TechInfoDepot:JTAG/TIAO/USB Multi-Protocol Adapter
| TIAO USB Multi-Protocol Adapter | |
|---|---|
 TUMPA | |
| Homepage Support | TUMPA |
Quick Overview
USB to JTAG, SPI, I2C and Serial adapter, to debrick wireless routers, cable modems, use it as a standalone JTAG/SPI adapter, or program CPLD/FPGA, fully supported by OpenOCD, urjtag, xc3sprog
Product Description
This TIAO USB Multi-Protocol adapter is powered by FTDI's flagship communication chip FT2232H.
It supports the following protocols: JTAG, SPI, I2C and serial. With a 16-Bit Dual-Supply Bus Transceiver, this board can support voltage from 1.8v to 5.0v. It also uses a 3v to 5.5v multichannel RS232 Line driver/receiver for serial communication.
Supported softwares
- Openocd
- Urjtag
- FlashRom
- jtag pro
- zJTAG - Windows console JTAG application to debrick wireless routers
- XC3SPROG - Windows / Linux console application to program CPLD/FPGA
Package Content
- TIAO USB Multi-Protocol Adapter
- 80 PIN 2.54mm Header (2x40)
- 8 PCS 50cm female to female flexible cable
- 8 PCS 15cm female to female flexible cable
- 6 pogo pins
Technical Specificatons
- USB 2.0 Hi-Speed (480Mb/s)
- JTAG / IEEE 1149.1 compatible.
- JTAG Baudrate up to 30Mbits/sec (programmable)
- On board voltage translation via 74LVC14T245 (can be enabled / disabled via software or jumper)
- JTAG signals are 5V to 1.8V tolerant
- ARM Muli-ICE 20-pin header compatible.
- Separate SPI/I2C/Serial interfaces
- Configurable output of RS232 (MAX3243) or TTL level for serial communication
- Configurable auto power down for MAX3243
- Target board can be powered by TUMPA (3.3V) or self powered (via jumper)
- 4 on-board LEDs / PWR, Targt PWR, TX and RX
- 1 2x10 20 PIN JTAG header
- 1 2x5 10 PIN RS232 level 2.54mm IDC header
- 1 2x6 10 PIN TTL level 2.54mm IDC header
- 2 2x3 6 PIN SPI 2.54mm IDC header
- 1 x DB9 connector (male, RS232 level)
- Target board power jumper
- Buffer chip enable jumper
- RS232 chip auto power down jumper
- RS232 or TTL output jumber
- USB Hot-Plug / JTAG Hot-Plug.
- USB over-current protection via on-board resetable fuse.
- Strong ESD protection on USB signals.
- Based on the FTDI FT2232H USB device.
- Designed for FTDI MPSSE easy-to-use.
- Free drivers for Linux.
- Free drivers for Windows XP, Windows Vista and Windows 7
- Support both 32 bit and 64 bit operating systems
- Board dimension: 65.41mm X 58.55mm (2.58" X 2.31")
You can use this USB based multi-protocol adapter to JTAG your router, cable modem or any JTAG/SPI devices. For drivers, product manuals, please check it out here http://www.tiaowiki.com/w/JTAG_Tutorials
Additional Information
Manufacturer TIAO Corp. Warranty 1 year limited replacement warranty JTAG Type Cable Modem, Free to Air Receiver, Non Free to Air Receiver, Wiggler, Wireless Router Is Buffered? Yes Use Printed Circuit Boad? Yes Pins 20 (Standard Wiggler)
Buy various JTAG cables for your Satellite Receiver, Cable Modem, Wireless Router, Standard Wiggler from http://www.easymg.com and http://www.diygadget.com
Tutorials
- Install TIAO USB Multi Protocol Adapter Driver on Windows XP
- Install TIAO USB Multi Protocol Adapter Driver on Windows Vista or Windows 7
- USB Multi Protocol Adapter User's Manual
- How to Debrick Wireless Router Using TUMPA and zJTAG
- How to debrick a router with TUMPA and TJTAG-PRO (Coming Soon)
- How set up TUMPA for Serial output (Coming Soon)
Pictures
- TIAO Images
