Teltonika RUT230
From TechInfoDepot
Jump to navigationJump to search
| bgn (N150) | |
|---|---|
| industrial 3G router | |
 | |
| Homepage | Product page |
| 3rd Party Firmware | |
| dd-wrt | Status Unknown |
| OpenWrt | Supported |
| Tomato any flavor | Incompatible |
| Gargoyle | Status Unknown |
| Platform | |
| Brand • Model • Rev | Teltonika RUT230 |
| FCC ID | none specified |
| Type | wireless router |
CPU1  | Atheros AR9331 |
| CPU1 Type | MIPS 24Kc |
| CPU1 Speed | 400 MHz |
| Flash1 Chip | Brand? Model? |
| Flash1 Size | 16 MiB 16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> (SPI NOR) |
| RAM1 Size | 64 MiB 67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br /> (DDR2) |
| RAM1 Chip | Brand? Model? |
| ETH chip1 | Atheros AR9331 |
| Ethernet Port Count | 1-100MbE-LAN |
| Wired Standard | IEEE 802.3i/3u |
|
802dot11 OUI: none specified | |
| Stock bootloader | U-Boot |
| Expansion IF types | none specified |
| PoE | Passive |
| Power | 9-30 VDC, ? A |
| JTAG Port | no |
|
Flags: | |
|
| |
| Other | |
|
| |
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) |
| Retail | |
| Availability | End of Life |
| End of Life date | 2021 |
| Radio 1 | |
| Chip1 | Atheros AR9331 |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 1x1:1 |
| Wireless Standard | IEEE 802.11b/g/n |
| 802.11n | up to 150 Mbps |
| 802.11g | up to 54 Mbps |
| 802.11b | up to 11 Mbps |
| WiFi Operating Frequency | 2.4 GHz |
For a list of all currently documented Atheros (QCA) chipsets with specifications, see Atheros.
- • 150 Mbps - 1SS 2.4GHz 802.11n (40MHz chan.) = N150 class
Flashing
 | NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
 | This device is NOT RECOMMENDED for future use with OpenWrt due to low flash/ram.
DO NOT BUY DEVICES WITH 8MB FLASH / 64MB RAM if you intend to flash an up-to-date and secure OpenWrt version onto it! See 8/64 warning for details. This device does not have sufficient resources (flash and/or RAM) to provide secure and reliable operation. This means that you will not be able to install many packages, and that you might experience crashes due to OOM situations more or less often. See OpenWrt on 8/64 devices what you can do now. |
Target: ath79
Subtarget: generic
Package architecture: mips_24kc
Supported Since Commit
Support started version: 22.03.0
Current supported version: 25.12.1
Subtarget: generic
Package architecture: mips_24kc
Supported Since Commit
Support started version: 22.03.0
Current supported version: 25.12.1
WLAN Comment: Atheros AR9331
Installation method(s):
GUI OEM, U-Boot web recovery, see git-commit
Recovery method(s):
U-Boot web recovery, see git-commit
Installation method(s):
GUI OEM, U-Boot web recovery, see git-commit
Recovery method(s):
U-Boot web recovery, see git-commit
| git • >> |
|---|
ath79: add support for Teltonika RUT230 v1 This commit adds support for the Teltonika RUT230 v1, a Atheros AR9331 based router with a Quectel UC20 UMTS modem. Hardware -------- Atheros AR9331 16 MB SPI-NOR XTX XT25F128B 64M DDR2 memory Atheros AR9331 1T1R 802.11bgn Wireless Boootloader: pepe2k U-Boot mod Hardware-Revision ----------------- There are two board revisions of the RUT230, a v0 and v1. A HW version is silkscreened on the top of the PCBs front side as well as shown in the Teltonika UI. However, this looks to be a different identifier, as the GPl dump shows this silkscreened / UI shown version are internally treated identically. Th following mapping has been obtained from the latest GPl dump. HW Ver 01 - 04 --> v0 HW Ver > 05 --> v1 My board was a HW Ver 09 and is treated as a v1. Installation ------------ While attaching power, hold down the reset button and release it after the signal LEDs flashed 3 times. Attach your Computer with the devices LAN port and assign yourself the IPv4 address 192.168.1.10/24. Open a web browser, navigate to 192.168.1.1. Upload the OpenWrt factory image. The device will install OpenWrt and automatically reboots afterwards. You can use the smae procedure with the stock firmware to return back to the vendor firmware. |
