL9310# tftpboot 0x84f00000 openwrt-...-initramfs-kernel.bin RTL9310# bootm 0x84f00000 Port 54 is front-panel SFP+ port 12. Select the matching U-Boot media mode when using a transceiver or a different DAC length. Once OpenWrt has booted, copy the sysupgrade image to the device and install it with sysupgrade. The OpenWrt firmware partition replaces the stock RUNTIME1 partition. The stock RUNTIME2 partition remains read-only and can be booted with "boota 1" from U-Boot for recovery. MAC addresses: The base MAC comes from the U-Boot environment variable "ethaddr" in the u-boot-env partition. Per-port LAN MACs are derived sequentially. Signed-off-by: Tanner Lane Link: https://github.com/openwrt/openwrt/pull/24905 Signed-off-by: Markus Stockhausen |
