SerComm H500-s vfes
| abgn+ac (AC2100) | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| wireless router, dsl modem, CPE | |||||||||||||
|
| |||||||||||||
| WikiDevi.wi-cat.ru | SerComm H500-s | ||||||||||||
| 3rd Party Firmware | |||||||||||||
| dd-wrt | Status Unknown | ||||||||||||
| OpenWrt | Partial Support | ||||||||||||
| Tomato any flavor | Status Unknown | ||||||||||||
| Gargoyle | Status Unknown | ||||||||||||
| Platform | |||||||||||||
| Brand • Model • Rev | SerComm H500-s v1 (Vodafone) | ||||||||||||
| FCC ID (fcc.io) | none specified | ||||||||||||
| FCC ID (fcc.report) | none specified | ||||||||||||
| Board ID | BXK00C-1.6 | ||||||||||||
| Type | wireless router, dsl modem, CPE | ||||||||||||
| CPU1 | Broadcom BCM63167 | ||||||||||||
| CPU1 Type | MIPS BMIPS4350 | ||||||||||||
| CPU1 Speed | 400 MHz ( 2 cores ) | ||||||||||||
| CPU2 | Quantenna QT3740BC | ||||||||||||
| CPU2 Type | ARC 700 | ||||||||||||
| CPU2 Speed | 500 MHz ( 2 cores ) | ||||||||||||
| Flash1 Chip | Macronix MX30LF1G18AC-TI | ||||||||||||
| Flash1 Size | 128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> | ||||||||||||
| Flash2 Chip | Macronix MX25L512E | ||||||||||||
| Flash2 Size | 0.064 MiB67,108.864 B <br />524.288 Kib <br />65.536 KiB <br />0.512 Mib <br />6.25e-5 GiB <br /> | ||||||||||||
| RAM1 Size | 128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> | ||||||||||||
| RAM1 Chip | Nanya NT5CC64M16GP-DI | ||||||||||||
| RAM2 Size | 128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> | ||||||||||||
| RAM2 Chip | Nanya NT5CC64M16GP-DI | ||||||||||||
| ETH chip1 | Broadcom BCM63167 | ||||||||||||
| Switch | Broadcom BCM53134S | ||||||||||||
| Ethernet Port Count | 4-1GbE-LAN | ||||||||||||
| Wired Standard | IEEE 802.3i/3u/3ab | ||||||||||||
| Stock bootloader | CFE | ||||||||||||
| Stock FW OS | Linux | ||||||||||||
| Expansion IF types | USB 2.0 | ||||||||||||
| USB ports | 1 | ||||||||||||
| USB Hub Compatible | Untested | ||||||||||||
| Power | 12 VDC, 2.5 A | ||||||||||||
| Connector type |
barrel 5.5 mm (OD) 2.5 mm (ID) | ||||||||||||
| Serial Port (UART) | yes, 4-pin header, 3.3V TTL, (115200 8N1) | ||||||||||||
|
Flags: | |||||||||||||
|
Additional chips | |||||||||||||
| Other | |||||||||||||
|
Default SSID: vodafoneXXXX | |||||||||||||
| Manuf/OEM/ODM | SerComm | ||||||||||||
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) | ||||||||||||
| Retail | |||||||||||||
| Availability | Vodafone | ||||||||||||
| (Est.) release date | January 2017 | ||||||||||||
| EAN |
8430208012420 (UPC DB, On eBay) | ||||||||||||
| Country of manuf | China | ||||||||||||
| Radio 1 | |||||||||||||
| Chip1 | Broadcom BCM63168 | ||||||||||||
| Wireless interface OUI | 78:81:02 | ||||||||||||
| Antenna Connector Type | U.FL | ||||||||||||
| MIMO status | 2x2:2 | ||||||||||||
| Wireless Standard | IEEE 802.11b/g/n | ||||||||||||
| 802.11n | up to 300 Mbps | ||||||||||||
| 802.11g | up to 54 Mbps | ||||||||||||
| 802.11b | up to 11 Mbps | ||||||||||||
| WiFi Operating Frequency | 2.4 GHz | ||||||||||||
| Radio 2 | |||||||||||||
| Chip1 | Quantenna QT3740BC | ||||||||||||
| Chip2 | Quantenna QT2518B | ||||||||||||
| Wireless interface OUI | 78:81:02 | ||||||||||||
| Antenna Connector Type | MS156 | ||||||||||||
| MIMO status | 4x4:4 | ||||||||||||
| Wireless Standard | IEEE 802.11a/n/ac | ||||||||||||
| 802.11ac | up to 1733 Mbps | ||||||||||||
| 802.11n | up to 600 Mbps | ||||||||||||
| 802.11a | up to 54 Mbps | ||||||||||||
| WiFi Operating Frequency | 5 GHz | ||||||||||||
| |||||||||||||
For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.
For a list of all currently documented Quantenna chipsets with specifications, see Quantenna.
For a list of all currently documented SerComm devices with specifications, see SerComm.
Overview
- Model Name: Vodafone H500-s (SerComm)
"BXK00C-1.6" and "1735" is silkscreened on the board.
Specifications
- Flash: Macronix MX25L512E 64KB (Serial NOR)
- 512Kbit (x1/x2) 3V CMOS Flash Memory
- Macronix MX30LF1G18AC 128MB (SLC NAND)
- 1Gbit x8 4-bit ECC 48-pin TSOP 3V SLC Flash
- RAM: Nanya NT5CC64M16GP 128MB (DDR3L)
- 1Gbit 64Mx16 1.35V 96-Pin VFBGA SDRAM
- PSU: PS30W120EUG20-BXK-00
Wi-Fi CERTIFIED N
- 2.4 GHz, 5 GHz - Concurrent
- 2 Spatial Streams 2.4 GHz
- 3 Spatial Streams 5 GHz
- Short Guard Interval
- TX A-MPDU
- STBC Transmit
- 40 MHz operation in 2.4 GHz, with coexistence mechanisms
- 40 MHz operation in 5 GHz
- HT Duplicate Mode (MCS 32)
Wi-Fi CERTIFIED AC
- 4 Spatial Streams 5 GHz
- Rx MCS 8-9 (256-QAM)
- Rx A-MPDU of A-MSDU
- Tx SU beamformer
- Low Density Parity Check coding
Links of Interest
Source code
Flashing
| NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
| Devices with Broadcom WiFi chipsets have limited OpenWrt supportability (due to limited FLOSS driver availability for Broadcom chips). Consider this when choosing a device to buy, or when deciding to flash OpenWrt on your device because it is listed as supported. See Broadcom WiFi for details. |
| DSL will not work at all on devices with BCM63xx DSL chipset (due to unavailability of FLOSS driver for Broadcom chips). Consider this when choosing a device to buy, or when deciding to flash OpenWrt on your device because it is listed as supported. See Broadcom DSL, Unsupported: DSL modem and Broadcom BCM63xx for details. |
Subtarget: bcm63268
Package architecture: mips_mips32
Supported Since Commit
Support started version: 21.02.0
Current supported version: 25.12.0
DSL modem, FXS, WiFi 2.4GHz
LAN Hardware: Broadcom BCM53134S
WLAN Hardware: Broadcom BCM435f, Quantenna QT3740BC
Installation method(s):
GUI OEM
Recovery method(s):
CFE TFTP recovery, CFE TFTP + serial recovery, CFE web recovery
| git • >> |
|---|
bcm63xx: add support for the Sercomm H500-s
Sercomm H500-s is an xDSL dual band wireless router based on Broadcom
BCM63167 SoC.
Hardware:
SoC: Broadcom BCM63167
CPU: BMIPS4350 V8.0, 400 MHz, 2 cores
Flash: NAND 128 MiB
RAM: DDR3 128 MiB
Ethernet: 4x 10/100/1000 Mbps
Switch: BCM53134S
Wireless: 802.11b/g/n: BCM435f (integrated)
802.11ac: Quantenna QT3740BC (onboard SoC)
USB: 1x 2.0
LEDs/Buttons: 11x / 2x
Flash instruction, web UI:
1. Reset to defaults using the reset button if the admin password is
unknown
2. Login into the web UI as admin.
Address: http://192.168.0.1
User: admin
Password: VF-ESVodafone-H-500-s or l033i-h500s
3. Go to Settings -> Firmware Update, and select the Openwrt factory
firmware
4. Update the firmware.
5. Wait until it finish, the device will reboot with Openwrt installed
on the alternative image partitions keeping the stock firmware in
the former.
Notes:
- The patch also adds support for the lowi version. Only the factory
firmware is different.
- The integrated Wifi in the Broadcom Soc isn't still supported.
- The Quantenna 802.11ac wifi works ok, but needs to be configured with
the Quantenna client application. It can't be configured with Luci
nor any iw command since it's a separated subsystem linked via
ethernet.
- The BCM53134S external switch is managed via MDIO which isn't
supported in this target. Therefore it will behave as a dumb switch.
|
JTAG-Serial Info
Serial
Serial Pinouts
- baudrate: 115200
| GND | TX | VCC | RX |
| ■ | ■ | ■ | ■ |
|---|---|---|---|
| ▷ 1 | 2 | 3 | 4 |
Boot log
| boot log • >> |
|---|
HELO
CPUI
L1CI
HELO
CPUI
L1CI
4.1605-1.0.38-118.3
DRAM
----
PHYS
STRF
400H
PHYE
DDR3
SIZ4
SIZ3
SIZ2
DINT
USYN
LSYN
MFAS
LMBE
RACE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN
FPS0
FDPM
PMOK
GFOK
F002
F001
RAM1
NAN9
NAN3
RFS0
NAN5
Base: 4.16_05
CFE version 1.0.38-118.3 for BCM963268 (32bit,SP,BE)
Build Date: Fri Aug 19 13:10:18 CST 2016 (jeremy@Ubuntu)
Copyright (C) 2000-2015 Broadcom Corporation.
Boot Strap Register: 0x1ff90bf
Chip ID: BCM63167D0, MIPS: 400MHz, DDR: 400MHz, Bus: 200MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 134217728 bytes (128MB)
Boot Address: 0xb8000000
NAND ECC BCH-4, page size 0x800 bytes, spare size used 64 bytes
NAND flash device: MXIC MX30LF1G08AA, id 0xc2f1 block 128KB size 131072KB
GPIOOverlays is 0x8010
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host/tftp (f/h/c) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Default host ramdisk file name :
Default ramdisk store address :
Board Id (0-33) : 963167REF3
Number of MAC Addresses (1-32) : 16
Base MAC Address : 78:81:02:61:DE:AD
PSI Size (1-128) KBytes : 24
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Auxillary File System Size Percent: 0
Main Thread Number [0|1] : 0
WLan Feature : 0x00
Voice Board Configuration (0-19) : LE9672_ZSI
Partition 1 Size (MB) :
Partition 2 Size (MB) :
Partition 3 Size (MB) :
Partition 4 Size (MB) (Data) : 4MB
External switch id = a750
SC_DEBUG: Nand Partition Table Magic Found at 20000.
part 0, logic_offset 00000000, logic_length 00020000, real_offset 00000000, real_length 00020000
part 1, logic_offset 00020000, logic_length 000a0000, real_offset 00020000, real_length 000a0000
part 2, logic_offset 000c0000, logic_length 00140000, real_offset 000c0000, real_length 00140000
part 3, logic_offset 00200000, logic_length 00140000, real_offset 00200000, real_length 00140000
part 4, logic_offset 00340000, logic_length 000a0000, real_offset 00340000, real_length 000a0000
part 5, logic_offset 003e0000, logic_length 00140000, real_offset 003e0000, real_length 00140000
part 6, logic_offset 00520000, logic_length 01e00000, real_offset 00520000, real_length 01e00000
part 7, logic_offset 02320000, logic_length 01400000, real_offset 02320000, real_length 01400000
part 8, logic_offset 03720000, logic_length 01e00000, real_offset 03720000, real_length 01e00000
part 9, logic_offset 05520000, logic_length 01400000, real_offset 05520000, real_length 01400000
part 10, logic_offset 06920000, logic_length 00140000, real_offset 06920000, real_length 00140000
part 11, logic_offset 06a60000, logic_length 00140000, real_offset 06a60000, real_length 00140000
part 12, logic_offset 06ba0000, logic_length 00280000, real_offset 06ba0000, real_length 00280000
part 13, logic_offset 06e20000, logic_length 00280000, real_offset 06e20000, real_length 00280000
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
***************************************************
Sercomm Boot Version 0.0.4.0
***************************************************
Entering Firmware : Everything is OK.
Boot Flag's Magic Found at 6920000.
Boot Flag's Magic Found at 6a60000.
Find bootFlag successfully.
BootFlag1: eRcOmM.002
BootFlag2: eRcOmM.001
Booting from first image (0xb8520000) ...
Checksum ... OK!
Correctable ECC Error detected: addr=0x0052aa00, intrCtrl=0x00000090, accessCtrl=0xE3441010
Correctable ECC Error detected: addr=0x0052aa00, intrCtrl=0x00000090, accessCtrl=0xE3441010
Correctable ECC Error detected: addr=0x005f9000, intrCtrl=0x000000B0, accessCtrl=0xE3441010
Decompression LZMA Image OK!
Entry at 0x80455f10
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
1 buffers found
Closing DMA Channels
Starting program at 0x80455f10
Linux version 3.4.11-rt19 (west@ubuntu) (gcc version 4.6.2 (Buildroot 2011.11) ) #3 SMP PREEMPT Thu May 31 16:56:36 CST 2018
963167REF3 prom init
CPU revision is: 0002a080 (Broadcom BMIPS4350)
DSL SDRAM reserved: 0x132000
Determined physical RAM map:
memory: 07ece000 @ 00000000 (usable)
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00007ece
Movable zone start PFN for each node
Early memory PFN ranges
0: 0x00000000 -> 0x00007ece
On node 0 totalpages: 32462
free_area_init_node: node 0, pgdat 8056e6d0, node_mem_map 81000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 222 pages used for memmap
Normal zone: 28144 pages, LIFO batch:7
PERCPU: Embedded 7 pages/cpu @81103000 s5520 r8192 d14960 u32768
pcpu-alloc: s5520 r8192 d14960 u32768 alloc=8*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32208
Kernel command line: root=mtd:rootfs rw rootfstype=jffs2 irqaffinity=0
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Memory: 122632k/129848k available (4432k kernel code, 7216k reserved, 1068k data, 220k init, 0k highmem)
Preemptible hierarchical RCU implementation.
NR_IRQS:128
console [ttyS0] enabled
Allocating memory for DSP module core and initialization code
Allocated DSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0
Calibrating delay loop... 397.31 BogoMIPS (lpj=198656)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
--Kernel Config--
SMP=1
PREEMPT=1
DEBUG_SPINLOCK=0
DEBUG_MUTEXES=0
Broadcom Logger v0.1 May 31 2018 16:03:32
CPU revision is: 0002a080 (Broadcom BMIPS4350)
Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Brought up 2 CPUs
NET: Registered protocol family 16
Internal 1P2 VREG will be shutdown if unused...Unused, turn it off (0000845b-00008457=4<300)
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0xa0f00000-0xa0ffffff]
pci_bus 0000:00: root bus resource [io 0xa2000000-0xa200ffff]
pci 0000:00:00.0: [14e4:435f] type 00 class 0x028000
pci 0000:00:00.0: reg 10: [mem 0x10004000-0x10005fff]
pci 0000:00:09.0: [14e4:6300] type 00 class 0x0c0310
pci 0000:00:09.0: reg 10: [mem 0x10002600-0x100026ff]
pci 0000:00:0a.0: [14e4:6300] type 00 class 0x0c0320
pci 0000:00:0a.0: reg 10: [mem 0x10002500-0x100025ff]
PCI host bridge to bus 0000:01
pci_bus 0000:01: root bus resource [mem 0x11000000-0x11efffff]
pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
pci 0000:01:00.0: [14e4:6326] type 01 class 0x060400
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:01:00.0: PCI bridge to [bus 02-02]
bcmhs_spi bcmhs_spi.1: master is unqueued, this is deprecated
bcmleg_spi bcmleg_spi.0: master is unqueued, this is deprecated
skb_free_task created successfully
gbpm_do_work scheduled
BLOG v3.0 Initialized
BLOG Rule v1.0 Initialized
Broadcom IQoS v0.1 May 31 2018 16:10:05 initialized
Broadcom GBPM v0.1 May 31 2018 16:10:05 initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP: reno registered
UDP hash table entries: 128 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
NET: Registered protocol family 1
PCI: CLS mismatch (64 != 16), using 16 bytes
bcm_tstamp initialized, (hpt_freq=200000000 2us_div=200 2ns_mult=5 2ns_shift=0)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
NTFS driver 2.1.30 [Flags: R/W].
jffs2: version 2.2. (NAND) (SUMMARY) �� 2001-2006 Red Hat, Inc.
fuse init (API version 7.18)
msgmni has been set to 239
io scheduler noop registered (default)
Broadcom NAND controller (BrcmNand Controller)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000000
B4: NandSelect=40000001, nandConfig=15142200, chipSelect=0
brcmnand_read_id: CS0: dev_id=c2f18095
After: NandSelect=40000001, nandConfig=15142200
DevId c2f18095 may not be supported. Will use config info
Spare Area Size = 16B/512B
Block size=00020000, erase shift=17
NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
ECC level changed to 4
OOB size changed to 16
BrcmNAND mfg 0 0 UNSUPPORTED NAND CHIP 128MB on CS0
Found NAND on CS0: ACC=e3441010, cfg=15142200, flashId=c2f18095, tim1=6532845b, tim2=00001e94
BrcmNAND version = 0x0400 128MB @00000000
brcmnand_scan: B4 nand_select = 40000001
brcmnand_scan: After nand_select = 40000001
handle_acc_control: default CORR ERR threshold 1 bits
ACC: 16 OOB bytes per 512B ECC step; from ID probe: 16
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 4.0 NAND flash size 128MB @18000000
ECC layout=brcmnand_oob_bch4_2k
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=35, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=4, eccbytes=7
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_slc_bch4_main_descr
Bad block table Bbt0 found at page 0000ffc0, version 0x01 for chip on CS0
Bad block table 1tbB found at page 0000ff80, version 0x01 for chip on CS0
brcmnand_reset_corr_threshold: default CORR ERR threshold 1 bits for CS0
brcmnand_reset_corr_threshold: CORR ERR threshold changed to 3 bits for CS0
brcmnandCET: Status -> Deferred
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: setting latency timer to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
ehci_hcd 0000:00:0a.0: irq 18, io mem 0x10002500
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: setting latency timer to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 17, io mem 0x10002600
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
DYING GASP IRQ Initialized and Enabled
Serial: BCM63XX driver $Revision: 3.00 $
Magic SysRq with Auxilliary trigger char enabled (type ^ h for list of supported commands)
ttyS0 at MMIO 0xb0000180 (irq = 13) is a BCM63XX
ttyS1 at MMIO 0xb00001a0 (irq = 42) is a BCM63XX
Total # RxBds=1448
bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized
bcmPktDma_init: Broadcom Packet DMA Library initialized
IPSEC SPU: SUCCEEDED
GACT probability NOT on
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1916 buckets, 7664 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP: cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_tcpmss registered
ebt_ftos registered
ebt_wmm_mark registered
8021q: 802.1Q VLAN Support v1.8
hub 1-0:1.0: over-current condition on port 2
VFS: Mounted root (jffs2 filesystem) readonly on device 31:6.
Freeing unused kernel memory: 220k freed
init started: BusyBox v1.15.3 ()
starting pid 296, tty '': '/etc/rcS'
bcm_ingqos: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Broadcom Ingress QoS Module Char Driver v0.1 May 31 2018 16:06:16 Registered<243>
Broadcom Ingress QoS ver 0.1 initialized
BPM: tot_mem_size=134217728B (128MB), buf_mem_size <15%> =20132655B (19MB), num of buffers=9986, buf size=2016
Broadcom BPM Module Char Driver v0.1 May 31 2018 16:05:56 Registered<244>
bcmxtmrt: Broadcom BCM3167D0 ATM/PTM Network Device v0.9 May 31 2018 16:08:15
NBUFF v1.0 Initialized
Initialized fcache state
Broadcom Packet Flow Cache Char Driver v3.0 May 31 2018 16:06:16 Registered<242>
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Broadcom Packet Flow Cache learning via BLOG enabled.
[FHW] pktDbgLvl[0x85d5f040]=0
[FHW] fhw_construct:
Initialized Fcache HW accelerator layer state
flwStatsThread created
Constructed Broadcom Packet Flow Cache v3.0 May 31 2018 16:06:16
chipId 0x631670D0
Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 May 31 2018 16:06:00 Registered <241>
Enabling SMISBUS PHYS_FAP_BASE[0] is 0x10c01000
FAP Soft Reset Done
4ke Reset Done
Enabling SMISBUS PHYS_FAP_BASE[1] is 0x10c01000
FAP Soft Reset Done
4ke Reset Done
FAP Debug values at 0xa5f246f0 0xa5fa46f0
fapGso_LoopBkThread created successfully
Allocated FAP0 SWQ_HOST2FAP_GSO_LOOPBACK_Q mem=a7998000 : 16384 bytes
Allocated FAP0 SWQ_FAP2HOST_GSO_LOOPBACK_Q mem=a7aa0000 : 16384 bytes
GSO LOOPBACK Cached HOST2FAP Q INFO:
Swq =b0825ef8 qStart=a7998000 qEnd=a799c000 msgSize=4 dqm=18 fapId=0
GSO LOOPBACK Cached FAP2HOST Q INFO:
Swq =b0825ec8 qStart=a7aa0000 qEnd=a7aa4000 msgSize=2 dqm=19 fapId=0
Allocated FAP0 SWQ_FAP2HOST_WFD_Q mem=a5df4000 : 7200 bytes
Allocated FAP1 SWQ_FAP2HOST_WFD_Q mem=a5cfc000 : 7200 bytes
Allocated FAP0 SWQ_FAP2HOST_WFD_Q mem=a5cfa000 : 7200 bytes
Allocated FAP1 SWQ_FAP2HOST_WFD_Q mem=a5efc000 : 7200 bytes
Allocated FAP0 TM SDRAM Queue Storage (a5f35780) : 390144 bytes @ a5400000
Allocated FAP1 TM SDRAM Queue Storage (a5fb5780) : 390144 bytes @ a5480000
[NTC fapProto] fapReset : Reset FAP Protocol layer
[FAP0] DSPRAM : stack <0x80000000><1792>, global <0x80000700><4568>, free <1832>, total<8192>
[FAP1] DSPRAM : stack <0x80000000><1792>, global <0x80000700><4568>, free <1832>, total<8192>
[FAP0] PSM : addr<0x80002000>, used <24472>, free <104>, total <24576>
[FAP1] PSM : addr<0x80002000>, used <24472>, free <104>, total <24576>
[FAP0] DQM : availableMemory 14668 bytes, nextByteAddress 0xE00048B0
[FAP1] DQM : availableMemory 14668 bytes, nextByteAddress 0xE00048B0
[FAP0] Initializing FAP4KE GSO LOOPBACK on fapIdx=0 ...
[FAP1] IC Timer started
[FAP0] SWQ: HOST2FAP_GSO_LOOPBACK
[FAP1] FAP4KE WFD Init Done...
[FAP0] >>>>------------------
[FAP0] swq =80007ef8 msgSize =4 words , maxDepth=1024
[FAP0] qStart =a7998000 qEnd=a799c000
[FAP0] rdPtr =a7998000 wrPtr=a7998000 count=0
[FAP0] swq->interrupts 0 processed =0 dropped =0
[FAP0] Associated DQM=18 dir HOST2FAP
[FAP0] ------------------<<<<
[FAP0] SWQ: FAP2HOST_GSO_LOOPBACK
[FAP0] >>>>------------------
[FAP0] swq =80007ec8 msgSize =2 words , maxDepth=2048
[FAP0] qStart =a7aa0000 qEnd=a7aa4000
[FAP0] rdPtr =a7aa0000 wrPtr=a7aa0000 count=0
[FAP0] swq->interrupts 0 processed =0 dropped =0
[FAP0] Associated DQM=19 dir FAP2HOST
[FAP0] ------------------<<<<
[FAP0] FAP4KE GSO LOOPBACK Init Done...
[FAP0] IC Timer started
[FAP0] FAP4KE WFD Init Done...
[FAP1] FAP BPM Initialized.
[FAP0] FAP BPM Initialized.
Broadcom Packet Flow Cache HW acceleration enabled.
fapDrv_construct: FAP0: pManagedMemory=b0820650. wastage 8 bytes
fapDrv_construct: FAP1: pManagedMemory=b0a20650. wastage 8 bytes
bcmPktDma_bind: FAP Driver binding successfull
[FAP0] FAP TM: ON
[FAP1] FAP TM: ON
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCM63167D0 Ethernet Network Device v0.1 May 31 2018 16:07:57
Broadcom GMAC Char Driver v0.1 May 31 2018 16:08:11 Registered<249>
Broadcom GMAC Driver v0.1 May 31 2018 16:08:11 Initialized
fapDrv_psmAlloc: fapIdx=1, size: 4800, offset=b0a20650 bytes remaining 7000
ETH Init: Ch:0 - 200 tx BDs at 0xb0a20650
fapDrv_psmAlloc: fapIdx=0, size: 4800, offset=b0820650 bytes remaining 7000
ETH Init: Ch:1 - 200 tx BDs at 0xb0820650
fapDrv_psmAlloc: wastage 8 bytes
fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b0821910 bytes remaining 2184
ETH Init: Ch:0 - 600 rx BDs at 0xb0821910
[FAP0] enetRxChannel 0
fapDrv_psmAlloc: wastage 8 bytes
fapDrv_psmAlloc: fapIdx=1, size: 4808, offset=b0a21910 bytes remaining 2184
ETH Init: Ch:1 - 600 rx BDs at 0xb0a21910
[FAP1] enetRxChannel 1
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
eth0: <Ext sw port: 1> <Logical : 09> PHY_ID <0x20180001 : 0x01> MAC : 78:81:02:61:DE:AD
eth1: <Ext sw port: 2> <Logical : 10> PHY_ID <0x20180002 : 0x02> MAC : 78:81:02:61:DE:AD
eth2: <Ext sw port: 3> <Logical : 11> PHY_ID <0x20180003 : 0x03> MAC : 78:81:02:61:DE:AD
eth3: <Ext sw port: 5> <Logical : 13> PHY_ID <0x22600e00 : 0x00> MAC : 78:81:02:61:DE:AD
eth4: <Int sw port: 3> <Logical : 03> PHY_ID <0x0010000c : 0x0c> MAC : 78:81:02:61:DE:AD
Ethernet Auto Power Down and Sleep: Enabled
All Port Bit Map: 0x2e08: eth4,eth0,eth1,eth2,eth3
Chip WAN Only Ports 0000, Defined WAN Only Ports 0000, WAN Only Port Result: 0x0000:
Chip WAN Preffered Ports 0008, Defined WAN Preffered Ports 0000, WAN Preffered Port Result: 0x0008:eth4
Chip LAN Only Ports 0000, Defined LAN Only Ports 0000, LAN Only Port Result: 0x0000:
WAN/LAN Both Capable Ports 0x2e00:eth0,eth1,eth2,eth3
[NTC arl] arlEnable : Enabled ARL binding to FAP
Broadcom Address Resolution Logic Processor (ARL) Char Driver v0.1 May 31 2018 16:05:56 Registered <245>
Broadcom 802.1Q VLAN Interface, v0.1
PCIe: No device found - Powering down
Endpoint: endpoint_init entry
Endpoint: endpoint_init COMPLETED
Initializing WLCSM Module
WLCSM Module loaded successfully
Wifi Forwarding Driver is initialized!
gre: GRE over IPv4 demultiplexor driver
ip_gre: GRE over IPv4 tunneling driver
PPTP driver version 0.8.5
Loading PCM shim driver
insmod: can't insert '/lib/modules/qwerpe.ko': No such file or directory
--SMP support
wl: dsl_tx_pkt_flush_len=338
wl: norm_wmark_tot=3552, pktc_wmark_tot=3552
wl 0000:00:00.0: setting latency timer to 64
wl: passivemode=1
wl0: creating kthread wl0-kthrd
wl: napimode=0
Neither SPROM nor OTP has valid image
wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
wl: ID=sb/0/
wl: ID=sb/0/
wl: loading /etc/wlan/bcm6362_map.bin
srom rev:8
wl0: allocskbmode=1 currallocskbsz=1024
wfd_bind: Dev wl%d wfd_idx 0 wl_radio_idx 0 Type skb configured WFD thread wfd0-thrd minQId/maxQId (20/1073741844), status (0) qmask 0x3
Instantiating WFD 0 thread
+++++ Added gso loopback support for dev=wl0 <84ce4800>
wfd_registerdevice Successfully registered dev wl0 ifidx 0 wfd_idx 0
wl0: Broadcom BCM435f 802.11 Wireless Controller 7.14.164.307.cpe4.16L05.1-kdb
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
Success
Note: Loading 6300 MDK (default) driver for 63167 chip
Note: Forcing 53115 driver for 53134
Switch MDK: num_switches = 2
Switch MDK: unit = 0; phy_pbmp = 0x8; config_pbmp = 0x18
Switch MDK: unit = 1; phy_pbmp = 0xe; config_pbmp = 0x2e
Switch MDK link poll thread: unit=0; phypbmp=0x8 config_pbmp=0x18
Switch MDK link poll thread: unit=1; phypbmp=0xe config_pbmp=0x2e
Energy Efficient Ethernet: Enabled
eth3 (Ext switch port: 5) (Logical Port: 13) Link UP 1000 mbps full duplex
[LAN] LAN5 Link UP 1000 mbps full duplex
device eth3 entered promiscuous mode
br0: port 1(eth3) entered forwarding state
br0: port 1(eth3) entered forwarding state
device eth3.10 entered promiscuous mode
br10: port 1(eth3.10) entered forwarding state
br10: port 1(eth3.10) entered forwarding state
Vodafone-H-500-s-v3.4.17
br0: port 1(eth3) entered forwarding state
Thu May 31 17:00:50 UTC 2018
ap_name=syslogd, action=start
ap_name=coredump, action=start
ap_name=energy_saving, action=start
ap_name=dnsmasq, action=start
ap_name=phy, action=start
device eth3 is already a member of a bridge; can't enslave it to bridge br0.
ap_name=dhcpd, action=create
Success
Success
Success
Success
ap_name=lanip, action=start
ap_name=firewall, action=start
ap_name=telnetd, action=start
ap_name=sshd, action=start
ap_name=httpd, action=start
ap_name=redirect, action=start
bind: Address already in use
bind: Address already in use
ap_name=dnsmasq, action=start
ap_name=ftpd, action=start
ap_name=networkmap, action=start
ap_name=srt, action=restart
ap_name=rp, action=start
ap_name=udpecho, action=start
ap_name=ntp, action=start
ap_name=wlan, action=start
ap_name=ingress_qos, action=start
/bin/wlctl: Not Found
ap_name=ingress_classify, action=start
/bin/wlctl: Not Found
ap_name=qos_cls, action=start
Setting SSID: "caramelo2"
Setting SSID: "_ONOWiFi"
Setting SSID: "_AUTO_ONOWiFi"
Setting SSID: "Vodafone-H-500-s3"
/bin/wlctl: Not In Range
/bin/wlctl: Not In Range
killall: wifi_radar_2g: no process killed
killall: wifi_wd_2g: no process killed
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: selected channel spec: 0x100a
acsd: Adjusted channel spec: 0x100a
acsd: selected channel spec: 0x100a
7200 sec
flags: 0xb
index: 0 : Default
5 sec
2 sample period
1
28800 sec
killall: wps_det: no process killed
ap_name=qos_remark, action=start
ap_name=ipv6wd, action=start
ap_name=duplexmode, action=start
ap_name=cpm, action=start
ap_name=wanip, action=stop
ap_name=dnsmasq, action=stop
ap_name=dnsmasq, action=stop
ap_name=igd_upnp, action=start
ap_name=dnsr, action=start
ap_name=cron, action=start
ap_name=cups, action=start
ap_name=snmp, action=start
ap_name=3g, action=start
ap_name=emrd, action=start
ap_name=fon, action=start
ap_name=tr069, action=start
killall: cwmp: no process killed
ap_name=voip_qos, action=start
starting pid 1467, tty '': '/sbin/getty ttyS0 115200'
Vodafone-H-500-s login: complete
device eth3.300 is not a slave of br0
complete
complete
device eth3 is already a member of a bridge; can't enslave it to bridge br0.
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
Invalid QCSAPI option obss_coexist
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
complete
killall: wifi_radar_5g: no process killed
complete
could not open /proc/892/statcould not open /proc/893/stat
Vodafone-H-500-s login: admin
process '/sbin/getty ttyS0 15200' (pid 1467) exited. Scheduling for restart.
starting pid 1559, tty '': '/sbin/getty ttyS0 115200'
Vodafone-H-500-s login: admin
process '/sbin/getty ttyS0 15200' (pid 1559) exited. Scheduling for restart.
starting pid 1560, tty '': '/sbin/getty ttyS0 115200'
Vodafone-H-500-s login:
|
Pictures
- SerComm
- Embedded system/wireless router
- Embedded system/dsl modem
- Embedded system/CPE
- Embedded System Broadcom
- Embedded System BCM63167
- Broadcom
- Embedded System MIPS
- Embedded System BMIPS4350
- Embedded System Quantenna
- Embedded System QT3740BC
- Quantenna
- Embedded System ARC
- Embedded System 700
- Embedded System BCM53134S
- Manuf SerComm
- OpenWrt Supported
- Embedded System BCM63168
- Has Mimo Status
- Embedded System IEEE 802.11b/g/n
- Embedded System QT2518B
- Embedded System IEEE 802.11a/n/ac
- Dual-Radio Wireless Embedded System
- Wireless Embedded System
- Dual-Band
- Embedded System
- English Documentation
- Vodafone