P&W R619AC 64M
From TechInfoDepot
Jump to navigationJump to search
| abgn+ac (AC1200) | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Gigabit Smart wifi router Dual-band | |||||||||||||
|
| |||||||||||||
| 3rd Party Firmware | |||||||||||||
| dd-wrt | Status Unknown | ||||||||||||
| OpenWrt | Supported | ||||||||||||
| Tomato any flavor | Incompatible | ||||||||||||
| Gargoyle | Status Unknown | ||||||||||||
| Platform | |||||||||||||
| Brand • Model • Rev | P&W R619AC 64M | ||||||||||||
| FCC ID (fcc.io) | none specified | ||||||||||||
| FCC ID (fcc.report) | none specified | ||||||||||||
| Type | wireless router | ||||||||||||
| CPU1 | Qualcomm IPQ4019 | ||||||||||||
| CPU1 Type | ARM Cortex-A7 | ||||||||||||
| CPU1 Speed | 718 MHz ( 4 cores ) | ||||||||||||
| Flash1 Chip | Brand? Model? | ||||||||||||
| Flash1 Size | 64 MiB 67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br /> (NAND) | ||||||||||||
| Flash2 Size | 16 MiB16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> (NOR) | ||||||||||||
| RAM1 Size | 512 MiB 536,870,912 B <br />4,194,304 Kib <br />524,288 KiB <br />4,096 Mib <br />0.5 GiB <br /> | ||||||||||||
| RAM1 Chip | Brand? Model? | ||||||||||||
| ETH chip1 | Qualcomm IPQ4019 | ||||||||||||
| Switch | Qualcomm Atheros QCA8075 | ||||||||||||
| Ethernet Port Count |
1-1GbE-WAN 4-1GbE-LAN | ||||||||||||
| Wired Standard | IEEE 802.3i/3u/3ab | ||||||||||||
|
802dot11 OUI: none specified | |||||||||||||
| Stock bootloader | U-Boot | ||||||||||||
| Expansion IF types | Mini PCIe, USB 3.0 | ||||||||||||
| Mini PCIe slots | 1 | ||||||||||||
| USB ports | 1 | ||||||||||||
| USB Hub Compatible | Untested | ||||||||||||
| Power | 12 VDC, 1.5 A | ||||||||||||
| Serial Port (UART) | yes, 3.3V TTL, (115200 8N1) | ||||||||||||
|
| |||||||||||||
|
| |||||||||||||
| Other | |||||||||||||
|
| |||||||||||||
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) | ||||||||||||
| Retail | |||||||||||||
| ASIN |
B07DL1PJ41 multiple uses | ||||||||||||
| Radio 1 | |||||||||||||
| Chip1 | Qualcomm IPQ4019 | ||||||||||||
| Wireless interface OUI | none specified | ||||||||||||
| Antenna Connector Type | none specified | ||||||||||||
| MIMO status | 2x2:2 | ||||||||||||
| Wireless Standard | IEEE 802.11b/g/n | ||||||||||||
| 802.11n | up to 300 Mbps | ||||||||||||
| 802.11g | up to 54 Mbps | ||||||||||||
| 802.11b | up to 11 Mbps | ||||||||||||
| WiFi Operating Frequency | 2.4 GHz | ||||||||||||
| Radio 2 | |||||||||||||
| Chip1 | Qualcomm IPQ4019 | ||||||||||||
| Wireless interface OUI | none specified | ||||||||||||
| Antenna Connector Type | none specified | ||||||||||||
| MIMO status | 2x2:2 | ||||||||||||
| Wireless Standard | IEEE 802.11a/n/ac | ||||||||||||
| 802.11ac | up to 867 Mbps | ||||||||||||
| 802.11n | up to 300 Mbps | ||||||||||||
| 802.11a | up to 54 Mbps | ||||||||||||
| WiFi Operating Frequency | 5 GHz | ||||||||||||
| |||||||||||||
For a list of all currently documented Qualcomm chipsets with specifications, see Qualcomm.
For a list of all currently documented Qualcomm Atheros (QCA) chipsets with specifications, see Qualcomm Atheros.
Flashing
| NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
Target: ipq40xx
Subtarget: generic
Package architecture: arm_cortex-a7_neon-vfpv4
Supported Since Commit
Support started version: 22.03.0
Current supported version: 24.10.4
Subtarget: generic
Package architecture: arm_cortex-a7_neon-vfpv4
Supported Since Commit
Support started version: 22.03.0
Current supported version: 24.10.4
LAN Hardware: Qualcomm Atheros QCA8075
WLAN Hardware: Qualcomm Atheros IPQ4019
WLAN Comment: MIMO 2x2:2
Installation method(s):
GUI OEM, Sysupgrade, U-Boot TFTP + serial recovery, see git-commit
Recovery method(s):
U-Boot TFTP + serial recovery
Comment:
miniPCIe requires hardware mod, otherwise only USB functionality available.
WLAN Hardware: Qualcomm Atheros IPQ4019
WLAN Comment: MIMO 2x2:2
Installation method(s):
GUI OEM, Sysupgrade, U-Boot TFTP + serial recovery, see git-commit
Recovery method(s):
U-Boot TFTP + serial recovery
Comment:
miniPCIe requires hardware mod, otherwise only USB functionality available.
| git • >> |
|---|
ipq40xx: add support for P&W R619AC (aka G-DOCK 2.0) P&W R619AC is a IPQ4019 Dual-Band AC1200 router. It is made by P&W (p2w-tech.com) known as P&W R619AC but marketed and sold more popularly as G-DOCK 2.0. Specification: * SOC: Qualcomm Atheros IPQ4019 (717 MHz) * RAM: 512 MiB * Flash: 16 MiB (NOR) + 128 MiB (NAND) * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) * Wireless: - 2.4 GHz b/g/n Qualcomm Atheros IPQ4019 - 5 GHz a/n/ac Qualcomm Atheros IPQ4019 * USB: 1 x USB 3.0 * LED: 4 x LAN, 1 x WAN, 2 x WiFi, 1 x Power (All Blue LED) * Input: 1 x reset * 1 x MicroSD card slot * Serial console: 115200bps, pinheader J2 on PCB * Power: DC 12V 2A * 1 x Unpopulated mPCIe Slot (see below how to connect it) * 1 x Unpopulated Sim Card Slot Installation: 1. Access to tty console via UART serial 2. Enter failsafe mode and mount rootfs <https://openwrt.org/docs/guide-user/troubleshooting/failsafe_and_factory_reset> 3. Edit inittab to enable shell on tty console `sed -i 's/#ttyM/ttyM/' /etc/inittab` 4. Reboot and upload `-nand-factory.bin` to the router (using wget) 5. Use `sysupgrade` command to install Another installation method is to hijack the upgrade server domain of stock firmware, because it's using insecure http. This commit is based on @LGA1150(at GitHub)'s work <https://github.com/LGA1150/openwrt/commit/a4932c8d5a275d1fb4297bd20ec03f9270a45d1c> With some changes: 1. Added `qpic_bam` node in dts. I don't know much about this, but I observed other dtses have this node. 2. Removed `ldo` node under `sd_0_pinmux`, because `ldo` cause SD card not working. This fix is from <https://github.com/coolsnowwolf/lede/commit/51143b4c7571f717afe071db60bbb4db1532cbf2> 3. Removed the 32MB NOR variant. 4. Removed `cd-gpios` in `sdhci` node, because it's reported that it makes wlan2g led light up. 5. Added ethphy led config in dts. 6. Changed nand partition label from `rootfs` to `ubi`. About the 128MiB variant: The stock bootloader sets size of nand to 64MiB. But most of this devices have 128MiB nand. If you want to use all 128MiB, you need to modify the `MIBIB` data of bootloader. More details can be found on github: <https://github.com/openwrt/openwrt/pull/3691#issuecomment-818770060> For instructions on how to flash the MIBIB partition from u-boot console: <https://github.com/openwrt/openwrt/pull/3691#issuecomment-819138232> About the Mini PCIe slot: (from "ygleg") "The REFCLK signals on the Mini PCIe slot is not connected on this board out of the box. If you want to use the Mini PCIe slot on the board, you need to (preferably) solder two 0402 resistors: R436 (REFCLK+) and R444 (REFCLK-)..." This and much more information is provoided in the github comment: <https://github.com/openwrt/openwrt/pull/3691#issuecomment-968054670> |
Categories:
- P&W
- Embedded system/wireless router
- Embedded System Qualcomm
- Embedded System IPQ4019
- Qualcomm
- Embedded System ARM
- Embedded System Cortex-A7
- Embedded System Qualcomm Atheros
- Embedded System QCA8075
- Qualcomm Atheros
- OpenWrt Supported
- Has Mimo Status
- Embedded System IEEE 802.11b/g/n
- Embedded System IEEE 802.11a/n/ac
- Dual-Radio Wireless Embedded System
- Wireless Embedded System
- Dual-Band
- Embedded System
- English Documentation