Netgear DM200
From TechInfoDepot
Jump to navigationJump to search
| Broadband High-Speed DSL Modem | |
 | |
| Homepage | Product page |
|---|---|
| Support | Support page |
| Wikipedia | Netgear |
| WikiDevi.wi-cat.ru | Netgear DM200 |
| 3rd Party Firmware | |
| dd-wrt | Status Unknown |
| OpenWrt | Supported |
| Tomato any flavor | Incompatible |
| Gargoyle | Status Unknown |
| Platform | |
| Brand • Model • Rev | Netgear DM200-100NAS |
| Type | dsl modem |
CPU1  | Lantiq PSB 80220 |
| CPU1 Type | MIPS 34Kc |
| CPU1 Speed | 500 MHz ( 2 cores ) |
| Flash1 Chip | Winbond W25Q64VSIG |
| Flash1 Size | 8 MiB 8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> |
| RAM1 Size | 64 MiB 67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br /> |
| RAM1 Chip | Brand? Model? |
| ETH chip1 | Lantiq PSB 80220 |
| DSL Ports | 1 |
| RJ11 Ports (VOIP/POTS) | 1 |
| Ethernet Port Count | 1-100MbE-LAN |
| Wired Standard | IEEE 802.3i/3u |
|
| |
| Stock bootloader | U-Boot |
| Stock FW OS | Linux 3.10.12 |
| Expansion IF types | none specified |
| Power | 12 VDC, 0.5 A |
| Connector type |
barrel 5.5 mm (OD) 9.5 mm (LEN) |
| Serial Port (UART) | yes, (115200 8N1) |
|
Flags: | |
|
| |
| Other | |
|
| |
| 3rd Party Firmware Support |
LEDE Project (obsolete, OpenWrt) • (List) , OpenWrt • (List | Dev | DLs) |
| Retail | |
| Availability | End of Life |
| End of Life date | 2021 |
| (Est.) release date | October 2016 |
| UPC |
0606449113747 (UPC DB, On eBay) |
| Newegg | N82E16825124021 |
| ASIN |
B01GL3YPHI  |
| Country of manuf | China |
For a list of all currently documented Lantiq (Intel) chipsets with specifications, see Lantiq.
For a list of all currently documented Netgear devices with specifications, see Netgear.
Overview
Flashing
 | NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
 | This device is NOT RECOMMENDED for future use with OpenWrt due to low flash/ram.
DO NOT BUY DEVICES WITH 8MB FLASH / 64MB RAM if you intend to flash an up-to-date and secure OpenWrt version onto it! See 8/64 warning for details. This device does not have sufficient resources (flash and/or RAM) to provide secure and reliable operation. This means that you will not be able to install many packages, and that you might experience crashes due to OOM situations more or less often. See OpenWrt on 8/64 devices what you can do now. |
Target: lantiq
Subtarget: xrx200
Package architecture: mips_24kc
Supported Since Commit
Support started version: 18.06.0
Current supported version: 25.12.6
Subtarget: xrx200
Package architecture: mips_24kc
Supported Since Commit
Support started version: 18.06.0
Current supported version: 25.12.6
LAN Hardware: Lantiq GSWIP (built-in SoC switch)
WLAN Comment: No WLAN
Installation method(s):
GUI generic, U-Boot TFTP recovery, see devicepage, see git-commit
Recovery method(s):
U-Boot TFTP recovery
WLAN Comment: No WLAN
Installation method(s):
GUI generic, U-Boot TFTP recovery, see devicepage, see git-commit
Recovery method(s):
U-Boot TFTP recovery
| git • >> |
|---|
lantiq: add Netgear DM200 support
Netgear DM200 is an inexpensive VDSL modem:
CPU: VRX220 MIPS 34Kc 5.6 @ 500Mhz
RAM: 64MiB
Flash: 8MiB
Ethernet: 1x100M
DSL: VDSL2+, ADSL2+
reset button, 3x bi-color LEDs
Serial port is 115200 baud, on the 4 pin header; pins from the bottom to
top are GND, RX, TX.
To upgrade from the vendor firmware, upload factory.img
The DM200 bootloader supports flashing over TFTP; hold the reset button
while powering on the device, and wait for the power light to start
flashing green before releasing. The device is now listening on
192.168.0.1/24, and can be sent a factory.img or a netgear image with a
TFTP put.
Once the image is loaded, it will be written to the flash, and the
device will reboot; this will take a few minutes.
Thanks to Edward O'Callaghan and Baptiste Jonglez, who implemented their
own ports for this device and provided valuable feedback.
Signed-off-by: Thomas Nixon
|
