TP-LINK EAP680 v1
From TechInfoDepot
(Redirected from TP-Link EAP680 v1)
| abgn+ac+ax (AX6000) | |
|---|---|
| AX6000 Ceiling Mount WiFi 6 Access Point | |
|
| |
| Homepage | Product page |
| Wikipedia | TP-Link |
| 3rd Party Firmware | |
| dd-wrt | Status Unknown |
| OpenWrt | Supported |
| Tomato any flavor | Incompatible |
| Gargoyle | Status Unknown |
| Platform | |
| Brand • Model • Rev | TP-LINK EAP680 v1 |
| FCC ID | none specified |
| Type | access point |
| CPU1 | MediaTek MT7986AV |
| CPU1 Type | ARM Cortex-A53 |
| CPU1 Speed | 2.0 GHz ( 4 cores ) 64-bit |
| Flash1 Chip | Brand? Model? |
| Flash1 Size | 128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> |
| RAM1 Size | 1 GiB 1,024 MiB <br />1,073,741,824 B <br />8,388,608 Kib <br />1,048,576 KiB <br />8,192 Mib <br /> |
| RAM1 Chip | Brand? Model? |
| ETH chip1 | MediaTek MT7986AV |
| ETH chip2 | MaxLinear GPY211C |
| Ethernet Port Count | 1-2.5GbE-LAN |
| Wired Standard | IEEE 802.3i/3u/3ab/3bz |
|
802dot11 OUI: none specified | |
| Stock bootloader | U-Boot |
| Expansion IF types | none specified |
| Power | 12 VDC, 2 A |
| Serial Port (UART) | yes, 3.3V TTL, (115200 8N1) |
|
Flags: | |
|
| |
| Other | |
|
| |
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) |
| Radio 1 | |
| Chip1 | MediaTek MT7986AV |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 4x4:4 |
| Wireless Standard | IEEE 802.11b/g/n/ax |
| 802.11ax | up to 1148 Mbps |
| 802.11n | up to 600 Mbps |
| 802.11g | up to 54 Mbps |
| 802.11b | up to 11 Mbps |
| WiFi Operating Frequency | 2.4 GHz |
| Radio 2 | |
| Chip1 | MediaTek MT7986AV |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 4x4:4 |
| Wireless Standard | IEEE 802.11a/n/ac/ax |
| AX-QAM | up to 4804 Mbps |
| 802.11ax | up to 2402 Mbps |
| 802.11ac | up to 1733 Mbps |
| 802.11n | up to 600 Mbps |
| 802.11a | up to 54 Mbps |
| WiFi Operating Frequency | 5 GHz |
For a list of all currently documented MaxLinear (Intel) chipsets with specifications, see MaxLinear (Intel).
For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.
For a list of all currently documented TP-LINK devices with specifications, see TP-LINK.
Flashing
| NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
| The development branch can contain experimental code that is under active development and should not be used for production environments. Snapshot images may support additional hardware; however, it is experimental, considered unstable, and sometimes won't compile. |
| Prebuilt snapshot images do not come with any web interface or GUI. You will need to be comfortable using a command line and remote shell to install one yourself → How to install LuCI |
Target: mediatek
Subtarget: filogic
Package architecture: aarch64_cortex-a53
Support started version: unknown
Current supported version: snapshot
Subtarget: filogic
Package architecture: aarch64_cortex-a53
Support started version: unknown
Current supported version: snapshot
Unsupported Functions:
802.15.4 co-processor
LAN Comment: 1x 2.5GbE PoE uplink; MaxLinear GPY211C PHY (id 0x67c9de0a) at MDIO addr 5 on GMAC1, 2500base-x; enumerates as eth0
WLAN Hardware: MediaTek MT7986A
WLAN Comment: AX6000. 4x4 2.4GHz + 4x4 5GHz, HE/802.11ax, MCS 0-11. Calibration from the 'radio' file in the factory_data UBIFS. 802.11s mesh tested working.
Installation method(s):
Serial required: both OEM ingest paths are RSA-signed. TFTP initramfs to RAM from U-Boot, then sysupgrade. UART0 (ttyS0), 115200 8N1, 3.3 V; pads TP13=TX, TP14=RX, TP15=GND, TP16=VCC (RF side, next to J255)
Recovery method(s):
Serial, TP-Link rescue partition
Recovery Comment:
Hold reset at boot for TP-Link HTTP recovery; accepts signed OEM firmware only, restores stock.
Comment:
SPI-NAND on chip-select 1 with MediaTek NMBM. Stock A/B layout preserved: OpenWrt in slot A ('ubi'), stock kept in slot B ('ubi1') as a revert path. Carries a TI CC2652P7 BLE/802.15.4 co-processor on UART1, not driven by OpenWrt.
802.15.4 co-processor
LAN Comment: 1x 2.5GbE PoE uplink; MaxLinear GPY211C PHY (id 0x67c9de0a) at MDIO addr 5 on GMAC1, 2500base-x; enumerates as eth0
WLAN Hardware: MediaTek MT7986A
WLAN Comment: AX6000. 4x4 2.4GHz + 4x4 5GHz, HE/802.11ax, MCS 0-11. Calibration from the 'radio' file in the factory_data UBIFS. 802.11s mesh tested working.
Installation method(s):
Serial required: both OEM ingest paths are RSA-signed. TFTP initramfs to RAM from U-Boot, then sysupgrade. UART0 (ttyS0), 115200 8N1, 3.3 V; pads TP13=TX, TP14=RX, TP15=GND, TP16=VCC (RF side, next to J255)
Recovery method(s):
Serial, TP-Link rescue partition
Recovery Comment:
Hold reset at boot for TP-Link HTTP recovery; accepts signed OEM firmware only, restores stock.
Comment:
SPI-NAND on chip-select 1 with MediaTek NMBM. Stock A/B layout preserved: OpenWrt in slot A ('ubi'), stock kept in slot B ('ubi1') as a revert path. Carries a TI CC2652P7 BLE/802.15.4 co-processor on UART1, not driven by OpenWrt.
Please insert instructions here
Categories:
- TP-LINK
- Embedded system/access point
- Embedded System MediaTek
- Embedded System MT7986AV
- MediaTek
- Embedded System ARM
- Embedded System Cortex-A53
- Embedded System GPY211C
- Embedded System MaxLinear
- MaxLinear
- OpenWrt Supported
- Has Mimo Status
- Embedded System IEEE 802.11b/g/n/ax
- Embedded System IEEE 802.11a/n/ac/ax
- Dual-Radio Wireless Embedded System
- Wireless Embedded System
- Dual-Band
- Embedded System
- English Documentation
- New Entry