Open-Mesh OM2P-HS v4

multiple revisions of this device, use caution

bgn (N300)
OM2P-HS 300Mbps Access Point
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	Open-Mesh OM2P-HS v4
FCC ID	none specified
Type	mesh node, access point
CPU1 Y	Qualcomm Atheros QCA9533
CPU1 Speed	650 MHz
Flash1 Chip	Brand? Model?
Flash1 Size	16 MiB 16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br />
RAM1 Size	64 MiB 67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br />
RAM1 Chip	Brand? Model?
ETH chip1	Qualcomm Atheros QCA9533
Switch	Qualcomm Atheros QCA9533
Ethernet Port Count	2-100MbE-LAN
Wired Standard	IEEE 802.3i/3u
802dot11 OUI: none specified
Stock bootloader	U-Boot
Expansion IF types	none specified
PoE	802.3af, standard
Power	12-24 VDC, 1 A
Serial Port (UART)	yes
Other
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Radio 1
Chip1	Qualcomm Atheros QCA9533
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11b/g/n
802.11n	up to 300 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
CPU1 brand Radio1 chip1 brand Radio1 chip2 brand Open-Mesh OM2P v1 Atheros Atheros Open-Mesh OM2P v2 Atheros Atheros Open-Mesh OM2P v4 Qualcomm Atheros Qualcomm Atheros Open-Mesh OM2P-HS v1 Atheros Atheros Open-Mesh OM2P-HS v2 Atheros Atheros Open-Mesh OM2P-HS v3 Atheros Atheros Open-Mesh OM2P-HS v4 Qualcomm Atheros Qualcomm Atheros Open-Mesh OM2P-LC Atheros Atheros

For a list of all currently documented Qualcomm Atheros (QCA) chipsets with specifications, see Qualcomm Atheros.

For a list of all currently documented Open-Mesh devices with specifications, see Open-Mesh.

• 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.) = N300 class

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)

Target: ath79
Subtarget: generic
Package architecture: mips_24kc
Supported Since Commit
Support started version: 21.02.0
Current supported version: 25.12.2

LAN Hardware: Qualcomm Atheros QCA9533
WLAN Hardware: Qualcomm Atheros QCA9533
WLAN Comment: MIMO 2x2:2
Installation method(s):
U-Boot TFTP + serial recovery, see git-commit

git • >>

ath79: Add support for OpenMesh OM2P-HS v4 Device specifications: ====================== * Qualcomm/Atheros QCA9533 v2 * 650/600/217 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 2T2R 2.4 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + 24V passive POE (mode B) + used as WAN interface - eth1 + 802.3af POE + builtin switch port 1 + used as LAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin