Teltonika RUT906
From TechInfoDepot
Jump to navigationJump to search
| bgn (N300) | |
|---|---|
| 4G LTE RS232/RS485 Router | |
 | |
| Homepage | Product page |
| 3rd Party Firmware | |
| dd-wrt | Status Unknown |
| OpenWrt | Supported |
| Tomato any flavor | Incompatible |
| Gargoyle | Status Unknown |
| Platform | |
| Brand • Model • Rev | Teltonika RUT906 |
| FCC ID | none specified |
| Type | wireless router |
CPU1  | MediaTek MT7628AN |
| CPU1 Type | MIPS 24KEc |
| CPU1 Speed | 580 MHz |
| Flash1 Chip | Brand? Model? |
| Flash1 Size | 16 MiB16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> (microSDXC) |
| RAM1 Size | 128 MiB 134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> |
| RAM1 Chip | Brand? Model? |
| ETH chip1 | MediaTek MT7628AN |
| Switch | MediaTek MT7628AN |
| Ethernet Port Count | 4-100MbE-LAN |
| Wired Standard | IEEE 802.3i/3u |
|
802dot11 OUI: none specified | |
| Stock bootloader | U-Boot |
| Expansion IF types | microSDXC, USB 2.0 |
| USB ports | 1 |
| SD/MMC Slots | 1 |
| USB Hub Compatible | Untested |
| Power | 9-30 VDC, ? A |
| Serial Port (UART) | yes |
|
Flags: | |
|
| |
| Other | |
|
| |
| 3rd Party Firmware Support |
OpenWrt • (List | Dev | DLs) |
| Radio 1 | |
| Chip1 | MediaTek MT7628AN |
| Wireless interface OUI | none specified |
| Antenna Connector Type | none specified |
| MIMO status | 2x2:2 |
| Wireless Standard | IEEE 802.11b/g/n |
| 802.11n | up to 300 Mbps |
| 802.11g | up to 54 Mbps |
| 802.11b | up to 11 Mbps |
| WiFi Operating Frequency | 2.4 GHz |
For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.
- • 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.) = N300 class
Flashing
 | NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
Target: ramips
Subtarget: mt76x8
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 25.12.0
Current supported version: 25.12.2
Subtarget: mt76x8
Package architecture: mipsel_24kc
Supported Since Commit
Support started version: 25.12.0
Current supported version: 25.12.2
LAN Hardware: MediaTek MT7628AN
LAN Comment: Meig SLM770A modem, passive PoE on LAN1
WLAN Hardware: MediaTek MT7628AN
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
Comment:
IP30 Ingress Protection, Industrial rated
LAN Comment: Meig SLM770A modem, passive PoE on LAN1
WLAN Hardware: MediaTek MT7628AN
Installation method(s):
see git-commit
Recovery method(s):
see git-commit
Comment:
IP30 Ingress Protection, Industrial rated
| git • >> |
|---|
ramips: mt76x8: add Teltonika RUT956/RUT906 support Specification: - MediaTek MT7628AN SoC - 128 MB of RAM EtronTech EM68C16CWQG-25IH - 16MB of Flash Winbond W25Q128 SPI - 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1 - MediaTek MT7628AN 2.4 GHz 802.11n WiFi - Quectel EC25-EUX (RUT956) or Meig SLM770A (RUT906) modem - GNSS - RS232, DB9 connector, Cypress ACM via USB, /dev/ttyACM0 - RS485 /dev/ttyS1 - microSD card slot - 2.0 USB Type-A HOST port - analog 0-24V input (MCP3221) - Relay - 2x Digital input - 2x Digital output - 2x SIM slot (can be swapped via GPIO) - eSIM (depends on hardware configuration, can be swapped via GPIO) GPIO: - 1 button (Reset) - 7 LEDs (power, status green/red, RSSI 1,2,3,4,5) - 5 Modem control (power button, reset, status (v5 hw), SIM select, eSIM select) - 2 Digital input - 2 Digital output - 1 Isolated input - 1 RS485 tx enable - 1 RS485 rx enable - 1 Relay - 1 Data Carrier Detect (DCD) Flashing via OEM WebUI: 1. Download the firmware image *-squashfs-factory.bin 2. Upload firmware image via OEM WebUI firmware update, do not keep settings To revert back to OEM firmware: https://wiki.teltonika-networks.com/view/Bootloader_menu Mobile data connection: Meig SLM770 create proto DHCP interface with usb0 device. Quectel EC25-EUX create proto qmi interface. |
