TP-LINK EAP615-Wall v1

abgn+ac+ax (AX1800)
AX1800 Wall Plate WiFi 6 Access Point
Wikipedia	TP-Link
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	TP-LINK EAP615-Wall v1
FCC ID	2AXJ4EAP615WALL
Type	access point
CPU1 Y	MediaTek MT7621AT
CPU1 Type	MIPS 1004Kc
CPU1 Speed	880 MHz ( 2 cores ) 16-bit
Flash1 Chip	Brand? Model?
Flash1 Size	16 MiB 16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> (SPI NOR)
RAM1 Size	128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br />
RAM1 Chip	Brand? Model?
ETH chip1	MediaTek MT7621AT
Switch	MediaTek MT7621AT
Ethernet Port Count	4-1GbE-LAN
Wired Standard	IEEE 802.3i/3u/3ab
802dot11 OUI: none specified
Stock bootloader	U-Boot
Expansion IF types	none specified
PoE	802.3at, standard
Power	? VDC, ? A
Serial Port (UART)	yes, 3.3V TTL, (115200 8N1)
Other
3rd Party Firmware Support	OpenWrt • (List | Dev | DLs)
Radio 1
Chip1	MediaTek MT7905DAN
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11b/g/n/ax
802.11ax	up to 574 Mbps
802.11n	up to 300 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
Radio 2
Chip1	MediaTek MT7975DN
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11a/n/ac/ax
802.11ax	up to 1201 Mbps
802.11ac	up to 867 Mbps
802.11n	up to 300 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz

For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.

For a list of all currently documented TP-LINK devices with specifications, see TP-LINK.

• 574 Mbps - 2SS 2.4GHz 802.11ax (40MHz chan., 256-QAM),

• 1201 Mbps - 2SS 5GHz 802.11ax (80MHz chan., 1024-QAM) = AX1800 class

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)
On the OpenWrt Wiki
On the OpenWrt Forum

Target: ramips
Subtarget: mt7621
Package architecture: mipsel_24kc
Support started version: 22.03.0
Current supported version: 25.12.2

LAN Hardware: MediaTek MT7530
LAN Comment: PoE PSE out/passthrough on one port
WLAN Hardware: MediaTek MT7905DAN, MediaTek MT7975DN
WLAN Comment: 2x2 MU-MIMO, OFDMA
Installation method(s):
see git-commit
Install Comment:
rename image to shorter name, e.g. firmware.bin
Recovery method(s):
see git-commit

git • >>

ramips: support TP-Link EAP615-Wall Add support for the TP-Link EAP615-Wall, an AX1800 Wall Plate WiFi 6 AP. The device is very similar to the TP-Link EAP235-Wall. Hardware: * SoC: MediaTek MT7621AT * RAM: 128MiB * Flash: 16MiB SPI-NOR * Ethernet: 4x GbE * Back: ETH0 (PoE-PD) * Bottom: ETH1, ETH2, ETH3 (PoE passthrough) * WiFi: MT7905DAN/MT7975DN 2.4/5 GHz 2T2R * LEDS: 1x white * Buttons: 1x LED, 1x reset Stock firmware uses a random MAC address for ethernet. OpenWrt uses the MAC address that is on the device label for ethernet and the wireless interfaces. MAC address must not be incremented, as this will cause MAC address conflicts in case you have two devices with consecutive MAC addresses. Instead, different locally administered addresses will be generated automatically, based on the MAC on the label. Installation via stock firmware: * Enable SSH in the TP-Link web interface * SSH to the device * Run `cliclientd stopcs` * Upload the OpenWrt factory image via the TP-Link web interface Installation via bootloader: * Solder TTL header. Pinout: 1: TX, 2: RX, 3: GND, 4: VCC, with pin 1 closest to ETH1. Baud rate 115200 * Interrupt boot process by holding a key during boot * Boot the OpenWrt initramfs: # tftpboot 0x84000000 openwrt-ramips-mt7621-tplink_eap615-wall-v1-initramfs-kernel.bin # bootm * Copy openwrt-ramips-mt7621-tplink_eap615-wall-v1-squashfs-sysupgrade.bin to /tmp and use sysupgrade to install it Thanks to Sander Vanheule for his work on the EAP235-Wall, which made adding support for the EAP615-Wall very easy.