pakedge WR-1

From TechInfoDepot
Jump to navigationJump to search
abgn+ac (AC1200)
802.11ac Dual Band Wireless Router
Homepage Product page
WikiDevi.wi-cat.ru Pakedge WR-1
3rd Party Firmware
dd-wrt Status Unknown
OpenWrt Supported
Tomato any flavor Incompatible
Gargoyle Status Unknown
Platform
Brand • Model • Rev pakedge WR-10.20 LFP v1.00
FCC ID SLYWR1X22
IC ID 12633A-WR1X22
Board ID 7016A1374004
Type wireless router
CPU1 checkY Qualcomm IPQ4018
CPU1 Type ARMv7 Cortex-A7
CPU1 Speed 717 MHz ( 4 cores )
Flash1 Chip Spansion S25FL256SAIFR0
Flash1 Size 32 MiB 33,554,432 B <br />262,144 Kib <br />32,768 KiB <br />256 Mib <br />0.0313 GiB <br /> (SPI NOR)
RAM1 Size 256 MiB 268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br /> (DDR3L SDRAM)
RAM1 Chip Nanya NT5CC128M16IP-DI
ETH chip1 Qualcomm IPQ4018
Switch Qualcomm Atheros QCA8075
Ethernet Port Count 1-1GbE-WAN
4-1GbE-LAN
Wired Standard IEEE 802.3i/3u/3ab

802dot11 OUI: none specified

Stock bootloader U-Boot
Expansion IF types USB 2.0
USB ports 1
USB Hub Compatible Untested
Power 12 VDC, 1.5 A
Connector type barrel
5.5 mm (OD)
2.5 mm (ID)
9.5 mm (LEN)
Serial Port (UART) yes, 4-pin header, populated, J5, 3.3V TTL, (115200 8N1)

Flags:
Wave2, MU-MIMO

Additional chips
2.4GHz WLAN/BT FEM;Skyworks;SKY85303-11;SKY11, 85303, 617FP;2;
5GHz Front End Module;Qorvo;RFFM4558;4558, B0ZX;2;

Other

Default IP address: 192.168.1.1
the IP 192.168.1.1 is used by 1359 additional devices
of which 0 are pakedge devices
Default login user: admin
Default login password: admin
admin:admin credentials used by 1358 additional devices
of which 0 are pakedge devices

Manuf/OEM/ODM Senao
3rd Party Firmware Support OpenWrt • (List | Dev | DLs)
Retail
FCC approval date 07 September 2017
(Est.) initial retail price (in USD): $300
Country of manuf Taiwan
Radio 1
Chip1 Qualcomm IPQ4018
Wireless interface OUI none specified
Antenna Connector Type none specified
MIMO status 2x2:2
Wireless Standard IEEE 802.11a/n/ac
802.11ac up to 867 Mbps
802.11n up to 300 Mbps
802.11a up to 54 Mbps
WiFi Operating Frequency 5 GHz
Radio 2
Chip1 Qualcomm IPQ4018
Wireless interface OUI none specified
Antenna Connector Type none specified
MIMO status 2x2:2
Wireless Standard IEEE 802.11b/g/n
802.11n up to 300 Mbps
802.11g up to 54 Mbps
802.11b up to 11 Mbps
WiFi Operating Frequency 2.4 GHz

For a list of all currently documented Qualcomm chipsets with specifications, see Qualcomm.
For a list of all currently documented Qualcomm Atheros (QCA) chipsets with specifications, see Qualcomm Atheros.

For a list of all currently documented pakedge devices with specifications, see pakedge.

• 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.),
• 867 Mbps - 2SS 5GHz 802.11ac (80MHz chan.) = AC1200 class

Overview

"WR-1-0.20 LFP" is silkscreened on the board in the FCC photos.

OEM: Senao (PCB ID: 7016A1374004)

The user manual on the FCC suggests that the default username/password is pakedge/pakedger but the label sample says admin/admin.

Links of Interest

Hardware specification

  • CPU: Qualcomm IPQ4018 @717MHz Quad-Core ARM (Cortex-A7)
  • Storage: 32MB (SPI NOR) Flash
  • Memory: 256MB (DDR3L) SDRAM
  • WiFi: 802.11bgn (2.4GHz), 802.11an/ac (5GHz)
  • Network: 5x Gigabit Ethernet ports
  • USB: 1x USB 2.0 ports
  • Power: 12V/1.5A via barrel

Flashing

Flashing OpenWrt

Target: ipq40xx
Subtarget: generic
Package architecture: arm_cortex-a7_neon-vfpv4
Supported Since Commit
Support started version: 23.05.0
Current supported version: 24.10.4
LAN Hardware: Qualcomm Atheros QCA8075
WLAN Hardware: Qualcomm Atheros IPQ4018
WLAN Comment: MIMO 2x2:2
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
git • >> 
ipq40xx: add support for Pakedge WR-1
Pakedge WR-1 is a dual-band wireless router.

Specification
SoC: Qualcomm Atheros IPQ4018
RAM: 256 MB DDR3
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 2T2R integrated
      5 GHz 2T2R integrated
Ethernet: 5x 10/100/1000 Mbps QCA8075
USB: 1x 2.0
LEDS: 8x (3 GPIO controlled, 5 connected to switch)
Buttons: 1x GPIO controlled
UART: pin header J5
      1. 3.3V, 2. GND, 3. TX, 4. RX
      baud: 115200, parity: none, flow control: none

Installation
1. Rename initramfs image to:
   openwrt-ipq806x-qcom-ipq40xx-ap.dk01.1-c1-fit-uImage-initramfs.itb
   and copy it to USB flash drive with FAT32 file system.
2. Connect USB flash drive to the router and apply power while pressing
   reset button. Hold the button, on the lates bootloader version, when
   Power and WiFi-5 LEDs will start blinking release it. For the older
   bootloader holding it for 15 seconds should suffice.
3. Now the router boots the initramfs image, at some point (close to one
   minute) the Power LED will start blinking, when stops, router is fully
   booted.
4. Connect to one of LAN ports and use SSH to open the shell at
   192.168.1.1.
5. ATTENTION! now backup the mtd8 and mtd9 partitions, it's necessary if,
   at some point, You want to go back to original firmware. The firmware
   provided by manufacturer on its site is encrypted and U-Boot accepts
   only decrypted factory images, so there's no way to restore original
   firmware.
6. If the backup is prepared, transfer the sysupgrade image to the router
   and use 'sysupgrade' command to flash it.
7. After successful flashing router will reboot. At some point the Power
   LED will start blinking, wait till it stops, then router is ready for
   configuration.

Additional information
U-Boot command line is password protected. Password is unknown.

Pictures

Retail Images
User Images
  • Board Top
    Board Top
  • Board Bottom
    Board Bottom
Retrieved from "https://techinfodepot.shoutwiki.com/w/index.php?title=Pakedge_WR-1&oldid=519919"