4.MXIC SPI (4 MByte)!
---JWNR2000v2 at 2011.12.12-11:14+0800 version v2.1 [16bit](390MHz)
### Press down Reset button(GPIOA5) to reset the Router Configuration!! ###
no sys signature at 00010000!
system signature at 00020000!
rootfs signature at 000D0000!
### Press down Esc key to escape booting by user!! ###
Set 8196C PHY Patch OK
NMRP Client starts Listening for ADVERTISE...
NMRP timeoust exit;
decompressing kernel:
Uncompressing Linux... done, booting the kernel.
done decompressing kernel.
early printk enabled
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock7 console=0
Calibrating delay loop... 389.12 BogoMIPS
Memory: 24096k/32768k available (2076k kernel code, 8672k reserved, 241k data, 56k init, 0k highmem)
Dentry-cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode-cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
check_wait... unavailable.
POSIX conformance testing by UNIFIX
Initializing RT netlink socket
Starting kswapd
pty: 10 Unix98 ptys configured
state->flags=00000000
Realtek GPIO Driver for Flash Reload Default
block: 64 slots per queue, batch=16
SPI INIT
flash device: 0x200000 at 0xbd000000
probe realtek
get SPI CS0
maker:c2 type:20 sector_cnt:64
get SPI CS1
maker:0 type:0 sector_cnt:0
MXIC matched!!get SPI chip driver!
probe ends
probe realtek2
Creating 10 MTD partitions on "Physically mapped flash":
0x00000000-0x00008000 : "boot+hw_setting"
0x00008000-0x0000a000 : "pot"
0x0000a000-0x0000c000 : "pppoe"
0x0000c000-0x0000e000 : "reserve1"
0x0000e000-0x00010000 : "reserve2"
0x00010000-0x00020000 : "nvram"
0x00020000-0x000d0000 : "kernel"
0x000d0000-0x003b0000 : "root fs"
0x003b0000-0x003c0000 : "trafficmeter"
0x003c0000-0x00400000 : "language_table"
RTL8192C/RTL8188C driver version 1.4 (2010-12-22)
=====>>INSIDE rtl8192cd_init_one <<=====
vendor_deivce_id=819110ec
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
=====>>EXIT rtl8192cd_init_one <<=====
=====>>INSIDE rtl8192cd_init_one <<=====
=====>>EXIT rtl8192cd_init_one <<=====
TCP: Hash tables configured (established 2048 bind 4096)
ip_conntrack version 2.1 (512 buckets, 4096 max) - 356 bytes per conntrack
ip_conntrack_rtsp v0.01 loading
ip_nat_rtsp v0.01 loading
PPTP netfilter connection tracking: registered
PPTP netfilter NAT helper: registered
ip_tables: (C) 2000-2002 Netfilter core team
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 56k freed
mount /proc file system ok!
mount /var file system ok!
mtd = /dev/nvram
flatfsd: flat1_checkfs 4, hdr.magic=cafe2345, hdr.length=14508, hdr.chksum=1290928
flatfsd: Created 8 configuration files (14223 bytes)
Wed Jan 1 00:00:00 UTC 2003
firmware_version = V1.0.0.3_1.0.10
Using /lib/modules/2.4.18/fastpath.o
Realtek FastPath v1.18
Using /lib/modules/2.4.18/dni-qos.o
dni-qos module init at dev:eth1, real_dev:eth1
Using /lib/modules/2.4.18/ipt_CONENAT.o
Using /lib/modules/2.4.18/ipt_DNS_HIJACK.o
Using /lib/modules/2.4.18/ip_conntrack_starcraft.o
Using /lib/modules/2.4.18/ip_nat_starcraft.o
Using /lib/modules/2.4.18/lan_port_resv.o
Using /lib/modules/2.4.18/delete_conntrack.o
Using /lib/modules/2.4.18/ipt_string.o
Using /lib/modules/2.4.18/ip_conntrack_proto_esp.o
Using /lib/modules/2.4.18/ip_nat_proto_esp.o
PID:mtd = /dev/nvram
flatfsd: Wrote 14508 bytes to flash in 0 seconds
SSID:OnNetworks03PASSPHRASE:53602068Configuring LAN , lan_ifname = br0 ........
Set 8196C PHY Patch OK
IF_handle start....
wps start
cat: /tmp/wscd_lock_stat: No such file or directory
[wsc]main 6645:daemon parameter:
wscd -start -c /var/wsc.conf -w wlan0 -fi /var/wscd-wlan0.fifo -daemon
Read config file:/var/wsc.conf, def:0
configured pin_timeout = 240
[wsc]init_config 6296:auth_type_flags:21
[wsc]init_config 6300:encrypt_type_flags:09
<<====WPS argument list=====>>
is_ap = 1
role = Registrar
config_state = configured
config_method = 0x2688
pin_code = 20202330
upnp = 1
wlan0_wsc_disabled=0
auth_type_flags:0x21
encrypt_type_flags:9
---wlan0 setting---
rf_band = 1; 1=2.4G ;2=5G
SSID=OnNetworks03
security mixed mode = 0
Auth_Type=32
Encrypt_Type=8
WSC_PSK = 53602068
wlan0 interface wsc is Enabled
button_hold_time = 3
SSID-prefix = OnNetworks_
disable_configured_by_exReg = 0
uuid=63041253101920061228841b5e832259
brute_force_attack_mitigation ThresHold[3]
wsc version=2.0
<<====WPS argument list=====>>
<< Start_upnp >>
WSCRegisterCallBackFunc successfully!
WiFi Simple Config v2.10-wps2.0 (2012.06.05-04:17+0000).
starting app
[util]build_probe_rsp_ie,2377:config method(0x1008)=2008
[wsc]main 6878:alarm(1)---------->
$Starting udhcpd:
error, Failure parsing line 10 of /var/udhcpd.conf
info, udhcpd (v0.9.9-pre) started
error, max_leases value (254) not sane, setting to 253 instead
error, Unable to open /tmp/udhcpd.leases for reading
The attached devices demo is Running ...
$Starting Service:
The abbreviation of English is Eng!
reload_language_table::Didn't find the language table we need!
gui_region = English
region = English, download_region =
Update string table successfully, memory usage: 292KB.
The httpd server is running ...
$Starting syslogd:
route: SIOC[ADD|DEL]RT: No such process
$Starting miniigd:
MiniIGD v1.07 (2012.06.05-04:17+0000).
$Starting mini_upnpd:
$Starting dnsmasq:
No nameserver in /var/resolv.conf
Static routes setting:
WAN is down
The telnetenable is running ...
device eth5 is not a slave of br0
/etc/rc.d/service_start.sh: 186: /sbin/cmd_traffic_meter: not found
$Starting /usr/sbin/lld2d:
flash:: open /tmp/upnp_portmap failed
$Starting WAN:
$Starting udhcpc:
info, udhcpc (v0.9.9-pre) started
udhcpc -i eth1 -p /var/run/udhcpc.pid -s /etc/udhcpc/udhcpc.script -h N300R &
deconfig
interface=eth1
BusyBox v1.01 (2012.06.05-04:16+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
/ # ##POT area valid.
Start sending discover ...
#### firmware_checking ####
|
