Panasonic N5HBZ0000055
From TechInfoDepot
Jump to navigationJump to searchabgn (AN300) | |||||
|---|---|---|---|---|---|
| Platform | |||||
| Brand • Model • Rev |
Panasonic N5HBZ0000055 | ||||
| Interface |
USB 2.0 | ||||
| Connector |
Male A | ||||
| Form factor |
dongle | ||||
ID:04da:3904 Windows: USB\VID_04DA&PID_3904 | |||||
| FCCID | |||||
| ICID | |||||
| Chipset |
Atheros AR9002U-2NX | ||||
| Chip1 |
Atheros AR7010 | ||||
| Chip2 |
Atheros AR9280 | ||||
| MIMO status |
1x2:2 | ||||
| Wireless Standards |
IEEE 802.11a/b/g/n | ||||
| 802.11n |
up to 150/150 Mbps | ||||
| 802.11g |
up to 54 Mbps | ||||
| 802.11b |
up to 11 Mbps | ||||
| Operating Frequency |
2.4 GHz | ||||
| Other | |||||
| Manuf/OEM/ODM | |||||
| UART |
has accessible UART | ||||
Probable Linux driver | |||||
Windows driver | |||||
| Retail | |||||
| FCC approval date | 02 December 2010 | ||||
| ASIN |
B00AK4L30C  | ||||
| |||||
For a list of all currently documented Atheros (QCA) chipsets with specifications, see Atheros.
For a list of all currently documented Panasonic device with specifications, see Panasonic.
Overview
This device may also be known as TY-WL20U.
Additional models of N5HBZ0000056 and N5HBZ0000057 noted within the WLU5080's test report.
Usage on Linux w/ ath9k_htc
This device works fine with ath9k_htc. At least some units (or probably most US distributed ones) have the following EEPROM settings...
- 0x6a RegDomain (World roaming, passive scan + no beaconing / IBSS on 5 GHz channels, see this relevant linux-wireless thread)
- 1x2 chain mask
Capable of Master / AP operation but because of the EEPROM world regulatory domain, it will not work as a Master / AP device in the 5GHz band on most platforms. The linux cfg80211 driver reports this condition as...
wlan0: IEEE 802.11 Configured channel (36) not found from the channel list of current mode (2) IEEE 802.11a wlan0: IEEE 802.11 Hardware does not support configured channel Could not select hw_mode and channel. (-4)
This can be circumvented, but it requires mucking with the regulatory framework in some fashion.
OpenWRT 'Barrier Breaker' since r32126 contains a fix that removes the "no IR/IBSS" condition on channels 36-48 only, permitting AP / Master mode on these channels. Tested to work on this device.
Pictures
- External
- Internal
board, main side, shielded (Strafe's unit)
board, main side, shielded
board, main side
board, opp. side
lower portion (AR7010)
middle portion (AR9280)
antenna closeup
Notes
dmesg dump
usb 3-2: new high-speed USB device number 7 using xhci_hcd usb 3-2: New USB device found, idVendor=04da, idProduct=3904 usb 3-2: New USB device strings: Mfr=16, Product=32, SerialNumber=48 usb 3-2: Product: UB94 usb 3-2: Manufacturer: ATHEROS usb 3-2: SerialNumber: 12345 usb 3-2: ath9k_htc: Firmware htc_7010.fw requested usb 3-2: ath9k_htc: Transferred FW: htc_7010.fw, size: 72992 ath9k_htc 3-2:1.0: ath9k_htc: HTC initialized with 45 credits ath9k_htc 3-2:1.0: ath9k_htc: FW Version: 1.3 ath: EEPROM regdomain: 0x6a ath: EEPROM indicates we should expect a direct regpair map ath: Country alpha2 being used: 00 ath: Regpair used: 0x6a ieee80211 phy5: Atheros AR9280 Rev:2
cat /sys/kernel/debug/ieee80211/phyX/ath9k_htc/base_eeprom
mTOR ath9k_htc # cat base_eeprom
Major Version : 14
Minor Version : 25
Checksum : 13353
Length : 3556
RegDomain1 : 106
RegDomain2 : 31
TX Mask : 1
RX Mask : 3
Allow 5GHz : 1
Allow 2GHz : 1
Disable 2GHz HT20 : 0
Disable 2GHz HT40 : 0
Disable 5Ghz HT20 : 0
Disable 5Ghz HT40 : 0
Big Endian : 0
Cal Bin Major Ver : 0
Cal Bin Minor Ver : 8
Cal Bin Build : 133
MacAddress : e0:ca:94:9f:f9:e5
cat /sys/kernel/debug/ieee80211/phyX/ath9k_htc/modal_eeprom
| hidden due to size |
|---|
mTOR ath9k_htc # cat modal_eeprom
2G 5G
==== ====
Chain0 Ant. Control : 16 | 16
Chain1 Ant. Control : 16 | 16
Chain2 Ant. Control : 0 | 0
Ant. Common Control : 528 | 528
Chain0 Ant. Gain : 0 | 0
Chain1 Ant. Gain : 0 | 0
Chain2 Ant. Gain : 0 | 0
Switch Settle : 45 | 44
Chain0 TxRxAtten : 32 | 32
Chain1 TxRxAtten : 32 | 32
Chain2 TxRxAtten : 11 | 11
Chain0 RxTxMargin : 0 | 0
Chain1 RxTxMargin : 0 | 0
Chain2 RxTxMargin : 16 | 11
ADC Desired size : 226 | 226
PGA Desired size : 0 | 0
Chain0 xlna Gain : 13 | 14
Chain1 xlna Gain : 13 | 14
Chain2 xlna Gain : 13 | 14
txEndToXpaOff : 0 | 0
txEndToRxOn : 2 | 2
txFrameToXpaOn : 14 | 14
CCA Threshold) : 28 | 28
Chain0 NF Threshold : 255 | 202
Chain1 NF Threshold : 255 | 202
Chain2 NF Threshold : 255 | 202
xpdGain : 3 | 3
External PD : 1 | 1
Chain0 I Coefficient : 0 | 0
Chain1 I Coefficient : 0 | 0
Chain2 I Coefficient : 0 | 0
Chain0 Q Coefficient : 0 | 0
Chain1 Q Coefficient : 0 | 0
Chain2 Q Coefficient : 0 | 0
pdGainOverlap : 6 | 6
Chain0 OutputBias : 3 | 1
Chain0 DriverBias : 3 | 1
xPA Bias Level : 2 | 0
2chain pwr decrease : 0 | 0
3chain pwr decrease : 0 | 0
txFrameToDataStart : 14 | 14
txFrameToPaOn : 14 | 14
HT40 Power Inc. : 2 | 2
Chain0 bswAtten : 26 | 22
Chain1 bswAtten : 26 | 22
Chain2 bswAtten : 0 | 0
Chain0 bswMargin : 20 | 31
Chain1 bswMargin : 20 | 31
Chain2 bswMargin : 0 | 0
HT40 Switch Settle : 45 | 44
Chain0 xatten2Db : 0 | 0
Chain1 xatten2Db : 0 | 0
Chain2 xatten2Db : 0 | 0
Chain0 xatten2Margin : 0 | 0
Chain1 xatten2Margin : 0 | 0
Chain2 xatten2Margin : 0 | 0
Chain1 OutputBias : 3 | 1
Chain1 DriverBias : 3 | 1
LNA Control : 29 | 29
XPA Bias Freq0 : 0 | 0
XPA Bias Freq1 : 0 | 0
XPA Bias Freq2 : 0 | 0
|
iw phy info
Wiphy phy0
Band 1:
Capabilities: 0x114e
HT20/HT40
SM Power Save disabled
RX HT40 SGI
RX STBC 1-stream
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT RX MCS rate indexes supported: 0-15
TX unequal modulation not supported
HT TX Max spatial streams: 1
HT TX MCS rate indexes supported may differ
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (20.0 dBm) (passive scanning)
* 2472 MHz [13] (20.0 dBm) (passive scanning)
* 2484 MHz [14] (disabled)
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Band 2:
Capabilities: 0x114e
HT20/HT40
SM Power Save disabled
RX HT40 SGI
RX STBC 1-stream
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT RX MCS rate indexes supported: 0-15
TX unequal modulation not supported
HT TX Max spatial streams: 1
HT TX MCS rate indexes supported may differ
Frequencies:
* 5180 MHz [36] (30.0 dBm) (passive scanning, no IBSS)
* 5200 MHz [40] (30.0 dBm) (passive scanning, no IBSS)
* 5220 MHz [44] (30.0 dBm) (passive scanning, no IBSS)
* 5240 MHz [48] (30.0 dBm) (passive scanning, no IBSS)
* 5260 MHz [52] (30.0 dBm) (passive scanning, no IBSS, radar detection)
* 5280 MHz [56] (30.0 dBm) (passive scanning, no IBSS, radar detection)
* 5300 MHz [60] (30.0 dBm) (passive scanning, no IBSS, radar detection)
* 5320 MHz [64] (30.0 dBm) (passive scanning, no IBSS, radar detection)
* 5500 MHz [100] (30.0 dBm) (passive scanning, no IBSS, radar detection)
* 5520 MHz [104] (30.0 dBm) (passive scanning, no IBSS, radar detection)
* 5540 MHz [108] (30.0 dBm) (passive scanning, no IBSS, radar detection)
* 5560 MHz [112] (30.0 dBm) (passive scanning, no IBSS, radar detection)
* 5580 MHz [116] (30.0 dBm) (passive scanning, no IBSS, radar detection)
* 5600 MHz [120] (30.0 dBm) (passive scanning, no IBSS, radar detection)
* 5620 MHz [124] (30.0 dBm) (passive scanning, no IBSS, radar detection)
* 5640 MHz [128] (30.0 dBm) (passive scanning, no IBSS, radar detection)
* 5660 MHz [132] (30.0 dBm) (passive scanning, no IBSS, radar detection)
* 5680 MHz [136] (30.0 dBm) (passive scanning, no IBSS, radar detection)
* 5700 MHz [140] (30.0 dBm) (passive scanning, no IBSS, radar detection)
* 5745 MHz [149] (30.0 dBm) (passive scanning, no IBSS)
* 5765 MHz [153] (30.0 dBm) (passive scanning, no IBSS)
* 5785 MHz [157] (30.0 dBm) (passive scanning, no IBSS)
* 5805 MHz [161] (30.0 dBm) (passive scanning, no IBSS)
* 5825 MHz [165] (30.0 dBm) (passive scanning, no IBSS)
Bitrates (non-HT):
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
Coverage class: 0 (up to 0m)
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP (00-0f-ac:4)
* CMAC (00-0f-ac:6)
Available Antennas: TX 0x1 RX 0x3
Configured Antennas: TX 0x1 RX 0x3
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* mesh point
* P2P-client
* P2P-GO
software interface modes (can always be added):
* AP/VLAN
* monitor
valid interface combinations:
* #{ managed, P2P-client } <= 2, #{ AP, mesh point, P2P-GO } <= 2,
total <= 2, #channels <= 1
Supported commands:
* new_interface
* set_interface
* new_key
* new_beacon
* new_station
* new_mpath
* set_mesh_params
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* remain_on_channel
* set_tx_bitrate_mask
* action
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* set_wds_peer
* Unknown command (84)
* Unknown command (87)
* Unknown command (85)
* Unknown command (89)
* Unknown command (92)
* testmode
* connect
* disconnect
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* Unknown mode (10): 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* Unknown mode (10): 0x40 0xd0
Device supports RSN-IBSS.
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
