* boot messages from bootloader and Linux loading Netgear firmware v1.0.30NA
Decompressing..........done
Decompressing..........done
WNDR3300 Boot code V1.0.2
Build date: Thu Sep 20 13:11:58 CST 2007
Initializing Arena
Initializing Devices.
Boot partition size = 131072(0x20000)
et0: Broadcom BCM47xx 10/100 {{abbr|Mbps|Megabits per second}} Ethernet Controller 4.150.10.5
et1: Broadcom BCM47xx 10/100 {{abbr|Mbps|Megabits per second}} Ethernet Controller 4.150.10.5
CPU type 0x29006: 264{{abbr|MHz|megahertz}}
Total memory: 16384 KBytes
Device eth0: hwaddr 00-1E-2A-5C-2F-CD, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
CPU revision is: 00029006
Primary instruction cache 16kb, linesize 16 bytes (2 ways)
Primary data cache 16kb, linesize 16 bytes (2 ways)
Linux version 2.4.20 (builder@dev2) (gcc version 3.2.3 with Broadcom modifications) #33 Fri Jan 11 12:58:25 CST 2008
Setting the PFC to its default value
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
CPU: BCM4704 rev 9 at 264 {{abbr|MHz|megahertz}}
Calibrating delay loop... 262.96 BogoMIPS
Memory: 14584k/16384k available (1254k kernel code, 1800k reserved, 104k data, 56k init, 0k highmem)
Dentry cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
PCI: Initializing host
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Fixing up bus 1
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
Squashfs 2.2-r2 (released 2005/09/08) (C) 2002-2005 Phillip Lougher
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xb8000300 (irq = 3) is a 16550A
ttyS01 at 0xb8000400 (irq = 0) is a 16550A
PPP generic driver version 2.4.2
Amd/Fujitsu Extended Query Table v1.1 at 0x0040
number of CFI chips: 1
Flash device: 0x400000 at 0x1c000000
Physically mapped flash: squashfs filesystem found at block 585
Creating 8 MTD partitions on "Physically mapped flash":
0x00000000-0x00020000 : "boot"
0x00020000-0x003b0000 : "linux"
0x000927f8-0x003b0000 : "rootfs"
0x003b0000-0x003c0000 : "T_Meter1"
0x003c0000-0x003d0000 : "T_Meter2"
0x003d0000-0x003e0000 : "POT"
0x003e0000-0x003f0000 : "board_data"
0x003f0000-0x00400000 : "nvram"
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
802.1Q VLAN Support v1.7 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 56k freed
Algorithmics/MIPS FPU Emulator v1.5
Reading board data...
WSC UUID: 0x450a40ee3f68bd4033ee9a405928c362
Using /lib/modules/2.4.20/kernel/drivers/net/et/et.o
insmod: bcm57xx.o: no module by that name found
Using /lib/modules/2.4.20/kernel/drivers/net/wl/wl.o
Hit enter to continue...Reading board data...
WSC UUID: 0x450a40ee3f68bd4033ee9a405928c362
WARNING: console log level set to 1
eth2: Numerical result out of range
eth2: Operation not supported
eth2: Invalid argument
eth2: Operation not supported
eth2: Operation not supported
eth3: Numerical result out of range
eth3: Operation not supported
eth3: Invalid argument
eth3: Invalid argument
eth4: No such device
ifconfig: Illegal seek
*********************************************
Wi-Fi Simple Config Application - Intel Corp.
Version: Build 1.0.5, November 19 2006
*********************************************
Initializing stack...button monitor start...!
apLockDownLog_init, counttion = 300, duration = 300!
OK
Now starting stack
get mac = 00 1E 2A 5C 2F CC
DEVICE PIN: 63204810
eth2: ignore i/f due to error(s)
eth3: ignore i/f due to error(s)
Reading board data...
WSC UUID: 0x450a40ee3f68bd4033ee9a405928c362
Using /lib/modules/2.4.20/kernel/net/ipv4/acos_nat/acos_nat.o
info, udhcp server (v0.9.8) started
error, unable to parse 'option wins '
error, unable to parse 'option domain '
Info: No FWPT default policies.
POT integrity check OK.
POT time is up.
Start DHCP client daemon
info, udhcp client (v0.9.8) started
UTX 0x01
URX 0x01
DTX 0x01
DRX 0x01
eth1: No such process
Hit enter to continue...
******* MODE: Access Point *******
DEVICE PIN:63204810
WSC: In unconfiged AP mode, wait for start command....
tlvPtrChar* : func CMasterControl_InitiateRegistration line 656 allocating memory 0x10003680 for 0x10003668
Waiting for Registrar to connect...
BusyBox v0.60.0 (2008.01.11-04:58+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
#
