TP-LINK CPE710 v1

multiple revisions of this device, use caution

an+ac (AC867)
5GHz AC 867Mbps 23dBi Outdoor CPE
Homepage	Product page
Wikipedia	TP-Link
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	TP-LINK CPE710 v1
FCC ID	TE7CPE710
Type	access point
CPU1 Y	Qualcomm Atheros QCA9563
CPU1 Type	MIPS 74Kc
CPU1 Speed	775 MHz
Flash1 Chip	Brand? Model?
Flash1 Size	16 MiB 16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> (SPI NOR)
RAM1 Size	128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (DDR2)
RAM1 Chip	Brand? Model?
ETH chip1	Qualcomm Atheros QCA9563
Ethernet Port Count	1-1GbE-LAN
Wired Standard	IEEE 802.3i/3u/3ab
802dot11 OUI: none specified
Stock bootloader	U-Boot
Expansion IF types	none specified
PoE	Passive
Power	16-27 VDC, ? A
Flags: Outdoor
Other
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Radio 1
Chip1	Qualcomm Atheros QCA9896
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11a/n/ac
802.11ac	up to 867 Mbps
802.11n	up to 300 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz
CPU1 brand Radio1 chip1 brand Radio1 chip2 brand TP-LINK CPE710 v1 Qualcomm Atheros Qualcomm Atheros TP-LINK CPE710 v2 Qualcomm Atheros Qualcomm Atheros

For a list of all currently documented Qualcomm Atheros (QCA) chipsets with specifications, see Qualcomm Atheros.

For a list of all currently documented TP-LINK devices with specifications, see TP-LINK.

• 867 Mbps - 2SS 5GHz 802.11ac (80MHz chan.) = AC867 class

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)
On the OpenWrt Wiki

Target: ath79
Subtarget: generic
Package architecture: mips_24kc
Supported Since Commit
Support started version: 22.03.0
Current supported version: 25.12.1

Unsupported Functions:
Pharos MAXtream
WLAN Hardware: Qualcomm Atheros QCA9896
WLAN Comment: 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector
Installation method(s):
GUI OEM
Recovery method(s):
TFTP generic

git • >>

ath79: add support for TP-Link CPE710-v1 TP-Link CPE710-v1 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on the AP152 reference board Specifications: - SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz - RAM: 128MiB DDR2 @ 650MHz - Flash: 16MiB SPI NOR Based on the GD25Q128 - Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless data rate) Based on the QCA9896 - Ethernet: one 1GbE port - 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector - Power, LAN, WLAN5G Blue LEDs - 3x Blue LEDs Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 30-40 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP address:192.168.0.254