Ruckus Wireless ZoneFlex 7343

bgn (N300)
ZoneFlex 7343 Access Point Indoor Single-Band 802.11n AP
Homepage	Product page 7341/3
WikiDevi.wi-cat.ru	Ruckus Wireless ZoneFlex 7343
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	Ruckus Wireless ZoneFlex 7343
FCC ID	S9GZF7343
IC ID	5912A-ZF7343
Type	access point
CPU1 Y	Atheros AR7161
CPU1 Type	MIPS 24K
CPU1 Speed	680 MHz
Flash1 Chip	Brand? Model?
Flash1 Size	16 MiB 16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> (SPI NOR)
RAM1 Size	64 MiB 67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br /> (DDR)
RAM1 Chip	Brand? Model? x 2
ETH chip1	Atheros AR7161
ETH chip2	Marvell 88E1116R
Switch	Realtek RTL8363S
Ethernet Port Count	1-1GbE-WAN 3-100MbE-LAN
Wired Standard	IEEE 802.3i/3u/3ab
802dot11 OUI: none specified
Stock bootloader	U-Boot
Expansion IF types	none specified
PoE	802.3af, standard
Power	12 VDC, 1 A
Connector type	barrel
Serial Port (UART)	yes, 3.3V TTL, (115200 8N1)
Other
Default IP address: 192.168.0.1 the IP 192.168.0.1 is used by 825 additional devices of which 17 are Ruckus Wireless devices Default login user: super Default login password: admin super:admin credentials used by 1 additional devices of which 1 are Ruckus Wireless devices
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Retail
FCC approval date	11 March 2010
Radio 1
Chip1	Atheros AR9280
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11b/g/n
802.11n	up to 300 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
FCC ID Ruckus Wireless ZoneFlex 7341 S9GZF7343

For a list of all currently documented Atheros (QCA) chipsets with specifications, see Atheros.
For a list of all currently documented Marvell chipsets with specifications, see Marvell.
For a list of all currently documented Realtek chipsets with specifications, see Realtek.

For a list of all currently documented Ruckus Wireless devices with specifications, see Ruckus Wireless.

• 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.) = N300 class

Overview

This appears to be a AR71xx+AR922x device.

10/100/1000 PoE port + 2x 10/100 ports

The Ruckus Wireless logo, "GD 11", and "220-11133[ ]Rev[ ] Ser." is silkscreened on the board.

"FAB 100-11133-001 REV 2" is on the opposite (component) side of the board.

Default credentials are per the FCC label.

Per the FCC manual, the default SSID format is WirelessX (where X is a number).

Links of Interest

• On SpeedGuide.net
• 7300 series Datasheet

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)

Target: ath79
Subtarget: generic
Package architecture: mips_24kc
Supported Since Commit
Support started version: 23.05.0
Current supported version: 25.12.1

LAN Hardware: Realtek RTL8363S
WLAN Hardware: Atheros AR9280
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
Comment:
sysupgrade image = factory image;

git • >>

ath79: support Ruckus ZoneFlex 7341/7343/7363 Ruckus ZoneFlex 7363 is a dual-band, dual-radio 802.11n 2x2 MIMO enterprise access point. ZoneFlex 7343 is the single band variant of 7363 restricted to 2.4GHz, and ZoneFlex 7341 is 7343 minus two Fast Ethernet ports. Hardware highligts: - CPU: Atheros AR7161 SoC at 680 MHz - RAM: 64MB DDR - Flash: 16MB SPI-NOR - Wi-Fi 2.4GHz: AR9280 PCI 2x2 MIMO radio with external beamforming - Wi-Fi 5GHz: AR9280 PCI 2x2 MIMO radio with external beamforming - Ethernet 1: single Gigabit Ethernet port through Marvell 88E1116R gigabit PHY - Ethernet 2: two Fast Ethernet ports through Realtek RTL8363S switch, connected with Fast Ethernet link to CPU. - PoE: input through Gigabit port - Standalone 12V/1A power input - USB: optional single USB 2.0 host port on the -U variants. Serial console: 115200-8-N-1 on internal H1 header. Pinout: H1 ---------- |1|x3|4|5| ---------- Pin 1 is near the "H1" marking. 1 - RX x - no pin 3 - VCC (3.3V) 4 - GND 5 - TX Installation: - Using serial console - requires some disassembly, 3.3V USB-Serial adapter, TFTP server, and removing a single PH1 screw. 0. Connect serial console to H1 header. Ensure the serial converter does not back-power the board, otherwise it will fail to boot. 1. Power-on the board. Then quickly connect serial converter to PC and hit Ctrl+C in the terminal to break boot sequence. If you're lucky, you'll enter U-boot shell. Then skip to point 3. Connection parameters are 115200-8-N-1. 2. Allow the board to boot. Press the reset button, so the board reboots into U-boot again and go back to point 1. 3. Set the "bootcmd" variable to disable the dual-boot feature of the system and ensure that uImage is loaded. This is critical step, and needs to be done only on initial installation. > setenv bootcmd "bootm 0xbf040000" > saveenv 4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed. Use the Gigabit interface, Fast Ethernet ports are not supported under U-boot: > setenv serverip 192.168.1.2 > setenv ipaddr 192.168.1.1 > tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7363-initramfs-kernel.bin > bootm 0x81000000 5. Optional, but highly recommended: back up contents of "firmware" partition: $ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7363_fw_backup.bin 6. Copy over sysupgrade image, and perform actual installation. OpenWrt shall boot from flash afterwards: $ ssh root@192.168.1.1 # sysupgrade -n openwrt-ath79-generic-ruckus_zf7363-squashfs-sysupgrade.bin After unit boots, it should be available at the usual 192.168.1.1/24. Return to factory firmware: 1. Copy over the backup to /tmp, for example using scp 2. Unset the "bootcmd" variable: fw_setenv bootcmd "" 3. Use sysupgrade with force to restore the backup: sysupgrade -F ruckus_zf7363_backup.bin 4. System will reboot. Quirks and known issues: - Fast Ethernet ports on ZF7363 and ZF7343 are supported, but management features of the RTL8363S switch aren't implemented yet, though the switch is visible over MDIO0 bus. This is a gigabit-capable switch, so link establishment with a gigabit link partner may take a longer time because RTL8363S advertises gigabit, and the port magnetics don't support it, so a downshift needs to occur. Both ports are accessible at eth1 interface, which - strangely - runs only at 100Mbps itself. - Flash layout is changed from the factory, to use both firmware image partitions for storage using mtd-concat, and uImage format is used to actually boot the system, which rules out the dual-boot capability. - Both radio has its own EEPROM on board, not connected to CPU. - The stock firmware has dual-boot capability, which is not supported in OpenWrt by choice. It is controlled by data in the top 64kB of RAM which is unmapped, to avoid the interference in the boot process and accidental switch to the inactive image, although boot script presence in form of "bootcmd" variable should prevent this entirely. - On some versions of stock firmware, it is possible to obtain root shell, however not much is available in terms of debugging facitilies. 1. Login to the rkscli 2. Execute hidden command "Ruckus" 3. Copy and paste ";/bin/sh;" including quotes. This is required only once, the payload will be stored in writable filesystem. 4. Execute hidden command "!v54!". Press Enter leaving empty reply for "What's your chow?" prompt. 5. Busybox shell shall open. Source: https://alephsecurity.com/vulns/aleph-2019014 - There is second method to achieve root shell, using command injection in the web interface: 1. Login to web administration interface 2. Go to Administration > Diagnostics 3. Enter |telnetd${IFS}-p${IFS}204${IFS}-l${IFS}/bin/sh into "ping" field 4. Press "Run test" 5. Telnet to the device IP at port 204 6. Busybox shell shall open. Source: https://github.com/chk-jxcn/ruckusremoteshell