Netgear WNDAP660

From TechInfoDepot
Jump to navigationJump to search
abgn (AN900)
ProSafe 3x3 Dual Radio, Dual Band Wireless-N Access Point
Support Support page
Wikipedia Netgear
WikiDevi.wi-cat.ru Netgear WNDAP660
3rd Party Firmware
dd-wrt Status Unknown
OpenWrt Supported
Tomato any flavor Incompatible
Gargoyle Status Unknown
Platform
Brand • Model • Rev Netgear WNDAP660-100NAS
FCC ID PY312200203, NKR-DNXAG1
IC ID 4054A-12200203
Board ID 48DNXA07.0GB
Type access point
CPU1 Question? Applied Micro APM82181
CPU1 Type PowerPC 464
CPU1 Speed 1.0 GHz
Flash1 Chip SK hynix HY27US08561A-TPCB
Flash1 Size 32 MiB 33,554,432 B <br />262,144 Kib <br />32,768 KiB <br />256 Mib <br />0.0313 GiB <br />
RAM1 Size 256 MiB 268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br />
RAM1 Chip SK hynix H5PS1G63EFR-Y5C x 2
ETH chip1 Applied Micro APM82181
Switch Realtek RTL8363SB
Ethernet Port Count 2-1GbE-LAN
Wired Standard IEEE 802.3i/3u/3ab

802dot11 OUI: 84:1B:5E (8 E, 10 W)
Ethernet OUI: 84:1B:5E (8 E, 10 W)

Stock bootloader U-Boot 2009.08-wndap660_620
Stock FW OS Linux 2.6.36.2
Expansion IF types Mini PCIe
Mini PCIe slots 2
PoE 802.3at, standard
Power 12 VDC, 1.5 A
Connector type barrel
5.5 mm (OD)
2.5 mm (ID)
9.5 mm (LEN)
Serial Port (UART) yes, RJ-45, (9600 8N1)
JTAG Port yes, 16-pin header, populated, J4

Flags:
PoE in, SNMP

Additional chips
3-Lane 3-Port PCI Express Switch;IDT;89HPES3T3;;1;
Frequency Generator for PCIe, USB, QPI & SATA;IDT;9FG104DGLF;;1;
Multichannel RS-232 Line Driver;Texas Instruments;MA3232C;;1;
802.3at, High Efficiency, PoE & DC/DC Controller; TI;TPS23754;;2;
Adjustable, 300mA LDO Regulator w/ Enable;Richtek;RT9179;;2;
5A, 24V, 570kHz Step-Down Converter;Richtek;RT8251;;2;
TVS ESD Diode Array;Bourns;CDDFN10-2574N;;4;
3A, 28V Step-Down Converter;TI;TPS54331;;2;

Other

Default SSID: NETGEAR_11ng (3 addl. devices)
Default IP address: 192.168.0.100
the IP 192.168.0.100 is used by 18 additional devices
of which 10 are Netgear devices
Default login user: admin
Default login password: password
admin:password credentials used by 428 additional devices
of which 307 are Netgear devices

Manuf/OEM/ODM Wistron NeWeb
3rd Party Firmware Support OpenWrt • (List | Dev | DLs)
Retail
Availability End of Life
FCC approval date 16 August 2012
UPC 606449082227
(UPC DB, On eBay)
ASIN B0098QUUES
Country of manuf China
Radio 1
Radio1 module Wistron NeWeb DNXA-G1
Radio1 module IF Mini PCIe
Chip1 Atheros AR9380
Wireless interface OUI 84:1B:5E
Antenna Connector Type U.FL
MIMO status 3x3:3
Wireless Standard IEEE 802.11a/b/g/n
802.11n up to 450 Mbps
802.11g up to 54 Mbps
802.11b up to 11 Mbps
802.11a up to 54 Mbps
WiFi Operating Frequency 2.4 or 5 GHz
Radio 2
Radio2 module Wistron NeWeb DNXA-G1
Radio2 module IF Mini PCIe
Chip1 Atheros AR9380
Wireless interface OUI 84:1B:5E
Antenna Connector Type U.FL, RP-SMA
MIMO status 3x3:3
Wireless Standard IEEE 802.11a/b/g/n
802.11n up to 450 Mbps
802.11g up to 54 Mbps
802.11b up to 11 Mbps
802.11a up to 54 Mbps
WiFi Operating Frequency 2.4 or 5 GHz
 FCC ID
Netgear WNDAP620PY312200202
NKR-DNXAG1
Wistron NeWeb DNXA-G1NKR-DNXAH1
NKR-DNXAG1
PY312200202

For a list of all currently documented Applied Micro (AMCC) SoC's with specifications, see Applied Micro.
For a list of all currently documented Atheros (QCA) chipsets with specifications, see Atheros.
For a list of all currently documented Realtek chipsets with specifications, see Realtek.

For a list of all currently documented Netgear devices with specifications, see Netgear.

• 450 Mbps - 3SS 2.4GHz 802.11n (40MHz chan.),
• 450 Mbps - 3SS 5GHz 802.11n (40MHz chan.) = AN900 class

Overview

"48DNXA07.0GB", "(XB114_030)", and "2011/04/13" is silkscreened

on the wireless modules in the FCC photos. (OEM: Wistron NeWeb)

This device is the dual channel, dual band version of the WNDAP620.

Two (dual-band) DNXA-G1's would appear to be used.

Per /proc/pci/devices output from a device, each uses

a 168c:0030 PCI ID (default for Atheros AR938x).

Links of Interest

News

Flashing

Flashing OpenWrt

Target: apm821xx
Subtarget: nand
Package architecture: powerpc_464fp
[NETGEAR WNDAP660 Supported Since Commit]
Support started version: 19.07.0
Current supported version: 25.12.0
LAN Hardware: RealTek RTL8363SB
WLAN Hardware: Atheros AR9380 (mini-PCIe)
Installation method(s):
U-Boot TFTP + serial recovery, see git-commit
Install Comment:
Currently requires connection to external RS232 (not TTL) serial port (9600,8n1) with Cisco Console compatible 8P8C ("RJ45") cable. Detailed installation instructions can be found at the "Supported Since Commit" link at the top of this page. Modify instructions to match the filename you are installing (e.g. "openwrt-21.02.0-apm821xx-nand-netgear_wndap660-squashfs-factory.img" instead of "openwrt-apm821xx-nand-netgear_wndap660-squashfs-factory.img". Use linux "crc32" command to compute crc32 of factory.img during check step before flashing.
Recovery method(s):
U-Boot TFTP + serial recovery, see git-commit
Comment:
crc32 for "openwrt-21.02.0-apm821xx-nand-netgear_wndap660-squashfs-factory.img" is: c6c77d05
git • >> 
apm821xx: add support for the Netgear WNDAP620 and WNDAP660
This patch adds support for the Netgear WNDAP620 and WNDAP660,
they are similar devices, but due to the LAN LED configuration,
the switch setup and WIFI configuration each gets a different
device target.

Hardware Highlights WNDAP620:
CPU: AMCC PowerPC APM82181 at 1000 MHz
DRAM:  128 MB, 2 x 64 MiB DDR2 SK hynix H5PS5162GF
CPU: AMCC PowerPC APM82181 at 1000 MHz
FLASH: 32 MiB, NAND SLC, SK hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY - Only 1 GBit Port (POE)
Wifi: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 3 internal dual-band antennae + 3 x RSMA for external antennaes

Hardware Highlights WNDAP660:
CPU: AMCC PowerPC APM82181 at 1000 MHz + 2 Heatsinks
DRAM:  256 MB, 2 x 128 MiB DDR2
FLASH: 32 MiB, NAND SLC, SK hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY (POE)
Wifi1: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Wifi2: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, 2x dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 6 internal dual-band antennae + 3 x RSMA for external antennaes

Flashing requirements:

 - needs a tftp server at 192.168.1.10/serverip.
 - special 8P8C(aka RJ45)<->D-SUB9 Console Cable
   ("Cisco Console Cable"). Note: Both WNDAP6x0 have
   a MAX3232 transceivers, hence no need for any separate
   CMOS/TTL level shifters.

External Antenna:
The antennae mux is controlled by GPIO 11 and GPIO14. Valid Configurations:
 = Config# = | = GPIO 11 = | = GPIO 14 = |  ===== Description =====
      1.     |   1 / High  |  0 / Low    | Use the internal antennae (default)
      2.     |   0 / Low   |  1 / High   | Use the external antennae

The external antennaes are only meant for the 2.4 GHz band.

One-way Flashing instructions via u-boot:

 0. connect the serial cable to the RJ45 Console Port
    Note: This requires a poper RS232 and not a TTL/USB adaptor.

 1. power up the AP and interrupt the u-boot process at

    'Hit any key to stop autoboot'

 2. setup serverip and ipaddr env settings
    Enter the following commands into the u-boot shell
    # setenv ipaddr 192.168.1.1
    # setenv serverip 192.168.1.10

 3. download the factory.img image to the AP
    Enter the following commands into the u-boot shell

    # tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-squashfs-factory.img

 4. verfiy image integrity
    Enter the following commands into the u-boot shell

    # crc32 $fileaddr $filesize

    If the calculated crc32 checksum does not match, go back to step 3.

 5. flash the image
    Enter the following commands into the u-boot shell

    # nand erase 0x110000 0x1bd0000
    # nand write ${kernel_addr_r} 0x110000 ${filesize}

 6. setup uboot environment
    Enter the following commands into the u-boot shell

    # setenv bootargs
    # setenv fileaddr
    # setenv filesize
    # setenv addroot 'setenv bootargs ${bootargs} root=/dev/ubiblock0_0'
    # setenv owrt_boot 'nboot ${kernel_addr_r} nand0 0x110000; run addroot; run addtty; bootm ${kernel_addr_r}'
    # setenv bootcmd 'run owrt_boot'
    # saveenv

 7. boot
    # run bootcmd

Booting initramfs instructions via u-boot:

 Follow steps 0 - 2 from above.

 3. boot initramfs
    Enter the following commands into the u-boot shell

    # tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-initramfs-kernel.bin
    # run addtty
    # bootm ${kernel_addr_r}

See also

Retrieved from "https://techinfodepot.shoutwiki.com/w/index.php?title=Netgear_WNDAP660&oldid=519911"